Lucent Technologies LINEAGE 2000 FPS User manual

Product Manual
167-790-048
Comcode 107044471
Issue 4
August 1996
Lucent Technologies
LINEAGE®2000
Flexible Power System
Monitor and Control Unit
Notice:
Every effort was made to ensure that the information in this
document was complete and accurate at the time of printing.
However, information is subject to change.
©1996 Lucent Technologies
All Rights Reserved
Printed in U.S.A.

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Table of Contents 1
Table of Contents
1 Introduction
General Information 1 - 1
Technical Support 1 - 3
USA, Canada, Puerto Rico, and the US Virgin Islands 1 - 3
Central and South America 1 - 3
Europe, Middle East, and Africa 1 - 3
Asia Pacific Region 1 - 3
Product Repair and Return 1 - 4
USA, Canada, Puerto Rico, and the US Virgin Islands 1 - 4
Central and South America 1 - 4
Europe, Middle East, and Africa 1 - 4
Asia Pacific Region 1 - 4
Customer Service 1 - 4
2 Product Description
Monitor and Control Unit Specifications 2 - 1
Feature Description 2 - 2
Operating Voltage 2 - 2
Office Alarm Contacts 2 - 2
Adjustable Battery on Discharge Alarm 2 - 4
Rectifier/Converter Failure Alarm 2 - 5
AC Fail 2 - 6
Major Fuse Alarm 2 - 6
Front Panel Status Indicators 2 - 6
Front Panel Meter 2 - 7
LED Test Button 2 - 7
Voltage Adjust 2 - 7
Front Panel Test Jacks 2 - 8
On/Standby 2 - 8
3 Installation and Setup
Hardware Setup 3 - 2
Battery on Discharge Threshold 3 - 2
Unit Installation 3 - 2
Office Alarms - Field Wiring 3 - 2

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
2 Table of Contents Issue 4 August 1996
4 Acceptance Testing
LED Test 4 - 1
Meter Accuracy 4 - 2
Battery on Discharge (115C only) 4 - 2
Fuse Alarm Test 4 - 3
On/Standby Test 4 - 4
For 115B: 4 - 4
For 115C: 4 - 4
Voltage Adjust 4 - 5
For 115B: 4 - 5
For 115C: 4 - 5
5 Operation
6 Product Warranty

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 List of Figures 1
List of Figures
Figure 1-1: Monitor and Control Unit For Flexible Power
System 1 - 5
Figure 1-2: Monitor and Control Unit For Flexible Power
System (Block Diagram) 1 - 6
Figure 5-1: Front Panel Controls and Displays 5 - 2

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 List of Tables 1
List of Tables
Table 1-A: Feature Summary 1 - 2
Table 2-A: 115B and 115C Monitor and Control Unit
Specifications 2 - 1
Table 2-B: BD Voltage 2 - 5
Table 2-C: Alarm and Control Signals 2 - 9

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Introduction 1 - 1
1 Introduction
General
Information This product manual (167-790-048) describes the 115B and
115C Monitor and Control Units used in the Lucent
Technologies Lineage® 2000 Flexible Power System (FPS).
The FPS consists of the Lucent Technologies Lineage® 2000
Small Converter Plant (SCP) and the Lineage® 2000 Small
Rectifier-Converter Plant (SRCP). The topics covered in this
manual include general description, basic features, options,
installation and configuration, acceptance testing and operation
for the Monitor and Control Unit.
The pluggable 115B or 115C Monitor and Control Unit
performs the centralized monitoring and reporting functions for
the components of theFPS system such as the 693AA converters
and 592A switch-mode rectifiers, FPS distribution systems, as
well as future products used in the FPS. The 115B is used with
the Small Converter Plant and the 115C is used with the Small
Rectifier-Converter Plant. A terminal board is provided with the
shelf to allow the customer to access the office alarms
connections and for remote On/Standby control of the rectifiers
and converters. The Monitor and Control incorporates features
needed for both the converter-only SCP and the rectifier-
converter SRCP plants. A complete feature set is provided for
converters in SCPs and rectifiers in SRCPs. A limitedfeature set
for monitoring alarms is provided for converters in an SRCP.
Table 1-A is a summary of these features:

