Ltech LT-840-6A User manual

Input Signal: Input Voltage: Current Load: Output Power: DMX512 Socket: DMX512, RDM5~24Vdc6A × 4CH Max. 24A(0~30W...144W) × 4CH Max. 576W3-pin XLR, RJ45, Green Terminal LT-840-6ADimming Range: Protection:Working Temp.: Dimensions: Package Size: Weight (G.W.): 0~100%Short circuit / Over current-30~65L156 × W78 × H40(mm)L180 × W82 × H48(mm)445g℃℃LT-840-6ADMX/RDM 4CH CV DECODER LT-8406A DMX/RDM 4CH CV Decoder-LT-840-6A wcommunication, achieves remote management of reading and writing DMX address (DMX master controller must recognize the RDM protocol). Equipped with DMX standard 3-pin XLR, RJ45, green terminal interface. Realize 0-100% dimming or different lighting effect; workable with single color, bi-color, RGB or RGBW LED lamps.ith the standard RDM remote device management protocol, supports DMX512 signal bi-directional 1. Product Parameter:12. Product Size:3. Configuration Diagram:Power Input SocketAddress Dip SwitchGreenTerminal(with amplifier function)40mm78mm156mm146mm
12345678910ONDIP
3-pin XLRRJ45ABNNNNGG
LED LampsConnection SocketLT-840-6A DMX/RDM 4CH CV Decoder4.3 DMX Dimming Instruction: Dip Switch Operation:4.RDM Mode: The dip switch 1-10 are OFF.
FUN = ON (the 10th dip switch = ON)
Self-testing Mode: FUN = OFF (the 10th dip switch = OFF) DMX Mode: Setting DMX addresses with dip switch 1-9 FUN = OFF (the 10th dip switch ) Mode= OFFDMX
4.1 How to set DMX address via dip switch:E.g.1: Set Initial Address To 32.E.g.2: Set Initial Address To 37.E.g.3: Set Initial Address To 178.001+004+032=37002+016+032+128=178444111111222222333333444444555555666666777777888888999999ONONONDIPDIPDIP010101OFFONOFFONOFFONOFFONOFFONOFFON101010101010ONDIPONONDIPDIP4.2 Self-testing Mode: DMX address value = the total value of (1-9), to get the place value when in “on” position, otherwise . will be 0
FUN=ON (the 10th dip switch = ON) Self-testing Mode
1=on4on=7on=8on=9on=2on=5on=3on=6on=
Self-testFunction
-19=off
Dip Switch
Static BlackStatic RedStatic RedStatic GreenStatic GreenStatic BlueStatic BlueStatic YellowStatic YellowStatic PurpleStatic PurpleStatic CyanStatic CyanStaticWhiteStaticWhite7 Colors Jumping7 Colors Jumping7 Colors Smooth7 Colors Smooth
[Attn] When several dip switches are on, subjected to the highest switch value. As the figure above shows, the effect will be 7 colors smooth at 7 speed level.For changingeffects (DipSwitch89 = on): /DIP switch 1-7 is used to realize 7 speed levels. (7 = on, the fastest level)OFFON
12345678910
CH4 0-255PWM LED W)0-100% (CH4CH1 0-255CH2 0-255CH3 0-255Each LT-8406A DMX decoder occupied 4 DMX addresses when connecting the DMX console. -PWM 0-100% (LED R)PWM LED G)0-100% (PWM LED B)0-100% (CH1CH2CH3DMX ConsoleDMX DecoderE.g., the defaulted initial address is 1, please find their corresponding relationships in the form.2www.ltech-led.comwarranty5 years

5. Wiring Diagram: LT-840-6A is equipped with 3 types DMX terminals for users’ selection.
The diagram takes 3-pin XLR terminal as a example, same connecting method for the rest two: green terminal (with amplifier function) & RJ45 terminal.
12345678910ON
LT8406A--
12345678910ON
LT8406A--
DC+DC+
DC
-
DC
-
5-24Vdc5-24VdcInput powerInput power
DMX/RDM signal
12345678910ON
LT8406A--
DMX/RDM signal
DC+
DC
-
5-24VdcInput power
DMX/RDM signal
132
PUSH
132
PUSH
DMX console* resistor at the end of each line. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120Ω terminal 35.1 Decoder can be connected to a variety of standard DMX512 devices:* An amplifier is needed when more than 32 decoders are connected, signal amplification should not be more than 5 times continuously.* signal amplification should be no more than 5 times continuously.Amplified the signal by AMP interface which connecting too many decoder and in overlong signal line, Update Time: 2018.07.06_A56. Attention:
7. Warranty Agreement:
6.1 The product shall be installed and serviced by the qualified person.6.2 This product is non-waterproof. Please avoid the sun and rain. When installed outdoors please mounted in a water proof enclosure. ensure it is 6.3 Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.6.4 Please check if the output voltage of the LED power supply used comply with the working product. voltage of the 6.5 Please ensure that adequate sized cable is used from the controller to the LED lights to carry Please also ensure that the cable is secured tightly in the connector. the current. 6.6 Ensure all wire connections and polarities are correct before applying power to avoid any damages LED lights. to the 6.7 If a fault occursplease return the product to your supplier. Do not attempt to fix this product by , yourself.
7 1 We provide lifelong technical assistance with this product:.A 5-year warranty is given from the date of purchase. The warranty is for free repair or replacement if cover manufacturing faults only. For faults beyond the 5-year warranty, we reserve the right to charge for time and parts.7.2 Warranty exclusions below:Any man-made damages caused from improper operation, or connecting to excess voltage and overloading.The product appears to have excessive physical damage.Damage due to natural disasters and force majeure.Warranty label, fragile label and unique barcode label have been damaged.The product has been replaced by a brand new product.7.3 7.4 only. Any amendment or adjustment to this warranty must be approved in writing by our company★ This manual only applies to this model. reserve the right to make changes without We prior notice.Repair or replacement as provided under this warranty is the exclusive remedy to the customer. We shall not be liable for any incidental or consequential damages for breach of any stipulation in this warranty.4LT-8406A DMX/RDM 4CH CV Decoder-LT-840-6A DMX/RDM 4CH CV Decoderwww.ltech-led.com
RGBW
R3R4R2R1
RGBW
R3R4R2R1
RGBW
R3R4R2R15.2 The connection diagram of three DMX terminals:5.3 The connection diagram of :AMP signal amplifier terminal3-pin XLR Connected in ParallelGreen Terminal Connected in ParallelRJ45 Connected in ParallelThese 3 terminals can be connected in a mixed way.Terminal resistorTerminal resistorTerminal resistorDMX signal input
12345678910ON12345678910ON12345678910ON
12345678910ON12345678910ON12345678910ON
1
12
23
34
45
56
67
78
89
910
10 ON
ON 1
12
23
34
45
56
67
78
89
910
10 ON
ON 1
12
23
34
45
56
67
78
89
910
10 ON
ON
AMPTerminal resistorTerminal resistor
12345678910ON12345678910ON12345678910ON