LTS VSIP7643W-SZ User manual

Network Fixed Dome Cameras
Quick Guide

1
Safety and Compliance Information
Installation and removal of the unit and its accessories must be carried
out by qualified personnel. You must read all of the Safety Instructions
supplied with your equipment before installation and operation.
Installation
This device is a class A product and may cause radio interference.
Take measures if necessary.
Be careful not to blur, scratch, damage the dome cover or leave
fingerprints on it because this could decrease image quality. Keep
the protective film on the dome cover until installation is
complete.
Make sure the camera operates in an environment where the
temperature and humidity meet requirements. Keep the camera
from excessive pressure, vibration, moisture, dust, and intensive
electromagnetic radiation.
Use a power adapter or a PoE device that meets requirements.
Otherwise, the device may be damaged.
Make sure the length of the power cable between the power
adapter and the camera is not too long, otherwise the voltage of
the camera is lowered, causing the camera to work abnormally. If
it is required to lengthen the power cable, lengthen the cable
between the power adapter and the mains.
Do not hold the tail cable by hand for weight bearing. Otherwise,
the cable connector of the camera could be loosened.
When connecting to an external interface, use an existing
connection terminal, and ensure that the cable terminal (latch or
clamp) is in good condition and properly fastened. Ensure that the
cable is not tense during mounting, with a proper margin reserved
to avoid poor port contact or loosening caused by shock or shake.
The connectors of the tail cable must not be exposed. The bar
cavity, waterproof box, corrugated pipe and PVC pipe must be
fully sealed to protect the connectors from water. The waterproof

2
components for the RJ45 plug must be used properly to protect
the network cable from water.
Make sure the wall or ceiling is strong enough to support the
weight of the camera. If dust falls during mounting, take off the
dome cover and keep it away from dust. Install the dome cover
after the base is installed.
Purchase a bracket if you need to increase the field of view.
Contact your local dealer for details.
Contact professionals for maintenance information. Do not
attempt to dismantle the device by yourself. We shall not assume
any responsibility for problems caused by unauthorized repair or
maintenance.
Maintenance
Caution: There will be risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
If there is dust on the lens or the transparent dome cover, remove
the dust gently using an oil-free brush or a rubber dust blowing
ball.
If there is grease on the lens, remove the grease using lens
cleaning cloth gently and then clean the lens in a circular spiral
from the center outward using lens cleaning cloth dipped with
small amount of cleaning solution. If the grease still cannot be
removed, use oil-free cloth or lens cleaning paper and clean the
lens gently until it is removed.
If there is grease or a dust stain on the transparent dome cover,
clean the cover gently from the center outward using lens cleaning
cloth. If the grease or the stain still cannot be removed, use lens
cleaning cloth dipped with detergent and clean the dome cover
gently until it is removed.
Do not use organic solvents, such as benzene or ethanol when
cleaning the transparent dome cover.

3
Make sure the lens cleaning cloth is clean itself.
Never look at the transmit laser while the power is
on. Never look directly at the fiber ports and the
fiber cable ends when they are powered on.
Use of controls or adjustments to the performance
or procedures other than those specified herein
may result in hazardous laser emissions.
Regulatory Compliance
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

4
LVD/EMC Directive
This product complies with the European Low Voltage
Directive 2014/35/EU and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the
Waste Electrical & Electronic Equipment (WEEE)
Directive and must be disposed of in a responsible
manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery
Directive 2013/56/EC.For proper recycling,return the
battery to your supplier or to a designated collection
point.
Default IP, Username and Password
Default IP address: 192.168.1.13
Default username: admin
The default password is used for your first login. To
ensure account security, please change the password
after your first login. You are recommended to set a
strong password (no less than eight characters).
Packing List
Contact your local dealer if the package is damaged or
incomplete. The attachments may vary with models, please
see the actual model for details.
Item
Quantity

5
Item
Quantity
Camera
1
User document
1
Accessory pack
1
Appearance
Dimensions
The figures in the manual are for your reference only. The
actual appearance may vary with the product model.
Type A
99.9mm
(3.93")
Ø89.3mm
(3.52")
Ø 128.1mm
(5.04")
Type B

6
99.9mm
(3.93")
Ø89.3mm
(3.52")
Ø 128.1mm
(5.04")
Cable Connection
The appearance and tail cable may vary with device model.
The following examples show cables that are for 12 VDC.( for
cameras with cable)
1
234
No.
Description
No.
Description
1
Audio input/Audio
output/GND
2
Power interface

