LTS Platinum Series User manual

Thermal & Opcal Bi-spectrum Network
Camera
User Manual

Symbol Convenons
The symbols that may be found in this document are dened as follows.
Symbol Descripon
Danger
Indicates a hazardous situaon which, if not avoided, will or could
result in death or serious injury.
Cauon
Indicates a potenally hazardous situaon which, if not avoided, could
result in equipment damage, data loss, performance degradaon, or
unexpected results.
Note Provides addional informaon to emphasize or supplement
important points of the main text.
Thermal & Opcal Bi-spectrum Network Camera User Manual
iii

Safety Instrucon
These instrucons are intended to ensure that user can use the product correctly to avoid danger
or property loss.
Laws and Regulaons
• In the use of the product, you must be in strict compliance with the electrical safety regulaons
of the naon and region.
Transportaon
• Keep the device in original or similar packaging while transporng it.
• Keep all wrappers aer unpacking them for future use. In case of any failure occurred, you need
to return the device to the factory with the original wrapper. Transportaon without the original
wrapper may result in damage on the device and the company shall not take any responsibilies.
• DO NOT drop the product or subject it to physical shock. Keep the device away from magnec
interference.
Power Supply
• Please purchase the charger by yourself. Input voltage should meet the Limited Power Source (5
VDC) according to the IEC62368 standard. Please refer to technical specicaons for detailed
informaon.
• Make sure the plug is properly connected to the power socket.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• DO NOT connect mulple devices to one power adapter, to avoid over-heang or re hazards
caused by overload.
• DO NOT touch the bare metal contacts of the inlets aer the circuit breaker is turned o.
Electricity sll exists.
• + idenes the posive terminal(s) of equipment which is used with, or generates direct current.
- idenes the negave terminal(s) of equipment which is used with, or generates direct current.
Baery
• Risk of explosion if the baery is replaced by an incorrect type. Dispose of used baeries
according to the instrucons. Il y a risque d'explosion si la baerie est remplacée par une
baerie de type incorrect. Mere au rebut les baeries usagées conformément aux instrucons.
• The built-in baery cannot be dismantled. Please contact the manufacture for repair if
necessary.
• For long-term storage of the baery, make sure it is fully charged every half year to ensure the
baery quality. Otherwise, damage may occur.
• This equipment is not suitable for use in locaons where children are likely to be present.
• Improper replacement of the baery with an incorrect type may defeat a safeguard (for
example, in the case of some lithium baery types).
Thermal & Opcal Bi-spectrum Network Camera User Manual
iv

• DO NOT dispose of the baery into re or a hot oven, or mechanically crush or cut the baery,
which may result in an explosion.
• DO NOT leave the baery in an extremely high temperature surrounding environment, which
may result in an explosion or the leakage of ammable liquid or gas.
• DO NOT subject the baery to extremely low air pressure, which may result in an explosion or
the leakage of ammable liquid or gas.
Installaon
• Never place the equipment in an unstable locaon. The equipment may fall, causing serious
personal injury or death.
• This equipment is for use only with corresponding brackets. Use with other (carts, stands, or
carriers) may result in instability causing injury.
System Security
• You acknowledge that the nature of Internet provides for inherent security risks, and our
company shall not take any responsibilies for abnormal operaon, privacy leakage or other
damages resulng from cyber aack, hacker aack, however, our company will provide mely
technical support if required.
• Please enforce the protecon for the personal informaon and the data security as the device
may be confronted with the network security problems when it is connected to the Internet.
Please contact us when the device might exist network security risks.
• Please understand that you have the responsibility to congure all the passwords and other
security sengs about the device, and keep your user name and password.
Maintenance
• If the product does not work properly, please contact your dealer or the nearest service center.
We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.
• A few device components (e.g., electrolyc capacitor) require regular replacement. The average
lifespan varies, so periodic checking is recommended. Contact your dealer for details.
• Wipe the device gently with a clean cloth and a small quanty of ethanol, if necessary.
• If the equipment is used in a manner not specied by the manufacturer, the protecon provided
by the device may be impaired.
• To reduce the risk of re, replace only with the same type and rang of fuse.
• The serial port of the equipment is used for debugging only.
Using Environment
• Make sure the running environment meets the requirement of the device. The operang
temperature shall be -30°C to 60°C (-22°F to 140°F), and the operang humidity shall be 95% or
less, no condensing.
• DO NOT expose the device to high electromagnec radiaon or dusty environments.
• DO NOT aim the lens at the sun or any other bright light.
Thermal & Opcal Bi-spectrum Network Camera User Manual
v