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
1 - 2 Introduction Issue 4 August 1996
Table 1-A: Feature Summary
Small Converter Plant (SCP) (115B)
Converter Features
Converter Voltage Monitoring
Converter Current Monitoring
Converter Voltage Adjust
Converter Voltage Measurable by ECS CP3
Converter Current Measurable by ECS CP3
Converter Voltage to Front Panel Test Jacks
Full Converter Alarm Monitoring
LED Test for LCD & LEDs
Converter On/Standby Control
PMN & PMJ Alarms sent to ECS CP1
Small Rectifier-Converter Plant (SRCP) (115C)
Converter Features Rectifier Features
N/A Rectifier Voltage Monitoring
N/A Rectifier Current Monitoring
N/A Rectifier Voltage Adjust
N/A Rectifier Voltage Measurable by CP3
N/A Rectifier Current Measurable by CP3
N/A Rectifier Voltage to Front Panel Test Jacks
Converter On/Standby Control Rectifier On/Standby Control
Full Converter Alarm Monitoring Full Rectifier Alarm Monitoring
LED Test for LCD & LEDs Yes
PMN & PMJ Alarms sent to ECS CP1 Yes

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Introduction 1 - 3
The 115C Monitor and Control Unit is shown in Figure 1-1.
Figure 1-2 is a block diagram of the 115 Monitor and Control
Unit. It shows the various alarm gathering and reporting
functions, voltage and current monitoring, interface for a future
remote access option, and the front panel LCD display and
LEDs.
Technical
Support Technical support for Lucent Technologies Technologies
equipment is available to customers around the world.
USA, Canada,
Puerto Rico, and
the US Virgin
Islands
Onapost-salebasis,duringtheProductWarrantyperiod,our
Technical Supporttelephone number 1-800-CAL RTAC (1-800-
225-7822) provides coverage during normal business hours.
Product Specialists are available to answer your technical
questions and assist in troubleshooting problems. For out-of-
hours EMERGENCIES, the 800 number will put you in touch
with a Regional Technical Assistance Center Engineer via our
24 hour a day, 7 day per week Help Desk.
When Technical Support is required in the Post-Warranty
Period, the service may be billable unless you hold an extended
warranty or contractual agreement.
Central and
South America If you need product technical support, contact your local Field Support/Regional Technical Assistance Center or contact your
sales representative who will be happy to discuss your specific
needs.
Europe, Middle
East, and Africa If you need product technical support, contact your local Field Support/Regional Technical Assistance Center or contact your
sales representative who will be happy to discuss your specific
needs.
Asia Pacific
Region If you need product technical support, contact your local Field Support/Regional Technical Assistance Center or contact your
sales representative who will be happy to discuss your specific
needs.

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
1 - 4 Introduction Issue 4 August 1996
Product Repair
and Return Repair and return service for Lucent Technologies Technologies
equipment is available to customers around the world.
USA, Canada,
Puerto Rico, and
the US Virgin
Islands
For information on returning of products for repair, customers
may call 1-800-255-1402 for assistance.
Central and
South America If you need to return a product for repair, your sales representative will be happy to discuss your individual situation.
Europe, Middle
East, and Africa If you need to return a product for repair, your sales representative will be happy to discuss your individual situation.
Asia Pacific
Region If you need to return a product for repair, your sales representative will be happy to discuss your individual situation.
Customer
Service For customer service, any other product or service information,
or for additional copies of this manual or other Lucent
Technologies Technologies documents, call 1-800-THE-1PWR
(1-800-843-1797). Specify the select code number for manuals,
or drawing number for drawings. Contact your regional
customer service organization or sales representative for
information regarding spare parts.

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Introduction 1 - 5
Figure 1-1: Monitor and Control Unit For Flexible Power
System
AC Fall
PHIII
Normal MJFG
PIU
IO
Voltage
Current
LED Test VADJ
Lucent
SW 440
CM1
F1 F2
R3
R12
R16
R41 R73
J2
AF

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
1 - 6 Introduction Issue 4 August 1996
Figure 1-2: Monitor and Control Unit For Flexible Power
System (Block Diagram)
ECD
CP1 FORM C CONTACTS
ALARMS FRONT PANEL
LEDS
CONVERTER
RECTIFIER
DISTRIBUTION
REMOTE ACCESS
BATTERY
TERMINATION PANEL
BATTERY
TERMINATION
PANEL
CONVERTERS
OR RECTIFIERS
OUTPUT VOLTAGE
ADJUST
VI
VOLTAGE/CURRENT
MONITORING
CONV RECT
LAMP TEST AND
ON/STANDBY
METER
REMOTE ACCESS
INTERFACE 3 1/2 DIGIT LCD
FPS REMOTE
ACCESS
CP3

