LS Industrial Systems STARVERT iG5A User manual

Automation Equipment
Leader in Electrics & Automation
STARVERT iG5A
Compact & Powerful Inverter
0.4~7.5kW 3Phase 200~230Volts
0.4~7.5kW 3Phase 380~480Volts

2
LS Starvert iG5A is very competitive in its price and shows an upgraded functional
strength compared to iG5. User-friendly interface, extended inverter ranges up to .5kW,
superb torque competence and small size of iG5A provides an optimum use environment.
STARVERT iG5A
Inverter
iG5A
User-
friendliness
& Easy
maintenance
Standard
compliance
High
performance
Compactness

Compact & Powerful Inverter iG5A
3
Overview
Model & Type
Standard Specifications
Wiring
Terminal Configurations
Keypad Features
Parameter Setting
Trial Run
Dimensions
Braking Resistors and Peripheral Devices
Function List
Protective Functions
Fault Remedy
4
8
9
11
12
13
14
16
18
20
21
28
29
Contents

iG5A
4
Powerful & Upgraded Performance
iG5A provides sensorless vector control, PID control,
and ground-fault protection through powerful built-in functions.
The built-in PID function enables to control
flow-rate, oil-pressure, temperature, etc
without any extra controller.
The built-in sensorless vector control provides
the superb speed control and powerful high
torque.
Inputting analog signals from -10V to 10V
provides user-friendly operation.
Built-in PID control
Analog control from -10V to 10V
Sensorless vector control
Condition :
SSppeeeedd vvss TToorrqquuee CChhaarraacctteerriissttiiccss
Speed (Hz)
Torque (%)
Sensorless Vector Control Mode: Auto tuning Measure maximum
torque (%) at each speed (1/5/1 /2 /3 /4 /5 /6 Hz)
+10
-10
Forward
Reverse
◀
◀
The built-in dynamic braking circuit minimizes
deceleration time via braking resistors.
Built-in dynamic braking circuit Speed
Time
With braking resistor
Reducing
deceleration time
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PI control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
PID control
The built-in RS-485 communication supports
remote control and monitoring between iG5A
and other equipment.
Built-in 485 communication
The ground-fault protection of output terminal
is possible during running.
Ground-fault protection
during running
iG5A consists of the product range from 0.4 to 7.5kW.
Wide product range
◀
Normal state
◀

Compact & Powerful Inverter iG5A
5
Checking operation status
(Voltage, Current, Frequency, etc)
Checking modified parameters
Windows support
Monitoring
Connected to PC
Connected to XGT panel
Checking operation time
Display of Korean error message
Automatic list-up of trip record
Language support (Korean, English, Chinese)
Monitoring
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Inverters
RS-485, Modbus communication
Remote Control
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Inverters
RS-485, Modbus communication
Remote Control
RS-485 - 232C converter
RS-485 communication

6
User-friendly Interface & Easy Maintenance
The parameter setting becomes easier b adopting the 4 directions ke . And iG5A supports
eas maintenance via diagnosis and fan changeable structure.
By controlling the cooling fan, iG5A provides a virtually
quiet environment according to the status of operation.
iG5A
Cooling fan control
The 4 directions key provides easy handling and
monitoring.
User-friendly interface
iG5A is designed to be the fan changeable structure in
preparation for a fan breakdown.
Easy change of fan
The external loader away from a panel enables to control
and monitor conveniently. And the parameters made by
external loader can be copied and applicable to other
Inverters.
Loader type + External type (Optional)
Non-loader type + External type (Optional)
External loader (Optional)
Remarks
2m
3m
5m
Model name
INV, REMOTE KPD 2M (SV-iG5A)
INV, REMOTE KPD 3M (SV-iG5A)
INV, REMOTE KPD 5M (SV-iG5A)
Through easy parameter setting, iG5A can diagnose the
status of output module.
Diagnosis of output module
�N (ex: SV00ZiG5A-2N) means non-loader Inverter.