• The equipment shall not be exposed to dripping or splashing and that no objects lled with
liquids, such as vases, shall be placed on the equipment.
• No naked ame sources, such as lighted candles, should be placed on the equipment.
• Provide a surge suppressor at the inlet opening of the equipment under special condions such
as the mountain top, iron tower, and forest.
• Burned ngers when handling the parts with symbol . Wait one-half hour aer switching o
before handling the parts.
Emergency
• If smoke, odor, or noise arises from the device, immediately turn o the power, unplug the
power cable, and contact the service center.
COMPLIANCE NOTICE: The thermal series products might be subject to export controls in various
countries or regions, including without limitaon, the United States, European Union, United
Kingdom and/or other member countries of the Wassenaar Arrangement. Please consult your
professional legal or compliance expert or local government authories for any necessary export
license requirements if you intend to transfer, export, re-export the thermal series products
between dierent countries.
Thermal & Opcal Bi-spectrum Network Camera User Manual
vi

Contents
Chapter 1 Overview .................................................................................................................... 1
1.1 Brief Descripon .................................................................................................................... 1
1.2 Funcon ................................................................................................................................. 1
Chapter 2 Device Acvaon and Accessing ................................................................................. 2
2.1 Acvate the Device via SADP ................................................................................................. 2
2.2 Acvate the Device via Browser ............................................................................................. 2
2.3 Login ...................................................................................................................................... 3
2.3.1 Plug-in Installaon ........................................................................................................ 3
2.3.2 Illegal Login Lock ........................................................................................................... 4
Chapter 3 Temperature Measurement ........................................................................................ 5
3.1 Noce ..................................................................................................................................... 5
3.2 Thermography Conguraon Flow Chart ............................................................................... 5
3.3 Automac Thermography ...................................................................................................... 6
3.3.1 Set Thermography Parameters ..................................................................................... 7
3.3.2 Set Normal Mode .......................................................................................................... 8
3.3.3 Set Expert Mode ........................................................................................................... 9
3.3.4 Set Thermography Rule ................................................................................................. 9
3.3.5 Point Thermography ................................................................................................... 11
3.3.6 Line Thermography ..................................................................................................... 11
3.3.7 Area Thermography .................................................................................................... 11
3.3.8 Set Shielded Region .................................................................................................... 11
3.4 Manual Thermography ........................................................................................................ 12
Chapter 4 Fire Source Detecon ............................................................................................... 13
4.1 Recommended Scene .......................................................................................................... 13
4.2 Set Fire Detecon Parameters ............................................................................................. 13
Chapter 5 Behavior Analysis ..................................................................................................... 15
Thermal & Opcal Bi-spectrum Network Camera User Manual
vii

5.1 Flow Chart of Behavior Analysis ........................................................................................... 15
5.2 Set VCA Parameters ............................................................................................................. 15
5.3 Calibraon ............................................................................................................................ 16
5.3.1 Calibrate Automacally ............................................................................................... 16
5.3.2 Calibrate Manually ...................................................................................................... 17
5.3.3 Verify the Calibraon Result ....................................................................................... 18
5.4 Set Rules .............................................................................................................................. 18
5.5 Advanced Conguraon ....................................................................................................... 20
5.6 Set Global Size Filter ............................................................................................................ 21
Chapter 6 Event and Alarm ....................................................................................................... 22
6.1 Set Moon Detecon ........................................................................................................... 22
6.1.1 Normal Mode .............................................................................................................. 22
6.1.2 Expert Mode ............................................................................................................... 23
6.2 Set Video Tampering Alarm ................................................................................................. 24
6.3 Set Alarm Input .................................................................................................................... 25
6.4 Set Excepon Alarm ............................................................................................................. 26
6.5 Detect Audio Excepon ........................................................................................................ 26
Chapter 7 Arming Schedule and Alarm Linkage ......................................................................... 28
7.1 Set Arming Schedule ............................................................................................................ 28
7.2 Linkage Method Sengs ...................................................................................................... 28
7.2.1 Trigger Alarm Output .................................................................................................. 28
7.2.2 FTP/NAS/Memory Card Uploading ............................................................................. 29
7.2.3 Send Email .................................................................................................................. 30
7.2.4 Nofy Surveillance Center .......................................................................................... 31
7.2.5 Trigger Recording ........................................................................................................ 31
7.2.6 Set Audible Alarm Output ........................................................................................... 31
7.2.7 Set Flashing Alarm Light Output ................................................................................. 31
Chapter 8 Live View .................................................................................................................. 33
Thermal & Opcal Bi-spectrum Network Camera User Manual
viii

