Ltl Acorn Ltl-5310 Series User manual

Ltl Acorn
Mobile Scouting Camera
Ltl-5310 Series
SMS remote control
720P video

USER’S MANUAL
TABLE OF CONTENTS
General Information.........................................................................................1
1.1 Features.................................................................................................1
1.2 Application............................................................................................. 2
1.3 Illustration.............................................................................................. 2
Quick Start........................................................................................................5
2.1 Insert SIM Card..................................................................................... 5
2.2 Load Batteries........................................................................................5
2.3 Insert SD Card.......................................................................................6
2.4 Enter Test Mode.....................................................................................6
2.5 Enter Live Mode.....................................................................................7
2.6 Advantages of Prep Sensors.................................................................8
Advanced Settings......................................................................................... 9
3.1 Parameter Settings.............................................................................. 9
3.2 File Format........................................................................................... 12
3.3 Set up Camera on PC......................................................................... 12
3.4 Set up MMS Function on PC............................................................... 15
3.5 SMS remote control............................................................................. 17
3.6 Camera Working with MMS................................................................. 21
3.7 View Local MNOP Name and Signal Strength on TFT display........... 22
Ltl-5310 Series Products............................................................................... 24
4.1 Parts.................................................................................................... 24
4.2 Models for Purchase............................................................................ 24
Important Information.................................................................................... 24
5.1 Prevent From Short-Circuits................................................................ 24
5.2 Power Supply and Battery Box............................................................ 25
5.3 SD Card............................................................................................... 25
5.4 AutoAdjustment on Video Length........................................................ 25
5.5 850nm and 940nm IR LED.................................................................. 26
5.6 Mount on Tripod................................................................................... 26
5.7 FAQs on MMS Function...................................................................... 27
Firmware Upgrades....................................................................................... 28
6.1 Firmware Upgrades............................................................................. 28
Warranty Information..................................................................................... 29
Appendix I Technical Specifications............................................................ 30
Appendix II Package Contents..................................................................... 31
Appendix III Instruction on Installing Battery Box..................................... 32

1
GENERAL INFORMATION
Introduction
The Ltl Acorn 5310 Series (Model Ltl-5310A/MC and Ltl-5310MM) is the third
generation of our Ltl acorn scouting camera. Bundled with the MMS-module
(Multimedia Messaging Service) battery box (Part # LTL-MM1)standard
scouting camera (Part # Ltl-5310MC) can be upgraded to work as a remote
cellular camera. With its highly sensitive Passive Infra-Red (PIR) sensor the
cameradetects the sudden change of ambient temperature caused by
moving game in a region of interest (ROI), triggers to take pictures/videos,
and sends the images via GSM network to the user’s cell phone or email
account. Withnewly added SMS remote control feature you can change the
related menu of the camera by sending SMS order to the camera in the
specific form of the SMS content.
1.1 Features:
Programmable 5 or 12-Megapixel high-quality resolution.
With SMS RCP (remote control program) parameters of camera can
be changed by SMS sending. If in request, the camera can take
picture and send back simultaneously.
No-glow Infrared 940nm LEDs flash range as far as 65 feet, luminance
as bright as 850nm.
In “Cam + Video” mode, camera takes both pictures and video at every
triggerevent
Ultra low standby power consumption. Extremely long in-field life (in
standby mode, up to 6 months with 8 x AA batteries)
Unique side Prep Sensor design provides wider sensing angle and
enhances camera’s response speed
Perform in the most extreme temperatures from -22°F to 158°F
Compact size (5 ½ x 3 ½ x 2 ½ inches). Well designed to deploy
covertly
Impressively quick trigger time (0.8 second)
In Time Lapse setting, the camera automatically and constantly takes
pictures/videos at specified interval. This is very useful when observing
plants flowering, birdsbuilding nest, or when monitoring unattended
properties such as parking lots
With Timersetting on,the camera can be programmed to only work in
specified period every day. This feature can work together with Time
Lapse feature
Backpack-looking tree grabber makes mounting and aiming a snap