Compact & Powerful Inverter iG5A
7
Compact Size
The compact size, improved b 46% smaller than
iG5 achieves cost-efficienc and various applications.
Both PNP and NPN inputs become possible and these enable to
use the outer power.
To do so, users will be given wider choices of selecting the
controller.
PNP/NPN input
iG5A series complies with CE and UL (Type1) standards.
Global standard
Global standard compliance
CE U
Same height from 0.4 to 4.0kW (128mm)

iG5A
8
Model & Type
200V Series
SV004iG5A-2
SV008iG5A-2
SV015iG5A-2
SV022iG5A-2
SV037iG5A-2
SV040iG5A-2
SV055iG5A-2
SV075iG5A-2
Applicable motor ranges
0.4kW (0.5HP)
0.75kW (1HP)
1.5kW (2HP)
2.2kW (3HP)
3.7kW (5HP)
4.0kW (5.4HP)
5.5kW (7.5HP)
7.5kW (10HP)
400V Series
SV004iG5A-4
SV008iG5A-4
SV015iG5A-4
SV022iG5A-4
SV037iG5A-4
SV040iG5A-4
SV055iG5A-4
SV075iG5A-4
STARVERT
Motor rating (kW)
(004: 0.4kW~075: 7.5kW)
iG5A series
Input voltage
(2: 220V Series, 4: 400V Series)
Non-loader (Optional)
015 iG5A 2
SV N

Compact & Powerful Inverter iG5A
9
Standard Specifications
200V Series
SV������iG5A-2 ��
5)
4)
Max.
capacity 1) (HP)
(kW)
Output
rating
Capacity (kVA)
Rated current (A)
Max. output frequency (Hz)
Max. output voltage (V)
Voltage (V)
Frequency (Hz)
Cooling method
Weight
Input
rating
1) Indicate the maximum applicable motor capacity when using 4 pole LS standard motor.
2) Rated capacity is based on 220V for 200V series and 440V for 400V series.
3) Refer to 15-3 of user’s manual when carrier frequency setting (39) is above 3kHz.
4) Max. frequency setting range is extended to 300Hz when H40 (Control mode select) is set to 3 (Sensorless vector control).
5) Max. output voltage cannot be higher than the input voltage. It can be programmable below input voltage.
2)
3)
SV������iG5A-4 ��
5)
4)
Max.
capacity 1) (HP)
(kW)
Output
rating
Capacity (kVA)
Rated current (A)
Max. output frequency (Hz)
Max. output voltage (V)
Voltage (V)
Frequency (Hz)
Cooling method
Weight
Input
rating
2)
3)
400V Series
075055040037022015008004
10
7.5
12.2
32
3.66
075
10
7.5
12.2
16
3.66
055
7.5
5.5
9.1
12
3.66
040
5.4
4.0
6.9
9
1.89
037
5
3.7
6.1
8
1.89
022
3
2.2
4.5
6
1.84
015
2
1.5
3.0
4
1.12
008
1
0.75
1.9
2.5
0.77
004
0.5
0.4
0.95
1.25
0.76
7.5
5.5
9.1
24
3.66
5.4
4.0
6.5
17
1.89
5
3.7
6.1
16
1.89
3
2.2
4.5
12
1.84
2
1.5
3.0
8
1.12
1
0.75
1.9
5
0.77
0.5
0.4
0.95
2.5
0.76
400
3 phase 200~230
3 phase 200~230VAC (+10%, -15%)
50~60 (±5%)
400
3 phase 380~480
3 phase 380~480VAC (+10%, -15%)
50~60 (±5%)
Forced air cooling
Forced air cooling
Natural
Natural

