Ltech DIN-DMX-350 User manual

DIN-DMX-350
CC DMX/RDM DECODER
1. Product Parameter:
DIN-DMX-350 CC DMX/RDM Decoder DIN-DMX-350 CC DMX/RDM Decoder
1
(DIN Rail, Screw Dual-use)
DIN-DMX-350 CC DMX/RDM Decoder:
Input Signal:
Input Voltage:
Output Voltage:
Max. Load Current:
Max. Output Power:
Dimming Range:
Mounting:
DMX512, RDM
12~48Vdc
3~46Vdc
350mA × 3CH
(1.05W~16.1W) × 3CH Max. 48.3W
0~100%
DIN Rail or Screw
DIN Rail Mounting Size:
Working Temperature:
Dimensions:
Package Size:
Weight (G.W):
Protection:
TS-35/7.5 or TS-35/15
-30℃~55℃
L112×W35×H67(mm)
L114×W37×H70(mm)
135g
Short circuit / Over current
DIN-DMX-350 DIN Rail DMX decoder have 3 digits digital tube to display DMX address, simple
and intuitive read and write DMX address, meanwhile have the self-testing pattern function. With
the standard RDM remote device management protocol, supports DMX512 signal bi-directional
communication, achieves remote management of reading and writing DMX address (DMX master
controller must recognize the RDM protocol).
DIN-DMX-350 can work with DMX512 console; realize 0-100% brightness and various changing
effects, can control single color, bi-color, RGB LED light .
s
2. Product Size:
3. Function Key:
++
--
MM
Running Light
M KEY
The running light flashes quickly when input
DMX signal. Flash frequency depends on
received frame rate. The running light
flashes as usual in free time.
Short press: enter DMX decoder mode.
Long press: enter self-testing scene mode.
3.1 DMX Decoder Mode.
Address Setting:
In DMX Decoder Mode, first press "+" or "-" key to enter address setting. Changing
the DMX initial address when the 3 address value start to flicker. (Range: 001-512)
Long press and key
at the same time, set the
brightness output to linearity
curve (C-L).
Long press and key
at the same time, set the
brightness output to Gamma
curve (C-E)
Long press and key
at the same time, check the
present luminosity curve.
+
-
M
Short press to add one more address, long press to quickly.
Short press to subtract one more address, long press to subtract quickly.
Short press to quit.
add
:
:
:
2
DMX/RDM
signal input
DMX/RDM
signal output
12-48Vdc
power input
LED lamps
connection
www.ltech-led.com

4. Conjunction Diagram:
+
-
Switch changing modes
by pressing key.
+
-
M
3.2 Self-testing Scene Mode.
3.3 Restore the Default Parameter:
Restore the default parameter, digital tube display "RES".
Default Parameters: DMX decoder mode, DMX base address is 1, Gamma curve,
self-testing in No.1 pattern status.
Long press “M” key to enter self-testing scene mode.
Series 1-12pcs LED × 3CH
3
If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W
90-120Ω terminal resistor at the end of each line.
An amplifier is needed when more than 32 decoders are connected, signal amplification should not be
more than 5 times continuously.
4Update Time: 2017.12.19_A1
5.1 The product shall be installed and serviced by the qualified person.
6.4 Any amendment or adjustment to this warranty must be approved in writing by our company only.
6.3 Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
We shall not be liable for any incidental or consequential damages for breach of any stipulation in
this warranty.
6.1 We provide lifelong technical assistance with this product:
For faults beyond the 5-year warranty, we reserve the right to charge for time and parts.
A 5-year warranty is given from the date of purchase. The warranty is for free repair or replacement
if cover manufacturing faults only.
The product appears to have excessive physical damage.
Damage due to natural disasters and force majeure.
Warranty label, fragile label and unique barcode label have been damaged.
The product has been replaced by a brand new product.
6.2 Warranty exclusions below:
Any man-made damages caused from improper operation, or connecting to excess voltage and
overloading.
5.6 If a fault occurs, please return the product to your supplier. Do not attempt to fix this product by
yourself.
5.5 Ensure all wire connections and polarities are correct before applying power to avoid any damages to
the LED lights.
5.5 Please ensure that adequate sized cable is used from the controller to the LED lights to carry the
current. Please also ensure that the cable is secured tightly in the connector.
5.4 Please check if the output voltage of the LED power supplies used comply with the working voltage of
the product.
5.3 Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
5.2 This product is non-waterproof. Please avoid the sun and rain. When installed outdoors, please
ensure it is mounted in a water proof enclosure.
5. Attention:
6. Warranty Agreement:
★This manual only applies to this model. We reserve the right to make changes without prior notice.
DIN-DMX-350 CC DMX/RDM Decoder DIN-DMX-350 CC DMX/RDM Decoder
*
*
NO.
MODE
P-1
P-2
P-3
P-4
P-5
P-6
P-7
P-8
P-9
1
2
3
4
5
6
7
8
9
Digital Tube Display
(press +/- to switch)
Long press keys at the same time,
www.ltech-led.com
Static Red
Static Green
Static Blue
Static Yellow
Static Purple
Static Cyan
Static White
7 Color Jumping
7 Color Smooth