2
Serial Number setting enables you to code locations in the photos. This
helps multi-camera users identify the location when reviewing the
photos
Built-in 2 ¼” TFT color display to review images and videos
Date, time, temperature and moon phase can be stamped in the
pictures
Lockable and password protected
MMS image sizes: 640 x 480
Users can configure the Camera and MMS function either by running
the enclosed CD on the computer, or directly on the built-in TFT display.
Separation of the Camera and the MMS module provides users
flexibility: starting with the value model as a standard scouting camera,
and upgrading to the premium model with MMS function.
If local area mobile signal is bad , Could not send MMS, Also can choose to
send a text message(SMS). Message content is taking pictures time and
Camera serial number.
Our Advanced Remote Cellular Technology transmits images to your
cell phone and email account constantly at lower battery consumption
and shorter transmission time, compared to products of its kind on the
market.
Automatically send text alert when battery power level goes low
Check cellular signal information on the built-in TFT display in the field
All MMS pictures saved in SD card as well as the original ones
Internal antenna design makes the camera portable while still emitting
strong signal
Operates globally via GSM/GPRS network. Supports four bands: 850 /
900 / 1800 / 1900MHz.
1.2 Application
Trail camera for hunting
Animal or event observation
Motion-triggered security camera, for home, office and community
All other indoor/outdoor surveillance where invasion evidence needed
1.3Illustration
Figure 1.1 shows the front view of the camera (Part # Ltl-5310M)
Figure 1.2 shows the bottom view of the camera (Part # Ltl-5310M)
Figure 1.3 shows the back view of the camera (Part # Ltl-5310M) and
front view of the battery box (Part # LTL-BM1 or LTL-MM1)

3
Figure 1.1: Front View of Ltl-5310M
Figure 1.2: Bottom View of Ltl-5310M
LED IR
Flash
Lens
Main
Light
Sensor
Motion
Indicator
PIR
Sensor
Prep
PIR
Sensor
Lock
Hole

4
The camera provides the following connections for external devices: USB 2.0
port, SD card slot, TV out jack, and external DC power in jack. The 3-way
Power/Mode Switch is used to select the main operation modes: OFF,ON
and TEST.
To power up the camera, install four NEW high-performance alkaline or
lithium AA batteries in the camera. FOR BETTER PERFORMANCE, WE
RECOMMEND USING ENERGIZER LITHIUM AA BATTERIES. To achieve
longer in-field life, always install the additional battery box which contains four
more AA batteries. (Please reference Appendix III: Instruction on Installing
Battery Box)
Figure 1.3: Back View of Ltl-5310M and Front View of Battery Box
CAUTION: If you are not using the camera for an extended period of
time, it is highly recommended that you remove the batteries from the
camera to avoid possible acid leak that may damage the camera which
would void the warranty.

5
QUICK START
2.1 Insert SIM Card (Only for Model Ltl-5310MM)
You need to purchasethe SIM card
from your local Mobile Phone
Network Operators(MPNO),
making sure they provide
Multimedia Messaging Service
(MMS). Ask them for the relevant
information to configure the MMS
settings on your camera.(Please
reference 3.4 Set up MMS
Function on PC in the Advanced
Operation section.)
Open the battery compartment
cover, slide the SIM card in the slot
and lock it. Figure 2-1 MMS-module Battery
Box
2.2 Load Batteries
To install batteries on the camera (Part # Ltl-5310M), please follow the
instructions below.
Open the bottomcover by pulling down the lock hole.
Push the cover of thebattery compartment and release. It will pop out.
Install 4 AA batteries. Make sure the polarity matches the sign on the
cover.
Replace the cover.
To install the additionalbattery box (Part # LTL-BM1 or LTL-MM1), please
reference Appendix III: Instructions on Installing Battery Box)
Alternatively the camera can run on an external 6V~12V DC power source
(optional). When bothexternal power and batteries are connected, the
camera will be powered by the external one preferentially. Bundled with our
external solar power supply (purchased separately), the camera can work in
the field over one year without changing batteries.