iG5A
10
Standard Specifications
1) Means average braking torque during Decel to stop of a motor.
2) Refer to Chapter 16 of user’s manual for DB resistor specification.
Over voltage, Under voltage, Over current, Ground fault current detection, Inverter overheat,
Motor overheat, Output phase open, Overload protection, Communication error,
Loss of speed command, Hardware fault, Fan trip
V/F, Sensorless vector control
Linear, Squared, User V/F
150% per 1 min.
Manual/Auto torque boost
20%
150% when using optional DB resistor
Digital command: 0.01Hz
Analog command: 0.06Hz (Max. freq.: 60Hz)
Digital command: 0.01% of Max. output frequency
Analog command: 0.1% of Max. output frequency
Trip
Alarm
Momentary power loss
Operation mode
Frequency setting
Operation features
Dynamic
braking
Input
Output
Max. braking
torque
Max. Duty
Open collector
terminal
Multi-function relay
Analog output (AM)
IP 20, NEMA Type 1 (Optional)
-10℃~50℃
-20℃~65℃
Below 90% RH (No condensation)
Below 1,000m, 5.9m/sec
2
(0.6G)
70~106 kPa
Protected from corrosive gas, Combustible gas, Oil mist or dust
1)
2)
Keypad/ Terminal/ Communication option/ Remote keypad selectable
PID, Up-down, 3-wire
NPN/PNP selectable
0~10Vdc (less than 10mA): Output freq, Output current, Output voltage, DC link selectable
FWD/REV RUN, Emergency stop, Fault reset, Jog operation, Multi-step Frequency-High, Mid, Low,
Multi-step Accel/Decel-High, Mid, Low, DC braking at stop, 2nd motor select, Frequency UP/Down,
3-wire operation, External trip A, B, PID-Inverter (V/F) operation bypass,
Option-inverter (V/F) operation bypass, Analog Hold, Accel/Decel stop
Analog: 0~10V, -10~10V, 0~20mA
Digital: Keypad
Fault output and
inverter status output Less than DC 24V, 50mA
(N.O., N.C.) Less than AC 250V, 1A; Less than DC 30V, 1A
Stall prevention, Overload
Below 15 msec.: Continuous operation (Should be within rated input voltage, rated output power.)
Above 15 msec.: Auto restart enable
Protection degree
Ambient temp
Storage temp
Humidity
Altitude/Vibration
Atmospheric pressure
Location
Control method
Frequency setting resolution
Frequency accuracy
V/F pattern
Overload capacity
Torque boost
Multi-function
terminal
P1~P8
Environ
ment
Control
Protective
function
Operation

Compact & Powerful Inverter iG5A
11
Wiring
P1
P2
CM
P3
P4
P5
CM
P6
P7
P8
24
R
S
T
G
U
V
W
AM
CM
3A
3C
3B
MO
MG
S+
S-
DB resistor
(Optional)
3 phase AC input
(Rated input voltage)
VR
V1
I
CM
B1 B2
A contact output
A/B contact common
B contact output
FX (Forward run)
RX (Reverse run)
Input signal common
BX (Emergency stop)
RST (Trip reset)
JOG (Jog operation)
Input signal common
Multi-step freq. - Low
Multi-step freq. - Middle
Multi-step freq. - High
24V output
Ground
10V power supply for potentiometer
Freq. Setting Voltage signal input: -10~10V
Freq. Current signal input: 0~20mA
Input signal common
Multi-function open
collector output
MO Common
Potentiometer
(1kohm, 1/2W)
RS-485 communication terminal
Multi-function
analog output
signal: 0~10V

MO
3A 3B 3C P5 CM P6 P7 P8 VR V1 I AM
MG 24 P1 P2 CM P3 P4 S-S+
Multi-function input T/M 1-8
Common terminal
Power supply for external
potentiometer
Input terminal for voltage operation
Input terminal for current operation
Multi-function analog output terminal
Multi-function terminal for open collector
Ground terminal for external power supply
24V external power supply
Multi-function relay output A contact
Multi-function relay output B contact
Common for multi-function relays
Description Screw size
Single wire Stranded Torque (Nm) Specification
P1~P8
CM
VR
V1
I
AM
MO
MG
24
3A
3B
3C
1) Use Copper wires rated 600V, 75℃and higher.
2) Use the recommended tightening torque when securing terminal screws.
※When you use external power supply (24V) for multi-function input terminal (P1~P8), apply voltage higher than 12V to activate.
※Tie the control wires more than 15cm away from the control terminals. Otherwise, it interferes front cover reinstallation.
Terminal
Inverter capacity 200V Series
Wire size Terminal screw
Grounding method Wire size Terminal screw Grounding method
400V Series
• 0.4~1.5kW (200V/400V) • 5.5~7.5kW (200V/400V)
Terminal Description
R, S, T
B1, B2
U, V, W
AC Line voltage input
Connection terminal for DB resistor (Optional)
Connection terminal for motor
Wire size (mm
22
)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
Output voltage: 12V
Max. output current: 100mA
Potentiometer: 1~5kohm
Max. input voltage:
-12V~+12V input
0~20mA input
Internal resistor: 500ohm
Max. output voltage: 11V
Max. output current: 100mA
Below DC 26V,100mA
Max. output current: 100mA
Below AC 250V, 1A
Below DC 30V, 1A
R S T B1 B2 R S T B1 U V W
U V W
B1
R S T
U V W
B2 B2
Specifications for power terminal block wiring
Control terminal specifications
• 2.2~4.0kW (200V/400V)
1) 1)
2)
0.4~0.75kW
1.5kW
2.2kW
3.7~4.0kW
5.5kW
7.5kW
2mm
2
2mm
2
2mm
2
3.5mm
2
5.5mm
2
8mm
2
M3.5
M3.5
M4
M4
M5
M5
2mm
2
2mm
2
2mm
2
2mm
2
3.5mm
2
3.5mm
2
M3.5
M4
M4
M4
M5
M5
Type 3 Special
Type 3
iG5A
12
Terminal Configuration

