LST AOEX-55000-640 User manual

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
Ex-ApoDisc_DBL_LST_EN_0804.PDF • PAGE 1
ABuilding Safety. Building Security.
Devices for Hazardous Areas
for the Apollo/Discovery Loop
IS Optical Smoke Detector AOEX-55000-640
• ADM loop technology with
Apollo/Discovery protocol
• Optical smoke detector
• Thermal detector
• Safety barrier with galvanic isolation
• Protocol interface for communication
with the fi re detection control panel
• ATEX certifi ed
Specifi cations
The addressable Intrinsically Safe Optical Smoke De-
tector AOEX-55000-640 (fi g. A) uses the scattered light
principle and was developed for the detection of smo-
ke particles in hazardous areas. The smoke detector
must always be connected via a safety barrier, which
has been approved for this detector, and a protocol
interface. Furthermore, the relevant country specifi c
regulations always have to be observed.
The proven ADM loop technology with Apollo/Discovery
protocol establishes a permanent communication be-
tween the fi re detection control panel and the detector.
That ensures a periodical function testing of the detec-
tor. In the control panel all types of fi res are detected by
continuously comparing fi re patterns.
Intelligent evaluation algorithms use the current condi-
tion of the sensing chamber to predict the likely time
of the next maintenance. Thus the alarm threshold is
automatically adjusted within the permissible range, de-
pending on the contamination. With that, the constant
response sensitivity of the detector is ensured for a
long time.
The two LEDs with 360° visibility indicate the activated
condition of the detector. The detector address is se-
lected by means of a code card in the detector base.
Therefore the detector can be changed without additi-
onal tools.
The detector is inserted into the IS Detector Base ASEX-
45681-215 (not illustrated) and it can be protected
against theft.
Ignition protection intrinsically safe
Ex classifi cation EEx ia IIC T5
Operating voltage Supply through loop voltage
Current consumption typ. 340µA (quiescent)
Ambient temperature -20°C to +40°C (no condensation or icing)
Relative humidity 0 – 95% (no condensation)
Dimensions ø × H 100 × 42 (mm)
Colour white
Weight 100g
fi g. A
fi g. B
fi g. C
fi g. D

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
Ex-ApoDisc_DBL_LST_EN_0804.PDF • PAGE 2
ABuilding Safety. Building Security.
IS Thermal Detector AWEX-55000-440
The addressable Intrinsically Safe Thermal Detector
AWEX-55000-440 (fi g. B) uses the heat principle and
was developed for the fi re detection in hazardous
areas. The heat detector must always be connected
via a safety barrier, which has been approved for this
detector, and a protocol interface. Furthermore, the re-
levant country specifi c regulations always have to be
observed.
The detector is assigned to Class A2S and can be used
up to a room height of 6m. Depending on the parameter
setup in the fi re detection control panel, the detector
can operate either as maximum heat detector with an
alarm temperature of 55°C, or as rate-of-rise heat de-
tector with a maximum temperature of 55°C.
The proven ADM loop technology with Apollo/Discovery
protocol establishes a permanent communication bet-
ween the fi re detection control panel and the detector.
That ensures a periodical function testing of the detec-
tor. Fires are safely detected in the control panel by
continuously analysing the measured values.
The two LEDs with 360° visibility indicate the activated
condition of the detector. The detector address is se-
lected by means of a code card in the detector base.
Therefore the detector can be changed without additi-
onal tools.
The detector is inserted into the IS Detector Base ASEX-
45681-215 (not illustrated) and it can be protected
against theft.
Specifi cations
Ignition protection intrinsically safe
Ex classifi cation EEx ia IIC T5
Operating voltage Supply through loop voltage
Current consumption typ. 300µA (quiescent)
Ambient temperature -20°C to +40°C (Class T5, no condensation or icing)
-20°C to +60°C (Class T4, no condensation or icing)
Relative humidity 0 – 95% (no condensation)
Dimensions ø × H 100 × 42 (mm)
Colour white
Weight 100g
Approval EECS ATEX 0073
LPCB 010p
Order number 242036
Order name IS Thermal Detector/Anal./XP95/Apo AWEX-55000-440
IS Detector Base ASEX-45681-215
The IS Detector Base ASEX-45681-215 is designed to
accommodate intrinsically safe intelligent fi re detectors
Series XP95 for use in ADM loops with Apollo/Discovery
protocol.
Due to its robust multi-wire screw terminals, the detec-
tors can be wired with ease, thus achieving a secure
and durable connection.
The detector address is selected by means of a code
card in the detector base. Therefore the detector can
be changed without additional tools.
The base is designed for surface mounting in hazardous
areas. A mechanical theft protection of the detector can
optionally be activated at the detector base.
Approval EECS ATEX 0073
LPCB 010q
Order number 241024
Order name IS Optical Smoke Detector/Anal./XP95/Apo AOEX-55000-640

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
Ex-ApoDisc_DBL_LST_EN_0804.PDF • PAGE 3
ABuilding Safety. Building Security.
The Protocol Interface API-55000-855 (fi g. D) serves for
the design of an intrinsically safe electric circuit in ADM
loop technology. It allows the bidirectional data traffi c
between fi re detection control panel and detectors in
hazardous areas, via an ADM loop with Apollo/Discove-
ry protocol. The interface is always used together with
the Safety Barrier AES-29600-098.
Protocol Interface API-55000-855
Ignition protection intrinsically safe
Ex classifi cation EEx ia IIC T5
Operating voltage Supply through loop voltage
Current consumption at 24V 1mA
Ambient temperature -10°C to +60°C
Relative humidity 10 – 95% (no condensation)
Dimensions W × H × D 93 × 110 × 20 (mm)
Weight 100g
Order number 228005
Order name Protocol Interface/Anal./XP95/Apo API-55000-855
Specifi cations
Safety Barrier AES-29600-098
The Safety Barrier AES-29600-098 (fi g. C) is used for
intrinsically safe electric circuits. The built-in zener bar-
rier and the safe galvanic isolation allow the connection
of fi re detectors in hazardous areas. Due to the galvanic
isolation, the earth leakage monitoring can remain acti-
vated in the fi re detection control panel.
Ignition protection intrinsically safe
Ex classifi cation EEx ia IIC T5
Operating voltage Supply through loop voltage
Ambient temperature -10°C to +60°C
Colour green
Approval EECS ATEX 0073
Order number 228004
Order name Safety Barrier/Anal./XP95/Apo AES-29600-098
Specifi cations
Ambient temperature -20°C to +60°C (no condensation or icing)
Relative humidity 10 – 95% (no condensation)
Dimensions ø × H 100 × 15 (mm)
Colour white
Weight 50g
Order number 246027
Order name IS Detector Base/Anal./Apo ASEX-45681-215
Specifi cations