6
When battery level gets low, the Motion Indicator in the LED array will flash
blue. On Model Ltl-5310MM, a “Battery Low” text alert will be sent
automatically to the user’s cell phone or email account.
2.3 Insert SD Card
The camera does not come with internal memory. So it will not work without
a SD (Secure Digital) memory card or SDHC (High Capacity) card. Before
inserting the SD card into the card slot, please make sure the write-protect
switch on the side of the SD card is “off” (NOT in the “Lock” position). The
supported memory capacity is up to 16GB. If you use a card capable of
above 16GB, make sure you test it before putting the camera in use.
Figure 2-2
CAUTION: ALWAYS SWITCH THE CAMERA TO OFF MODE BEFORE
YOU INSTALL OR REMOVE THE BATTERIES OR THE SD CARD.
2.4 Enter Test Mode
Switch to the TEST position to enter the Test mode. In this mode you can
take pictures or video clips like a regular digital camera, or enter the Menu to
set up parameters. On the keypad there are four “shortcut” functional keys
(see Figure 2-3) working as below:
Figure 2-3
Press the key to set the camera to shoot video clips.

7
Press the key to set the camera to take still pictures.
Press the SHOT key to manually trigger the shutter. A photo or
video (depending on the camera setting) will be taken and saved to
the SD card. If the display shows “CARD PROTECTED” when you
press the SHOT key, switch the power OFF, remove the SD card and
slide its write-protect switch to off.
Press the REPLAY key to review/playback photos/videos on the
LCD screen, or a connected TV monitor. Use and key to
navigate.
There is another key, MENU, on the keypad that allows you to program the
camera to work the way you want. Please make reference to 3.1 Parameter
Settings in the Advanced Operation section.
Under the test mode, one useful function you would like is testing the work
area of the PIR (Passive Infrared) sensor, specifically the sensing angle and
distance. To perform the test:
First strap the camera on a tree aiming the region of interest (ROI).
Walk slowly from one side of the ROI to the other parallel to the
camera. Try different distances and angles from the camera.
If the Motion Indicator flashes blue, it indicates the position from
where you are detected by one of the side Prep PIR sensors. If the
Motion Indicator flashes red, it indicates the position from where you
are captured by the main PIR sensor.
By doing this test, you can find the best placement when mounting and
aiming the Ltl Acorn camera. In general, you are recommended to place the
camera 3 to 6 feet (1 to 2 meters) above the ground.
To avoid potential false triggers due to temperature and motion disturbances,
please do not aim the camera at a heat source (i.e. the sun) or nearby tree
branches and limbs. The ideal direction to aim at is North or South. Also,
remove any limbs close to the front of the camera.
2.5 Enter Live Mode
Switch to the ON position to enter the live mode. The Motion Indicator will
flash red for about 10 seconds and the camera starts working by itself
without any manual handling. It will at once shoot pictures or record videos
when game or other objects enter the PIR area of the main sensor directly. If
the game enters the PIR area of the prep sensors from the side, the prep
sensors detect the movement and activate the camera. While the game
keeps moving into the PIR area of the main sensor, the camera takes
photos/videos immediately. If the game roams away after entering the PIR

8
area of the prep sensors, the camera will power off and enter standby mode.
2.6 Advantages of Prep Sensors
In general, to save battery power, an Infer-Red camera is in “sleep” mode,
with only the PIR sensor working. When game is detected by the PIR sensor,
the camera is powered on and starts shooting pictures. The time period from
being activated to starting firing is called trigger time. The trigger time varies
among different scouting camera brands in the market, generally from 1 to 5
plus seconds. Our Ltl Acorn scouting camera has an impressive 0.8 second
trigger time. However, when game passes across very quickly, the picture
may only capture the rear part of the body, and possibly nothing at all.
With the unique side prep PIR sensors design, our Ltl Acorn solves this issue.
The combination of the two side prep sensors and the main sensor comes
up with a 100 to 120° angle of induction, a very wide scope far outweighing
the 50 ° angle of the camera lens. When game first crosses the PIR area of
the prep sensor, the camera is activated and ready to shoot after 1 second. If
the game continually enters into the PIR area of the main sensor, the camera
takes pictures immediately, therefore catching the whole body of the game.
This split-second process could be as short as 0.2 second.
In the case the game browses only in the PIR area of the prep sensors, to
avoid the camera being powered on constantly, the system is designed to
work in the following way: If the game does not enter the PIR area of the
main sensor and therefore not trigger the main sensor, the camera will power
off after 3 seconds. If the trigger events consecutively happened twice only in
the PIR area of the prep sensors, the camera will not be activated by the
side prep sensors, but only by the main sensor. So later on when the game
enters the PIR area of the main sensor eventually, since it is not in fast
movement, the picture will by all means capture the whole body of the game
based on our standard 0.8 second response time.