Display Term
Run key
STOP/RESET key
Up key
Down key
Right key
Left key
Enter key
Forward run
Reverse run
Run key
Setting
RUN
STOP/RESET
▲▲
▼▼
▶▶
◀◀
●●
FWD
REV
RUN
SET
KEY
LED
Description
Run command
STOP: Stop command during operation,
RESET: Reset command when a fault occurs.
Used to scroll through codes or increase parameter value
Used to scroll through codes or decrease parameter value
Used to jump to other parameter groups or move a cursor to
the right to change the parameter value
Used to jump to other parameter groups or move a cursor to
the left to change the parameter value
Used to set the parameter value or save the changed parameter value
Lit during forward run
Lit during reverse run
Lit during operation
Lit during parameter setting
Dimensions
95
ENT
SET FWD
REV
STOP
RESET
RUN
RUN
36.2
72.4 65.6 3.4
2-∅4.5
83
5 13.9
2.1 23.1
70
C
L
1)
1) 4 LEDs above are set to blink when a fault occurs.
Compact & Powerful Inverter iG5A
13
Keypad Features

iG5A
14
Moving to Other Groups
Moving to other groups
Parameter groups
Parameter group
Moving to other groups using the Right (▶▶) key Moving to other groups using the Left (◀◀) key
Description
Drive group
Function group 1
Function group 2
I/O (Input/Output) group
Basic parameters necessary for the inverter to run. Parameters such as Target frequency, Accel/Decel time settable.
Basic function parameters to adjust output frequency and voltage.
Advanced function parameters to set parameters for such as PID Operation and second motor operation.
Parameters necessary to make up a sequence using multi-function input/output terminal.
1) Target frequency can be set at 0.0 (the 1st code of drive group). Even though the preset value is 0.0, it is user-settable.
The changed frequency will be displayed after it is changed.
1) 1)
There are 4 different parameter groups in iG5A series as shown below.

Compact & Powerful Inverter iG5A
15
When changing ACC time from 5.0 sec to 16.0 sec
∙In the first code“0.00”, press the Up (▲) key once to go to the second code.
∙ACC [Accel time] is displayed.
∙Press the Ent (●) key once.
∙Preset value is 5.0, and the cursor is in the digit 0.
∙Press the Left (◀) key once to move the cursor to the left.
∙The digit 5 in 5.0 is active. Then press the Up (▲) key once.
∙The value is increased to 6.0
∙Press the Left (◀) key to move the cursor to the left.
∙0.60 is displayed. The first 0 in 0.60 is active.
∙Press the Up (▲) key once.
∙16.0 is set.
∙Press the Ent (●) key once.
∙16.0 is blinking.
∙Press the Ent (●) key once again to return to the parameter name.
∙ACC is displayed. Accel time is changed from 5.0 to 16.0 sec.
1
2
3
4
5
6
7
8
Code change in Drive group
∙In the 1st code in Drive group“0.00”,
press the Up (▲) key once.
∙The 2nd code in Drive group“ACC”is displayed.
∙Press the Up (▲) key once.
∙The 3rd code“dEC”in Drive group is displayed.
∙Keep pressing the Up (▲) key until the last code appears.
∙The last code in Drive group "drC”is displayed.
∙Press the Up (▲) key again.
∙Return to the first code of Drive group.
∙Use Down (▼) key for the opposite order.
1
2
3
4
5
1)
1) Pressing the Left (◀)/Right (▶)/Up (▲)/Down (▼) key while a cursor is blinking will cancel the parameter value change.
Pressing the Ent (●) key in this status will enter the value into memory.
※In step 7, pressing the Left (◀) or Right (▶) key while 16.0 is blinking will disable the setting.