8.1 Live View Parameters ........................................................................................................... 33
8.1.1 Window Division ......................................................................................................... 33
8.1.2 Live View Stream Type ................................................................................................ 33
8.1.3 Enable and Disable Live View ...................................................................................... 33
8.1.4 Start Digital Zoom ....................................................................................................... 33
8.1.5 View Previous/Next Page ............................................................................................ 34
8.1.6 Full Screen ................................................................................................................... 34
8.1.7 Light ............................................................................................................................ 34
8.1.8 Wiper .......................................................................................................................... 34
8.1.9 Lens Inializaon ........................................................................................................ 34
8.1.10 Auxiliary Focus .......................................................................................................... 34
8.1.11 Quick Set Live View ................................................................................................... 34
8.1.12 Lens Parameters Adjustment .................................................................................... 35
8.2 Set Transmission Parameters ............................................................................................... 35
Chapter 9 Video and Audio ....................................................................................................... 37
9.1 Video Sengs ...................................................................................................................... 37
9.1.1 Stream Type ................................................................................................................ 37
9.1.2 Video Type .................................................................................................................. 37
9.1.3 Resoluon ................................................................................................................... 37
9.1.4 Bitrate Type and Max. Bitrate ..................................................................................... 38
9.1.5 Video Quality .............................................................................................................. 38
9.1.6 Frame Rate .................................................................................................................. 38
9.1.7 Video Encoding ........................................................................................................... 38
9.1.8 Smoothing ................................................................................................................... 40
9.1.9 Display VCA Info .......................................................................................................... 40
9.1.10 Audio Sengs ........................................................................................................... 40
9.1.11 Two-way Audio .......................................................................................................... 41
9.1.12 Set ROI ...................................................................................................................... 41
Thermal & Opcal Bi-spectrum Network Camera User Manual
ix

9.2 Display Sengs .................................................................................................................... 42
9.2.1 Image Adjustment ....................................................................................................... 42
9.2.2 Image Adjustment (Thermal Channel) ........................................................................ 42
9.2.3 Exposure Sengs ........................................................................................................ 43
9.2.4 Day/Night Switch ........................................................................................................ 43
9.2.5 Set Supplement Light .................................................................................................. 43
9.2.6 BLC .............................................................................................................................. 44
9.2.7 WDR ............................................................................................................................ 44
9.2.8 White Balance ............................................................................................................. 44
9.2.9 DNR ............................................................................................................................. 44
9.2.10 Defog ......................................................................................................................... 45
9.2.11 Gray Scale .................................................................................................................. 45
9.2.12 Set Palee ................................................................................................................. 45
9.2.13 Set Target Color ......................................................................................................... 45
9.2.14 DDE ........................................................................................................................... 46
9.2.15 Brightness Sudden Change ....................................................................................... 46
9.2.16 Enhance Regional Image ........................................................................................... 46
9.2.17 Mirror ........................................................................................................................ 46
9.2.18 Video Standard ......................................................................................................... 47
9.2.19 Digital Zoom .............................................................................................................. 47
9.2.20 Scene Mode .............................................................................................................. 47
9.3 OSD ...................................................................................................................................... 47
9.4 Set Privacy Mask .................................................................................................................. 48
9.5 Overlay Picture ..................................................................................................................... 48
9.6 Set Manual DPC (Defecve Pixel Correcon) ....................................................................... 48
9.7 Set Picture in Picture ............................................................................................................ 49
Chapter 10 Video Recording and Picture Capture ...................................................................... 50
10.1 Storage Sengs ................................................................................................................. 50
Thermal & Opcal Bi-spectrum Network Camera User Manual
x