9
ADVANCED SETTINGS
The Ltl Acorn trail camera comes with preset manufacturer settings. You can
change the settings to meet your requirements. Please make sure the camera
is in the test mode.
3.1 Parameter Settings
Press “MENU” key to enter/exit the menu. Press , to move the marker,
, to
change the setting, and to confirm the change. Always remember to press
to save
the change. Otherwise you will lose your new setting.
Parameter Settings
(Bold = default)
Description
Mode Camera,
Video,
Cam+Video
Select whether still photos or video
clips are taken. In Camera+Video
mode, camera first takes photos and
then shoots videos immediately.
Format Enter All files will be deleted after
formatting the SD card. Highly
recommend you format the SD card
if it has been used previously on
other devices. Caution: make sure
wanted files on the SD card have
been backed up first!
Photo Size (affects
still photos only)
5MP, 12MP, 1.3MP Select desired resolution for still
photos from 1.3 to 12 megapixels.
Higher resolution produces better
quality photos, but creates larger
files that take more of the SD card
capacity. Besides, larger files require
longer time to write to the SD card,
which will slightly slow the shutter
speed. 5MP is recommended.
Video Size (affects
video clips only)
1280x720
640×480
320×240
Select video resolution (pixels per
frame). Higher resolution produces
better quality videos, but creates
larger files that take more of the SD
card capacity. 640×480 is VGA mode
in standard 4:3 format.

10
Set Clock Enter Press Enter to set up date and time.
Internal capacitor will retain the clock
time for up to 7 minutes when
changing batteries.
Picture No. (affects
still photos only)
01 Photo, 02 Photos,
03 Photos
Select the number of photos taken in
sequence per burst in Camera mode.
Please also refer to the Interval
parameter.
Video Length
(affects video clips
only)
Avi 10 s, optional
from 1s to 60s
Videos are in AVI format that can be
played back on most media players.
Interval 1 Min, optional from
1S to 60M
Select the length of time that the
camera will wait from when the last
picture was taken and written in the
SD card, until it responds to any new
triggers from the PIR sensor. During
the selected interval, the camera will
not take pictures/videos. This
prevents the SD card from filling up
with too many redundant images.
Sense Level High, Normal, Low,
Off
Select the sensitivity of the PIR
sensor. The High setting suits
indoors and environments with little
interference, while the Normal/Low
suits outdoors and environments with
more interference, Off which turns
the function off. Temperature also
affects the sensitivity. The High
setting is suitable when the ambient
temperature is warm, and the Low
setting is helpful in cold weather.
Time Stamp (affects
still photos only)
On, Off Select On if you want the date & time
imprinted in every photo.
Timer 1 Off, On Select On if you only want the
camera to work within a specified
time period every day. For instance,
if the starting time is set at 18:35 and
the ending time at 8:25, the camera
will function from 18:35 the current
day to 8:25 the next day. Outside the
time period the camera will not be
triggered or take photos/videos. This
feature can be used together with
Time Lapse feature.