iG5A
16
Trial Run
Operation condition
1. Please make sure that R, S, T are connected to 3 phase AC input, and
U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step among
Low, Middle, and High.
3. If P1 (FX) turns on, the motor operates in forward. And after turning off,
it stops according to the deceleration time.
4. If P2 (RX) turns on, the motor operates in reverse. And after turning off,
it stops according to the deceleration time.
Operation command:
Run/Stop via FX/RX Max. frequency change: From 60Hz to 80Hz
Frequency command:
Multi-step operation [Low (20), Middle (30), High (80)]
P1 (Forward)
P2 (Reverse)
P6 (Low)
P7 (Middle)
P8 (High)
CM
Step Command After changeDefaultCode Description
1
2
3
4
5
6
F21
st1
st2
I30
I17
I18
Max. frequency change (FU1)
Multi-step frequency (DRV)
Multi-step frequency (DRV)
Multi-step frequency (I/O)
Forward run (P1: FX)
Reverse run (P2: RX)
Change Max. frequency.
Set‘Low’step.
Set‘Middle’step.
Set‘High’step.
The default is FX. This value may change.
The default is RX. This value may change.
60Hz
10Hz
20Hz
30Hz
FX
RX
80Hz
20Hz
30Hz
80Hz
FX
RX
S1
S2
S3
S4
S5
Multi-step operation + Run/Stop via FX/RX + Max. frequency change
Wiring
Parameter setting
P1 (Forward)
P2 (Reverse)
P6 (Low)
P7 (Middle)
P8 (High)
CM
RR
SS
TT
GG
VR
V1
CM
UU
VV
WW
S / W
3 phase
AC input

Compact & Powerful Inverter iG5A
17
1. Please make sure that R, S, T are connected to 3 phase AC input,
and U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step
among Low, Middle, and High.
3. If P1 (FX) turns on, the motor operates in forward. And after
turning off, it stops according to the deceleration time.
4.If P2 (RX) turns on, the motor operates in reverse. And after
turning off, it stops according to the deceleration time.
5. Control the motor’s speed via potentiometer.
Operation command:
Run/Stop via FX/RX Frequency command: 0~60Hz analog input via potentiometer Accel/Decel time: Accel-10sec, Decel-20sec
Operation condition
P1 (FX) Forward
P2 (RX) Reverse
CM
VR
V1
CM
Potentiometer
1~5kohm, 1/2W
R
S
T
G
U
V
W
3 phase
AC input
Motor
Step Command After changeDefaultCode Description
1
2
3
4
5
Drv
Frq
I17
I18
Analog input
(DRV group)
Accel/Decel time
(DRV group)
Forward run
(P1: FX)
Reverse run
(P2: RX)
Operation command
(DRV group) Turn on/off motor via terminal.
Change keypad command to analog voltage command.
Set Accel time to 10sec in ACC
Set Decel time to 20sec in dEC.
The default is FX. This value may change
The default is RX. This value may change.
1 (FX/RX-1)
0 (Keypad-1)
5sec (Accel)
10sec (Decel)
FX
RX
1 (FX/RX-1)
3 (V1: 0~10V)
10sec (Accel)
20sec (Decel)
FX
RX
0~60Hz
Potentiometer 1~5kohm, 1/2W
VR
V1
CM
1
2
3
Wiring
Potentiometer (Volume) + Run/Stop via FX/RX + Accel/Decel time change
Parameter setting
ACC
dEC

iG5A
18
Dimensions
SV004IG5A-2
SV008IG5A-2
SV004IG5A-4
SV008IG5A-4
0.4
0.75
0.4
0.75
70
70
70
70
65.5
65.5
65.5
65.5
128
128
128
128
119
119
119
119
130
130
130
130
4.0
4.0
4.0
4.0
4.5
4.5
4.5
4.5
4.0
4.0
4.0
4.0
0.76
0.77
0.76
0.77
mm (inches)
SV004iG5A-2 / SV008iG5A-2, SV004iG5A-4 / SV008iG5A-4
SV015iG5A-2 / SV015iG5A-4
SV015IG5A-2
SV015IG5A-4 1.5 1.5 100 100 95.5 95.5 128 128 120 120 130 130 4.5 4.5 4.5 4.5 4.5 4.5 1.12 1.12
mm (inches)
W
W
W1
W1
A
A1
H1
H
D
B
D
H
W1
W1
B
∅
A
A
H1
∅
Inverter model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ∅A (mm) B (mm) (kg)
Inverter model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ∅A (mm) B (mm) (kg)