10.1.1 Set Memory Card ...................................................................................................... 50
10.1.2 Set NAS ..................................................................................................................... 50
10.1.3 Set FTP ...................................................................................................................... 51
10.1.4 Set Cloud Storage ...................................................................................................... 51
10.2 Video Recording ................................................................................................................. 52
10.2.1 Record Automacally ................................................................................................ 52
10.2.2 Record Manually ....................................................................................................... 54
10.2.3 Playback and Download Video .................................................................................. 54
10.3 Capture Conguraon ........................................................................................................ 54
10.3.1 Capture Automacally .............................................................................................. 55
10.3.2 Capture Manually ..................................................................................................... 55
10.3.3 View and Download Picture ...................................................................................... 55
Chapter 11 Network Sengs .................................................................................................... 57
11.1 TCP/IP ................................................................................................................................. 57
11.1.1 Mulcast Discovery ................................................................................................... 58
11.2 Port .................................................................................................................................... 58
11.3 Port Mapping ..................................................................................................................... 59
11.3.1 Set Auto Port Mapping .............................................................................................. 59
11.3.2 Set Manual Port Mapping ......................................................................................... 60
11.4 Mulcast ............................................................................................................................ 60
11.5 SNMP ................................................................................................................................. 60
11.6 Access to Device via Domain Name ................................................................................... 61
11.7 Access to Device via PPPoE Dial Up Connecon ................................................................ 61
Thermal & Opcal Bi-spectrum Network Camera User Manual
xi

11.10 Set Open Network Video Interface .................................................................................. 64
11.11 Set Alarm Host ................................................................................................................. 65
11.12 Set Alarm Server .............................................................................................................. 65
Chapter 12 System and Security ................................................................................................ 66
12.1 View Device Informaon .................................................................................................... 66
12.2 Search and Manage Log ..................................................................................................... 66
12.3 Import and Export Conguraon File ................................................................................ 66
12.4 Export Diagnose Informaon ............................................................................................. 67
12.5 Reboot ............................................................................................................................... 67
12.6 Restore and Default ........................................................................................................... 67
12.7 Upgrade ............................................................................................................................. 67
12.8 View Open Source Soware License .................................................................................. 68
12.9 Time and Date .................................................................................................................... 68
12.9.1 Synchronize Time Manually ...................................................................................... 68
12.9.2 Set NTP Server .......................................................................................................... 68
12.9.3 Set DST ...................................................................................................................... 69
12.10 Set RS-232 ........................................................................................................................ 69
12.11 Set RS-485 ........................................................................................................................ 69
12.12 Set Same Unit .................................................................................................................. 70
12.13 Security ............................................................................................................................ 70
12.13.1 Authencaon ........................................................................................................ 70
12.13.2 Security Audit Log ................................................................................................... 70
12.13.3 Set IP Address Filter ................................................................................................ 71
12.13.4 Set SSH .................................................................................................................... 71
12.13.5 Set HTTPS ................................................................................................................ 72
12.13.6 Set QoS .................................................................................................................... 73
12.13.7 Set IEEE 802.1X ....................................................................................................... 73
12.14 User and Account ............................................................................................................. 73
Thermal & Opcal Bi-spectrum Network Camera User Manual
xii

12.14.1 Set User Account and Permission ........................................................................... 73
Chapter 13 Appendix ................................................................................................................ 75
13.1 Common Material Emissivity Reference ............................................................................ 75
13.2 Device Command ............................................................................................................... 75
13.3 Device Communicaon Matrix .......................................................................................... 76
13.4 FAQ ..................................................................................................................................... 76
Thermal & Opcal Bi-spectrum Network Camera User Manual
xiii

Chapter 1 Overview
1.1 Brief Descripon
Thermal & Opcal Bi-spectrum network camera equipped with built-in GPU which supports
intelligent behavior analysis algorithm, can realize high-precision VCA detecon and real-me
alarm. It is applied to perimeter defense and re-prevenon purposes in crical infrastructures
such as community, villa, construcon site, factory, 4S stores, and so on. The pre-alarm system
helps you discover unexpected events immediately and protects your property.
1.2 Funcon
This secon introduces main funcons of the device.
Note
Not all models support the conguraons below, take the actual product for reference.
Fire Detecon
Device can detect the dynamic re source in the scene and output pre-alarm and alarm to protect
the property.
Temperature Measurement
Device can measure the actual temperature of the spot being monitored. The device alarms when
temperature exceeds the temperature threshold value.
VCA
Device can do behavior analysis. Mulple rules can be congured for dierent requirements.
Smoking Detecon
Device can detect the smoking behavior and alarm.
Thermal & Opcal Bi-spectrum Network Camera User Manual
1