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Product Description 2 - 1
2 Product Description
Monitor and
Control Unit
Specifications
Table 2-A: 115B and 115C Monitor and Control Unit Specifications
115B 115C
Operating Voltage: 19 VDC to 30 VDC 38 VDC to 72 VDC
Input Power: 3.5 watts max 4.0 watts max
Operational Temperature: 0°C to +50°C
Display Meter: 3-1/2 digit backlit LCD
Range: 0.0 to 150.0V (voltmeter)
Range: 0 to 150A (ammeter)
Voltage Accuracy: +/-1% of reading
Current Accuracy: +/-1% of reading +/-1A
Resolution: +/-0.1 volt
Resolution: +/-0.1 ampere
Plant Voltage Setting: Adjustable by potentiometer on Monitor and Control Unit
front panel
693AA Converter 48V to 52V
592A Rectifier 48V to 56V

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
2 - 2 Product Description Issue 4 August 1996
Feature
Description
Operating
Voltage The115 MonitorandControlUnit isoperatedfromaDC voltage as specified abovein theControllerSpecifications.Either the (+)
or (-) input may be tied to ground or left floating.
Office Alarm
Contacts A set of Form C contacts is brought out to the BFD1 terminal board, located on the side of the shelf, for each of the following
plant alarms:
ECS Controller Datalogger
Outputs: Range: 0 to 6V (for monitoring plant voltage)
Range: 0 to 6V (for monitoring
plant current)
Voltage Accuracy: +/-1.5% of reading
Current Accuracy: +/-2% of reading +/-1A
Alarm Contact Ratings: 60VDC, 0.5A, Form C
BD Settings: Adjustable from 46V to 55V in steps of 1.0V +/- 0.5V
(115C only); the default BD setting is 51V
Altitude: -200 to 13,000 feet
Humidity: 20% to 80% non-condensing
Electrostatic Discharge: IEC 801-2 Level 3
Radiated & Conducted
Emissions: FCC Level A
Electromagnetic Immunity: 10V/m over the range of 60 Hz to 30 kHz
LED Test: Lights all segments of LCD, all LEDs on Monitor and
Control and Power Units
Table 2-A: 115B and 115C Monitor and Control Unit Specifications

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Product Description 2 - 3
See Table 2-C for connections to BFD1 terminal board.
These are Form-C, or transfer type,contacts to allow an installer
to connect the Monitor and Control Unit to the office alarms
system. Each set of contacts consists of a combination of
normally open and normally closed contacts with one side of
each in common. The normally open contact is referred to as
NO, the normally closed contact is referred to as NC, and the
common or return contact is referred to as C. Each Form C set is
isolated. The alarm state is the “normal” state, i.e., when an
alarm condition exists, a closure exists between the NC and C
poles and an open exists between the NO and C poles. If the
Monitor and Control Unit is powered down, all alarm relays are
de-energized and all alarms are available to the office alarm
system.
Code Alarm Condition for Alarm
115B Power Major (PMJ) Two or more converters alarm or go on/standby.
(Also creates a PMN alarm.)
Power Minor (PMN) One converter alarms or goes on/standby.
Major Fuse Alarm (MJF) Activated by distribution fuse or breaker alarm.
(Also creates a PMJ alarm.)
115C Power Major (PMJ) Battery thermal alarm, temperature compensation
activated at 55°C (optional).
Two or more rectifier and/or two or more
converter alarms. (Also creates a PMN alarm.)
Power Minor (PMN) Battery thermal alarm, temperature compensation
activated at 42°C (optional).
One rectifier and/or one converter alarm.
Major Fuse Alarm (MJF) Activated by distribution fuse or breaker alarm.
(Also creates a PMJ alarm.)
Battery-on-Discharge (BD) Activated when Plant Voltage drops below
programmed BD threshold. (Also creates a PMJ
alarm.)
AC Failure (ACF) Activated by rectifier when input AC power falls
below the normal operating range. (Also creates a
PMN alarm.)