7
No.
Description
No.
Description
3
Ethernet interface
4
Alarm input/GND
/ Alarm output(N,P)
For specifications, see the latest product datasheets.
Internal Structure
Network
interface
Power
interface
Micro SD
Card slot
c
cReset
button
Transparent
dome cover
Safety wire
1 2 3 5 64 8 7
No.
Description
No.
Description

8
No.
Description
No.
Description
1
ALARM_OUTPUT_
N
2
ALARM_OUTPUT_P
3
GND
4
ALARM_INPUT
5
GND
6
AUDIO_IN
7
GND
8
AUDIO_OUT
Use a pin to press and hold the Reset button for about
15 seconds to restore factory default settings.
Perform this operation within 10 minutes after the
device is powered on or the reset will fail otherwise.
Mount Your Camera
Ceiling Mount
The following part takes ceiling mount as an example. Wall
mount is similar to ceiling mount and therefore is omitted
here. The figures are for your reference only.

9
1. Locate the holes, drill holes on the ceiling, and then mount
the plastic rivets of self-tapping screws. See template for
right direction of logo and tail cable.
2. Install network cable (for cameras without cable).
1
2
Push the network cable
head into the tapered
sleeve.
Cut a hole on the waterproof
rubber stopper, and insert the
network cable head through
the opening.
3Remove the tapered sleeve.
4Connect the network cable to the
network interface, and attach the
rubber stopper to the interface for
water proofing. Pull the cable
downward to make sure that the
rubber stopper protrudes to a
direction opposite to the network
cable head.
Paste the drill template and lead the
cables through the hole. Use a Ø 6mm-
6.5mm drill bit to drill 30 mm-depth
guide holes according to the template.
Knock the plastic rivets into the
guide holes and ensure that they
are tightened up.
1
2

10
3. Mount your camera.
1Connect all cables of
the ceiling and your
camera
2Lead self-tapping screws
through the guide holes in the
camera base, and fix your
camera on the ceiling by using
a screwdriver
4. Adjust the monitoring direction of the lens. Tighten the
screws after vertically adjusting the lens.

11
Lens base
1Rotate the lens base
horizontally.
Fastening screw
2Loosen the fastening
screws and rotate the
lens vertically.
Lens
3Rotate the lens horizontally.
The above steps are only applied to the camera with
manual zoom lens. For how to adjust the display of
the camera with motorized zoom lens, please see the
Web of the camera.
5. (Optional) Insert a SD card into the slot to use the local
storage function. For detailed specifications of
recommended SD cards, contact your dealer or
technical support. Hot plugging is not recommended.

12
6. Mount the transparent dome cover.
Align the screw holes in
the base and tighten the
three torx screws on the
edge of the transparent
dome cover to fix it

13
The preceding installation process is concealed
installation, during which holes are drilled in the
ceiling and tail cable is led out from the top of your
camera. Cables are connected and frapped at the
ceiling side to prevent messy cables from affecting
camera mounting. If open installation is adopted,
tail cable is led out from one side of your camera
and can be routed from the side groove of your
camera.
After mounting the dome cover, check that the
torx screws on the edge of the dome cover are
tightened up to ensure that your camera is
properly sealed. For details, see Mount the
transparent dome cover.
Access Your Camera
Before you begin, check that:
Your camera is operating properly and connected to the
network.
The PC you are using is installed with Internet Explorer
7.0 or later.
Follow these steps to access your camera through the Web
interface:
7. Open your browser, input the IP address of your camera
in the address bar and then press Enter to open the
login page.

14
8. Enter the username and password and then click Login.
Install the ActiveX at your first login. When the
installation of the ActiveX is completed, open your
IE to log in.
For your first login with Windows 7, if the system
does not prompt you to install ActiveX, follow
these steps to turn off UAC: click the Start button,
and then click Control Panel. In the search box,
type uac, and then click Change User Account
Control Settings. Move the slider to the Never
Notify position, and then click OK. After UAC is
turned off, log in again.
If the installation failed, open Internet Option in IE
before login. Click the Security tab, click Trusted
sites, and then click Sites to add the website. If
you use Windows 7, you need to save the
setup.exe to your PC first, and then right-click the
file, select Run as administrator, and then install it
according to instructions.