Compact & Powerful Inverter iG5A
19
SV022iG5A-2 / SV037iG5A-2 / SV040iG5A-2, SV022iG5A-4 / SV037iG5A-4 / SV040iG5A-4
SV055iG5A-2 / SV075iG5A-2, SV055iG5A-4 / SV075iG5A-4
SV004IG5A-2
SV008IG5A-2
SV004IG5A-4
SV008IG5A-4
5.5
7.5
5.5
7.5
180
180
180
180
170
170
170
170
220
220
220
220
210
210
210
210
170
170
170
170
4.5
4.5
4.5
4.5
5
5
5
5
4.5
4.5
4.5
4.5
3.66
3.66
3.66
3.66
mm (inches)
Inverter model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ∅A (mm) B (mm) (kg)
SV022IG5A-2
SV037IG5A-2
SV040IG5A-2
SV022IG5A-4
SV037IG5A-4
SV040IG5A-4
2.2
3.7
4.0
2.2
3.7
4.0
140
140
140
140
140
140
132
132
132
132
132
132
128
128
128
128
128
128
120.5
120.5
120.5
120.5
120.5
120.5
155
155
155
155
155
155
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
1.84
1.89
1.89
1.84
1.89
1.89
mm (inches)
W
W1
C
L
H1 A
BB
H
D
∅
∅
WW
W
H1
A
A
BB
D
H
Inverter model (kW) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) ∅A (mm) B (mm) (kg)

iG5A
20
Braking Resistors and Peripheral Devices
200V Series
400V Series
Voltage Inverter 100% braking 150% braking
Resistor [Ω] Watt [W]Resistor [Ω] Watt [W]
0.4
0.75
1.5
2.2
3.7
5.5
7.5
0.4
0.75
1.5
2.2
3.7
5.5
7.5
400
200
100
60
40
30
20
1800
900
450
300
200
120
90
50
100
200
300
500
700
1000
50
100
200
300
500
700
1000
300
150
60
50
33
20
15
1200
600
300
200
130
85
60
100
150
300
400
600
800
1200
100
150
300
400
600
1000
1200
Model AC external fuse AC reactor
Current [A] Voltage [V]
10
10
15
25
30
30
30
50
5
10
10
10
20
20
20
30
004iG5A-2
008iG5A-2
015iG5A-2
022iG5A-2
037iG5A-2
040iG5A-2
055iG5A-2
075iG5A-2
004iG5A-4
008iG5A-4
015iG5A-4
022iG5A-4
037iG5A-4
040iG5A-4
055iG5A-4
075iG5A-4
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
4.20mH, 3.5A
2.13mH, 5.7A
1.20mH, 10A
0.88mH, 14A
0.56mH, 20A
0.56mH, 20A
0.39mH, 30A
0.28mH, 40A
18.0mH, 1.3A
8.63mH, 2.8A
4.81mH, 4.8A
3.23mH, 7.5A
2.34mH, 10A
2.34mH, 10A
1.22mH, 15A
1.14mH, 20A
Model Breaker
Voltage [V]
Current [A]
30
30
30
30
30
30
50
60
220
220
220
220
220
220
220
220
004iG5A-2
008iG5A-2
015iG5A-2
022iG5A-2
037iG5A-2
040iG5A-2
055iG5A-2
075iG5A-2
Model Breaker Voltage [V]Current [A]
30
30
30
30
30
30
30
30
460
460
460
460
460
460
460
460
004iG5A-4
008iG5A-4
015iG5A-4
022iG5A-4
037iG5A-4
040iG5A-4
055iG5A-4
075iG5A-4
Braking resistors
Breakers
Fuses & AC reactors
1) The wattage is based on Enable Duty (%ED) with continuous braking time 15sec.
1) 1)