11
Timer 2 Off, On Select On if you only want the
camera to work within a specified
time period every day. For instance,
if the starting time is set at 18:35 and
the ending time at 8:25, the camera
will function from 18:35 the current
day to 8:25 the next day. Outside the
time period the camera will not be
triggered or take photos/videos. This
feature can be used together with
Time Lapse feature.
Password Set Off, On Set up a password to protect your
camera from unauthorized users.
Serial No. Off, On Select On to assign a serial number
to each camera you have. You can
use the combination of 4 digits
and/or alphabets to record the
location in the photos (e.g. YSP1 for
Yellow Stone Park). This helps multi-
camera users identify the location
when reviewing the photos.
Time Lapse Off, On If set On, the camera will
automatically take photos/videos at
the set interval (Note: in this mode,
the PIR sensor is disabled). This is
helpful when observing cold-blooded
animals like snakes, or the process
of flowering, etc. This feature can
work together with Timer feature.
Side PIR On, Off The default setting is On. The two
side prep PIR sensors provide wider
sensing angle and enhance
response time. (Reference 2.5
Advantages of Prep Sensors.)
However, in some situations you
have difficulty removing the
interfering branches, or avoiding the
sunlight. If so, you have the option to
turn off the side sensors.
MMS Phone No. Enter Press Enter to input the phone
number you want to send MMS to.
To input more phone numbers, or to
set up email accounts, reference 3.4
Set up MMS Function on PC.

12
3.2File Format
The SD card stores all original pictures and videos in the folder
\DCIM\100IMAGE, and all MMS pictures in the folder
\DCIM\MMS\100IMAGE with the same filename. Pictures are saved with
filenames like IMAG0001.JPG and videos like IMAG0001.AVI.
In the OFFmode, youcan use the provided USB cable to download the files
toacomputer. Or you can put the SD card to a SD card reader, plug in a
computer, and browse the files on the computer without downloading.
The AVI video files can be played back on most popular media players, such
as Windows Media Player,QuickTime, etc.
3.3Set up Camera on PC
You can set up your camera and/or MMS function on your home PC. Run the
Setup.exe file on the enclosed CD
. You can also visit the national
distributor’s website to download the program, or download
In the submenu, you can set the
daily number of pictures sent via
MMS.0stands for Unlimited.1-
99/Day gives you flexibility sending
up to 99 pictures per day
SMS remote control 0, 1~24, Off represents the SMS receipt time, “0”
indicates 10mins, “1~24” indicates
the interval time 1~24h to receive
SMS, “off” which turns the SMS
remote control function off.
MMS Status Off, VGA, SMS The default setting is Off, which
turns the MMS function off. To turn it
on, choose either VGA or SMS. VGA
is to send 640x480 pictures, where
SMS text messages (date & time)
Default Set Press OK Enter to return all your
camera settings back to the
manufacturer default. However, all
the MMS function settings will remain
except for MMS Phone No. and
MMS Status.

13
from http://www.sendspace.com/folder/7zd6ic
The following window prompts:
Click on Camera Setup, and you will see the following interface:

14
Set up the camera based on your need. Click on to retrieve the
computer time. Click on to choose the directory to save your
settings, usually undertheroot directory of the SD card (You need to insert the
SD card in the SD card reader and plug it in your computer.) Then, click on
. A file named menu.dat will be created and saved in the directory
you just selected. If you selected a directory other than the SD card, you need
to move themenu.dat file to the root directory of the SD card before inserting
the card in the camera lateron.
If you like, you can usethemanufacturer default settings by clicking on
.
At this point, if your camera is Model Ltl-5310MM, or you’ve just upgraded your
standard scouting camera,Model Ltl-5310MC, to Model Ltl-5310MM by
Getime
Select
Generate
Defanlt

15
purchasing the MMS-module battery box (Part # LTL-MM1), skip the following
step and go directly to 3.4 Set up MMS Function on PC. If your camera is
Model Ltl-5310MC, the standard scouting camera, you’re done with the
camera setting. Click on Exit to exit the interface.
Retrieve the SD card from the computer and insert it in the camera. Switch to
the TEST position to enter the TEST mode. A message will show up on the
TFT display, indicating the Camera has been successfully set up. You are set
with the camera.
ATTENTION: THE PASSWORD CAN ONLY BE SET UP ON THE CAMERA,
NOT ON THE PC.
3.4Set up MMS Function on PC
After you click on Exit on the Camera Setup interface, the following window
prompts again:
Click on MMS Setup, and you will see the following interface:

16
First, you need to choose how you like to set up the MMS Mode
--Auto or Manual. If you choose Auto, then you need to
choose the country and the Mobile Phone Network
Operator (MPNO). After doing that, the below section will populate with
parameters pertaining to the selected MPNO, such as URL, APN, Gateway
and Port. Then you can input the phone number and email address you’d like
the MMS pictures to be sent to. You can enter up to three different phone
numbers or email address.