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
2 - 4 Product Description Issue 4 August 1996
Adjustable
Battery on
Discharge Alarm
The Battery on Discharge (BD) alarm is provided for a SRCP
plantequippedwithbackupbatteries.In theevent thatAC power
is lost, the batteries provide power for a period of time to allow
maintenance personnel to correct the problem. While the
batteries are providing the plant's power, the plant voltage will
be decreasing until a point at which the connected load will not
operate will be reached. The 115C, which is used in the SRCP,
contains a DIP-switch settable BD alarm to monitor the plant
voltage. Whenever the plant voltage drops below this preset
threshold, the Monitor and Control Unit issues a Battery on
Discharge alarm, a PMJ alarm, and lights both the red BD and
PMJ LEDs on its front panel.
It should be noted that a BD alarm does not necessarily indicate
thatrectifier outputcurrenthas been lostor reduced.A BDalarm
can be caused by adjusting the plant voltage via the
potentiometer on the Monitor and Control Unit front panel to a
level below the BD setpoint. It can also be caused by a current
overload on normally functioning rectifiers. The voltage
threshold for the BD alarm is selected by the user by setting
SW440 on the main circuit board of the Monitor and Control.
The setpoint is typically at least 3 volts below the plant float
voltage for nominal 48V plants. This threshold avoids nuisance
alarms due to component tolerances, variations in load, and
othertransient conditions.SeeTable2-Bforthe switchpositions
for BD.

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Product Description 2 - 5
Rectifier/
Converter
Failure Alarm
Whenever a single rectifier failure (RFA) and/or a single
converter failure (CFA) alarm is received by the Monitor and
ControlUnit, a Power Minor (PMN) alarm is issued to the office
alarm system via a Form-C relay contact, and a yellow LED is
lit on the front of the Monitor and Control Unit. If two or more
rectifier failures and/or two or more converter failures are
received by the Monitor and Control Unit, both the PMN and the
Power Major (PMJ) alarm will be issued, and both the yellow
PMN and the red PMJ LED are lit. Since a loss of a single
rectifier and/or converter may not necessarily affect the plant
voltage and constitute an emergency, it is treated as a minor
alarm. It should be noted, however, that a CFA is sent by each
converter in the standby mode. Therefore, a PMJ will be issued
whenever two or more converters are turned off, even if they are
not needed.
Table 2-B: BD Voltage
O = Switch Open, C = Switch Closed
Voltage SW 440A
(.5V)
SW
440B
(1V)
SW
440C
(2V)
SW
440D
(4V)
SW
440E
(8V)
SW
440F
(24/48) Notes
23.0 +.25V
23.5 +.25V
24.0 +.25V
24.5 +.25V
25.0 +.25V
25.5 +.25V
26.0 +.25V
26.5 +.25V
27.0 +.25V
27.5 +.25V
28.0 +.25V
C
O
C
O
C
O
C
O
C
O
C
C
C
O
O
C
C
O
O
C
C
O
C
C
C
C
O
O
O
O
C
C
C
C
C
C
C
C
C
C
C
O
O
O
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
115A Not
Available
46.0 +/-.5V
47.0 +/-.5V
48.0 +/-.5V
49.0 +/-.5V
50.0 +/-.5V
51.0 +/-.5V
52.0 +/-.5V
53.0 +/-.5V
54.0 +/-.5V
55.0 +/-.5V
C
C
C
C
C
C
C
C
C
C
C
O
C
O
C
O
C
O
C
O
C
C
O
O
C
C
O
O
C
C
C
C
C
C
O
O
O
O
C
C
C
C
C
C
C
C
C
C
O
O
O
O
O
O
O
O
O
O
O
O
115C Factory
Pre-set 51V

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
2 - 6 Product Description Issue 4 August 1996
AC Fail The AC Fail Alarm, which is only provided on the 115C, is
intended to indicate that ac input power to at least one rectifier
has disappeared or dropped below a minimum voltage. This
alarm is provided as an isolated transfer contact for the office
alarm systems. An ACF alarm also issues a PMN alarm so that
both the yellow PMN and ACF LEDs will be lit.
Major Fuse
Alarm The Monitor and Control Unit monitors the distribution for blown fuses and/or tripped breakers. Since a blown fuse or
tripped breaker in the distribution indicates that some partof the
customer's equipment has lost power, a Power Major (PMJ)
alarm will be issued in addition to the Major Fuse alarm (MJF).
The MJF is sent to the office alarms via a single Form-C transfer
contact and both the red PMJ and MJF LEDs will be lit on the
front of the Monitor and Control Unit.
Front Panel
Status Indicators Light-emitting diodes are located on the frontpanel of the 115 to indicate the alarm status of the plant. The LEDs are as follows:
Name Color MJ/MN Function
115B
Normal Green N/A Indicates system normal operation
PMJ Red Major Major alarm, can be service affecting
PMN Yellow Minor Minor alarm, not service affecting
MJF Red Major Blown fuse or tripped breaker in distribution
115C
Normal Green N/A Indicates system normal operation
PMJ Red Major Major alarm, can be service affecting
PMN Yellow Minor Minor alarm, not service affecting
MJF Red Major Blown fuse or tripped breaker in distribution
BD Red Major Battery on Discharge, plant voltage is low
ACF Yellow Minor AC power is missing or low to rectifier(s)