Chapter 2 Device Acvaon and Accessing
To protect the security and privacy of the user account and data, you should set a login password
to acvate the device when access the device via network.
Note
Refer to the user manual of the soware client for the detailed informaon about the client
soware acvaon.
2.1 Acvate the Device via SADP
Search and acvate the online devices via SADP soware.
Steps
1. Connect the device to network using the network cable.
2. Run SADP soware to search the online devices.
3. Check Device Status from the device list, and select Inacve device.
4. Create and input the new password in the password eld, and conrm the password.
Cauon
We highly recommend you create a strong password of your own choosing (using a minimum of
8 characters, including upper case leers, lower case leers, numbers, and special characters) in
order to increase the security of your product. And we recommend you reset your password
regularly, especially in the high security system, reseng the password monthly or weekly can
beer protect your product.
5. Click OK.
Device Status changes into Acve.
6. Oponal: Change the network parameters of the device in Modify Network Parameters.
2.2 Acvate the Device via Browser
You can access and acvate the device via the browser.
Steps
1. Connect the device to the PC using the network cables.
2. Change the IP address of the PC and device to the same segment.
Thermal & Opcal Bi-spectrum Network Camera User Manual
2

Note
The default IP address of the device is 192.168.1.64. You can set the IP address of the PC from
192.168.1.2 to 192.168.1.253 (except 192.168.1.64). For example, you can set the IP address of
the PC to 192.168.1.100.
3. Input 192.168.1.64 in the browser.
4. Set device acvaon password.
Cauon
We highly recommend you create a strong password of your own choosing (using a minimum of
8 characters, including at least three of the following categories: upper case leers, lower case
leers, numbers, and special characters) in order to increase the security of your product. And
we recommend you reset your password regularly, especially in the high security system,
reseng the password monthly or weekly can beer protect your product.
5. Click OK.
6. Input the acvaon password to log in to the device.
7. Oponal: Go to Conguraon → Network → Basic → TCP/IP to change the IP address of the
device to the same segment of your network.
2.3 Login
Log in to the device via Web browser.
2.3.1 Plug-in Installaon
Certain operaon systems and web browser may restrict the display and operaon of the device
funcon. You should install plug-in or complete certain sengs to ensure normal display and
operaon. For detailed restricted funcon, refer to the actual device.
Operang System Web Browser Operaon
Windows Internet Explorer 10+ Follow pop-up prompts to
complete plug-in installaon.
Google Chrome 57+
Mozilla Firefox 52+
Click to
download and install plug-in.
Go to Conguraon →
Network → Advanced Sengs
→ Network Service to enable
WebSocket or WebSockets for
normal view if plug-in
installaon is not required.
Thermal & Opcal Bi-spectrum Network Camera User Manual
3

Operang System Web Browser Operaon
Display and operaon of
certain funcons are restricted.
For example, Playback and
Picture are not available. For
detailed restricted funcon,
refer to the actual device.
Mac OS 10.13+ Mac Safari 12+ Plug-in installaon is not
required.
Go to Conguraon →
Network → Advanced Sengs
→ Network Service to enable
WebSocket or WebSockets for
normal view. Display and
operaon of certain funcons
are restricted. For example,
Playback and Picture are not
available. For detailed
restricted funcon, refer to the
actual device.
Note
The device only supports Windows and Mac OS system and does not support Linux system.
2.3.2 Illegal Login Lock
It helps to improve the security when accessing the device via Internet.
Go to Conguraon → System → Security → Security Service , and enable Enable Illegal Login
Lock. Illegal Login Aempts and Locking Duraon are congurable.
Illegal Login Aempts
When your login aempts with the wrong password reach the set mes, the device is locked.
Locking Duraon
The device releases the lock aer the seng duraon.
Thermal & Opcal Bi-spectrum Network Camera User Manual
4