17
If you choose Manual to manually input all the parameters, you need to
contact your Mobile Phone Network Operator (MPNO) to have them provide
you all the required information.
Note: Because each local MPNO has their own settings for their MMS service,
and those settings can change over time, we recommend you verify all the
settings with your MPNO, even you choose Auto to let the system to configure
the settings. We pre-store those settings for each major MPNO in the program
on the enclosed CD. If you find out those settings have changed according to
the information provided by your MPNO, or you have settings from your MPNO
that is not on our Operators list, please notify us so we can update our program.
Click on to
Select choose the directory to save the settings, usually under
the root directory of the SD card (You need to insert the SD card in the SD card
reader and plug it in your computer.) Then, click on . A file named
menu.dat will be created and saved in the directory you just selected. If you
selected a directory other than the SD card, you need to move the menu.dat
file to the root directory of the SD card before inserting the SD card in the
camera later on.
Click on Exit to exit the MMS Setup interface. Retrieve the SD card and insert
it in the camera. Switch to the TEST position to enter the TEST mode. A
message will show up on the TFT display, indicating the MMS function has
been successfully set up. Congratulations! You camera (Model Ltl-5310MM) is
all set to send color pictures to your cell phone and/or email account every time
it is triggered.
3.5SMS remote control
Definition
All the SMS content starts with LTL(ltl), ends with AA(aa).
All the order code which needs to be changed indicated by 2 figures
Order
code Function code example meaning
01 Mode camera 0 video 1 camera+
video 201*1# Set to video
mode
02 Image size 5MP 0 12MP 1 1.2MP
202*1# 12MP
DSP SMS receipt content
Generate

18
03 Video size VGA(0), QVGA (1) 03*1# QVGA
04 Picture No 01 photo 0 02 photo 1
03 photo 2 04*2# 3 photos
05 Video length 1-60 indicates different value 05*59# 59s
06
Interval beginning with S s represents
Second, with M m represents minute 1-60
indicates different value
06*s30# Interval:30s
07
Serial No off 0 on 1 take camera
setting for reference
figure+ letter
07*1AbC
D#
Serial number:
AbCD
08 PIR sense level Low 0 normal 1 High
2 , off (3) 08*1# normal
09 Time Stamp off 0 on 1 09*0# off
10 Side PIR off 0 on 1 10*1# on
11 MMS status off 0 VGA 1 SMS 2 11*2# SMS
12 Phone No 2 or Email Maximum 48 types 12*15197
611542#
Phone number
15197611542
13 Phone No 3 or Email Maximum 48 types
13*info@l
tlacorn.cn
#
Email
[email protected]
n
14 Email Maximum 48 types
14*info@l
tlacorn.cn
#
Email
[email protected]
n
15 Maximum photo number setting 0 no limit 15*0# No limit
16
Time lapse off 0 on 1 Time indicated
with 2 bytes, EX 1h 33m 2s indication: 01
33 02.
16*10133
02#
1h33m2s
shooting a set
of specified
image
17 Timer 1 off 0 on 1 . Time indicated with
2 figures, EX 1h 33m indication: 01 33.
17*10133
0200# 1h 33m~2h
18 Timer 2 off 0 on 1 . Time indicated with
2 figures, EX 1h 33m indication: 01 33.
18*10133
0200# 1h 33m~2h
19 SMS receipt time 0-24h 0 indicates no
limit 25 off 19*25# Off
60
Shooting or not for this time off 0
on 1
(After the receipt of the order by camera
module, there will be a picture be shot and
sent back to your phone/MMS or
email/GPRS)
60*1# Shoot and return
Order 12 and13are ineffective in SMTP
mode
,720P