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Product Description 2 - 7
Front Panel
Meter A3-1/2digit,backlit liquid-crystal display is located on the front of the Monitor and Control Unit. A switch near the display
selects either the plant voltage or the plant current to be shown.
When the meter select switch is set in the AMPS position, the
display indicates the following current in amperes:
The 115C monitors both the total current sourced from the
rectifiers as well as the current that flows through the batteries.
The battery current is measured with an external shunt placed in
the battery string. The 115C sums the total rectifier current with
the battery current (current flowing out of the battery during
discharge is positive, current flowing into the batteries during
charge and float is negative) to derive the true plant current. In
the case of an AC failure in which all the rectifiers are not
powered and the batteries are providing the source current, the
LCDwilldisplay the total batterycurrent,which isnowthe same
as the total load current. When AC is restored, the battery
recharge current is subtracted from the total rectifier output
current to derive the plant load current. When the meter select
switch is set in the VOLTAGE position, the display indicates the
following voltage:
LED Test Button Depressing the LED Test button will cause all of the LCD
segments to display 188.8 and all LEDs in the FPSto light while
the switch is pressed.
Voltage Adjust A potentiometer is provided on the Monitor and Control Unit to
allow the customer to adjust the plant output voltage. The 115B
adjust the converters' output voltage while the 115C adjusts the
rectifiers' output voltage. In the event that the Monitor and
Control unit were to lose power, the voltage adjust signal from
the Monitor and Control Unit would be disconnected from the
voltage adjust bus, setting rectifiers/converters to their nominal
voltage.
115B 115C
Total Conv Output Current Rectifier Output + Battery
Current
115B 115C
Converter Output Voltage Rectifier Output Voltage

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
2 - 8 Product Description Issue 4 August 1996
Front Panel Test
Jacks Test points are provided on the front panel so that the plant voltagemaybecheckedwiththe user' smeter.Thetestpointsare
current-limitedagainst accidental shortcircuits by test probes.In
the 115B, the converter output voltage is brought out to the test
points. In the 115C, the rectifier outputvoltage is brought out to
the test points.
On/Standby Terminal block connections are provided in the alarm wiring
area as inputs to the 115 Monitor and Control Unit to allow the
customer to put the rectifiers and/or converters in the On/
Standby mode. The converter shelf provides a connection for
putting all converters on standby. The rectifier converter shelf
provides connections for putting all converters and/or rectifiers
on standby. See Table 2-C for pin assignments.
CP1 Connections
The Monitor and Control Unit provides two sets of relay
contacts for use with a Lineage®2000 ECS Controller (CP1) for
alarm reporting. Either a PMN or a PMJ alarm in the FPS will
provide a contact closure, through a series 4.64 kohm resistor to
the CP1 Batt, RPMN, and RPMJ inputs, respectively. See Table
2-C for pin assignments.
CP3 Connections
The Monitor and Control Unit provides a dc voltage signal that
is proportional to the plant voltage and a dc voltage signal that is
proportional to the plant current that may be read by the CP3
datalogger board in a Lineage®2000 ECS controller. Each
signal is 0 to 6 VDC and must be scaled by the ECS controller
by multiplying the voltage read by 25 to derive the actual plant
voltage or current. These signals can be accessed at connector
J202 on the right side of the shelf.
Terminal Board
The BFD1 terminal board, located on the left side of the shelf, is
provided for the customer to access the office alarm relay
contacts and the controls to put the rectifiers and/or converters
On/Standby. Table 2-C shows those connections:

Lucent Technologies Lineage®2000 FPS Monitor and Control Unit
Issue 4 August 1996 Product Description 2 - 9
Table 2-C: Alarm and Control Signals
TB3 TB4
1 BATT 1 BD - NO
2 AUX - PMJ 2 BD-C
3 AUX - PMN 3 BD-NC
4 4 PMJ - NO
5 CONV O/S 5 PMJ - C
6 O/S RTN 6 PMJ - NC
7 RECT O/S 7 PMN - NO
8 O/S RTN 8 PMN - C
99PMN-NC
10 ACF - NO 10 MJF - NO
11 ACF - C 11 MJF - C
12 ACF - NC 12 MJF - NC