Chapter 3 Temperature Measurement
When you enable this funcon, the device measures the actual temperature of the scene. It alarms
when temperature exceeds the temperature threshold value.
3.1 Noce
This part introduces the noces of conguring temperature measurement funcon.
• The target surface should be as vercal to the opcal axis as possible. It is recommended that
the angle of oblique image plane should be less than 45°.
• The target image pixels should be more than 5 × 5.
• If mulple presets will be taken for temperature measurement, it is recommended to set the
patrol me above 20 s.
• Please select line thermography or area thermography for a certain area temperature
measurement. The point thermography is not recommended in case of deviaon occurred
during device movement to aect the accuracy of temperature measurement.
3.2 Thermography Conguraon Flow Chart
This part introduces the process of conguring temperature measurement.
Thermal & Opcal Bi-spectrum Network Camera User Manual
5

Figure 3-1 Thermography Conguraon Flow Chart
Note
Please refer to the Quick Start Guide for detailed informaon of Installaon part in the ow chart.
3.3 Automac Thermography
Congure the temperature measurement parameters and temperature measurement rules. The
device can measure the actual temperature and output alarms when temperature exceeds the
alarm threshold value.
Thermal & Opcal Bi-spectrum Network Camera User Manual
6

3.3.1 Set Thermography Parameters
Congure the parameters of temperature measurement.
Steps
1. Go to Conguraon → Local , enable Display Temperature Info. .
Display Temperature Info.
Select Yes to display temperature informaon on live view.
Enable Rules to display the rules informaon on live view.
2. Click Save.
3. Go to Conguraon → Temperature Measurement → Basic Sengs to congure parameters.
Enable Temperature Measurement
Check to enable temperature measurement funcon.
Enable Color-Temperature
Check to display Temperature-Color Ruler in live view.
Display Temperature Info. on Stream
Check to display temperature informaon on the stream.
Display Temperature in Opcal Channel
Check to display thermal channel temperature informaon in the opcal channel.
Display Max./Min./Average Temperature
Check to display maximum/minimum/average temperature informaon on liveview when
the temperature measurement rule is line or area.
Posion of Thermometry Info
Select the posion of temperature informaon showed on the live view.
• Near Target: display the informaon beside the temperature measurement rule.
• Top Le: display the informaon on the top le of screen.
Add Original Data on Capture
Check to add data on alarm triggered capture of thermal channel.
Add Original Data on Stream
Check to add original data on thermal view.
Data Refresh Interval
It means the refresh interval of temperature informaon.
Unit
Display temperature with Degree Celsius (°C)/Degree Fahrenheit (°F)/Degree Kelvin (K).
Temperature Range
Select the temperature measurement range.
Thermal & Opcal Bi-spectrum Network Camera User Manual
7

Version
View the version of current algorithm.
Calibraon File Version
View the version of calibraon le.
Alarm Interval
Set the alarm interval between two alarms.
Reect Light Filter & Forkli Filter
Enable these funcons if there is strong reect light from sun or forkli in the scene. Or it
may cause false alarm. Click Restart to restart algorithm library.
Note
The sengs vary according to dierent camera models.
4. Click Save.
3.3.2 Set Normal Mode
This funcon is used to measure the temperature of the whole scene and alarm.
Steps
1. Go to Conguraon → Temperature Measurement → Basic Sengs , and check Enable
Temperature Measurement.
2. Refer to Set Thermography Parameters to set the parameters.
3. Go to Conguraon → Temperature Measurement → Advanced Sengs , and select Normal.
4. Congure the parameters of normal mode.
Emissivity
Set the emissivity of your target. The emissivity of each object is dierent.
Distance
The distance between the target and the device.
Pre-Alarm Threshold
When the temperature of target exceeds the pre-alarm threshold, and this status keeps more
than Filtering Time, it triggers pre-alarm.
Alarm Threshold
When the temperature of target exceeds the alarm threshold, and this status keeps more
than Filtering Time, it triggers alarm.
Pre-Alarm Output and Alarm Output
Check Pre-Alarm Output and Alarm Output to link the pre-alarm or alarm with the
connected alarm device.
Thermal & Opcal Bi-spectrum Network Camera User Manual
8