Ludlum Measurements 3002 User manual

Model 3002 Digital Survey Meter
Ludlum Measurements
December 2021
Serial Number: 25017740 and Succeeding
Firmware: n20.1790 and Higher

Model 3002 Digital Survey Meter
Ludlum Measurements
December 2021
Serial Number: 25017740 and Succeeding
Firmware: n20.1790 and Higher

STATEMENT OF WARRANTY
Ludlum Measurements, Inc. warrants the products covered in this manual to be free of de-
fects due to workmanship, material, and design for a period of twelve months from the date
of delivery. The calibration of a product is warranted to be within its specified accuracy lim-
its at the time of shipment. In the event of instrument failure, notify Ludlum Measurements
to determine if repair, recalibration, or replacement is required.
This warranty excludes the replacement of photomultiplier tubes, G-M and proportional
tubes, and scintillation crystals which are broken due to excessive physical abuse or used
for purposes other than intended.
There are no warranties, express or implied, including without limitation any implied war-
ranty of merchantability or fitness, which extend beyond the description of the face there
of. If the product does not perform as warranted herein, purchaser’s sole remedy shall be
repair or replacement, at the option of Ludlum Measurements. In no event will Ludlum
Measurements be liable for damages, lost revenue, lost wages, or any other incidental or
consequential damages, arising from the purchase, use, or inability to use product.
RETURN OF GOODS TO MANUFACTURER
If equipment needs to be returned to Ludlum Measurements, Inc. for repair or calibration,
please send to the address below. All shipments should include documentation contain-
ing return shipping address, customer name, telephone number, description of service re-
quested, and all other necessary information. Your cooperation will expedite the return of
your equipment.
LUDLUM MEASUREMENTS, INC.
ATTN: REPAIR DEPARTMENT
501 OAK STREET
SWEETWATER, TX 79556
800-622-0828 325-235-5494
FAX [phone]

CONTENTS
Contents 3
List of Figures 5
List of Tables 7
1 Introduction 9
2 Getting Started 11
2.1 Unpacking and Repacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 Instrument Operational Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3.1 Turning the Instrument On . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4 Detector Failure Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.1 Detector Loss of Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.2 Detector Over Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.3 Detector Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5 Instrument Use And Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5.1 ON/OFF Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5.2 Alpha-Beta Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.5.3 AUDIO Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.5.4 MODE Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.5.5 LOG Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.6 RATE Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.7 MAX Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.8 COUNT Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3 Specifications 25
4 Setup Mode 27
4.1 Setup Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2 Setup Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.3 Entering Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.4 Setup Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.5 Model 3002 List of Parameters (in order) . . . . . . . . . . . . . . . . . . . . . . . 31
4.6 Setup Page 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.7 Setup Page 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.8 Setup Page 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.9 Setup Page 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.10 Setup Page 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5 Datalogging 43
5.1 Datalogging Operation – Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3

4CONTENTS
5.2 Datalogging Operation – Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.3 Data Log Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.4 Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6 Software 47
6.1 Connecting to Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7 Advanced Features 49
7.1 Software Calibration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.2 Instrument Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.3 Other Device Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.4 Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7.5 Real-time Streaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7.6 Button Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7.7 CPS Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8 Safety Considerations 53
8.1 Environmental Conditions for Normal Use . . . . . . . . . . . . . . . . . . . . . 53
8.2 Warning Markings and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8.3 Cleaning and Maintenance Precautions . . . . . . . . . . . . . . . . . . . . . . . 54
9 Revision History 55
10 Recycling 57
11 Options 59
12 Standard Parts List 61
A Auxiliary Communications 63
A.1 AuxCom Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.2 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.3 Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.3.1 AuxCom Usage - Hot Key . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.3.2 AuxCom Usage - Pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
A.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.4.1 AuxCom Setting - Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.4.2 AuxCom Setting - Off Time . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.4.3 AuxCom Setting - Pwr Mode . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.4.4 AuxCom Setting - Write Protect . . . . . . . . . . . . . . . . . . . . . . . . 67
A.4.5 AuxCom Setting - Encryption . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.4.6 AuxCom Setting - Auto Mode Interval . . . . . . . . . . . . . . . . . . . . 68
Ludlum Measurements, Inc.

LIST OF FIGURES
2.1 Startup Display (All Segments Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2 Firmware Version Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Battery Voltage Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Startup Display Showing 189 Stored Data Records . . . . . . . . . . . . . . . . . . . 13
2.5 Detector Loss of Count Display-Alpha (Display Will Flash) . . . . . . . . . . . . . . 14
2.6 Detector Over Range-Alpha (Display Will Flash) . . . . . . . . . . . . . . . . . . . . 15
2.7 Detector Overload Alarm (Display Will Flash) . . . . . . . . . . . . . . . . . . . . . . 15
2.8 RATE Mode Displaying Background Radiation Rate . . . . . . . . . . . . . . . . . . 20
2.9 MAX Mode Display With ALARM Indication . . . . . . . . . . . . . . . . . . . . . . . 20
2.10 COUNT Mode Displaying COUNT Timer of 5 Minutes, 30 Seconds . . . . . . . . . 23
4.1 Setup Page Selection Display (showing page 4-CAL) . . . . . . . . . . . . . . . . . . 30
5.1 Displaying Datalog Table Index of 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.2 Displaying Datalog Location ID Table Index of 36 . . . . . . . . . . . . . . . . . . . . 44
A.1 Example – Device Selection In Lumic Linker App (iOS) . . . . . . . . . . . . . . . . 65
A.2 Example – Pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
A.3 Example – Model 3000 series Found in Lumic Linker App (iOS) . . . . . . . . . . . . 65
A.4 Example – Entering PIN In Lumic Linker App (iOS) . . . . . . . . . . . . . . . . . . . 65
A.5 Example – Lumic 2.0 Calibration Software . . . . . . . . . . . . . . . . . . . . . . . . 66
5

LIST OF TABLES
2.1 COUNT Mode Units and Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.1 Setup Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 Response Time Based on Count Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.3 Units and Multipliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4 Count Units and Multipliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
12.1 Standard Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
A.1 AuxCom Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.2 AuxCom Auto Off Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.3 AuxCom Power on at Boot-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.4 AuxCom Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.5 AuxCom Encription . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
A.6 AuxCom Auto Mode Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7

CHAPTER
1
INTRODUCTION
The Model 3002 is an ergonomic, lightweight instrument which is designed to be used for
simultaneous alpha and beta radiation survey. The Model 3002 features the ability to mea-
sure radiation in count rate, exposure rate/dose, activity rate, time-averaged rates, and scaler
counts. The Model 3002 utilizes an external radiation detector to detect alpha and beta radi-
ation, typically either a scintillation or gas-proportional detector.
Three modes of operation are available for the Model 3002 – RATE, MAX, and COUNT.
It is possible to make the instrument operation even simpler by restricting the number of
modes, for example just having the RATE mode available to the user. RATE mode operation
will display the current counter activity rate. MAX mode is used to capture the highest count
rate or activity rate detected – useful for finding a peak rate, or frisking when the display is
not visible. The user can switch between alpha or beta (or alpha+beta) by simply pressing
the Alpha-Beta (α-β) button. COUNT mode allows the user to perform a count for a pre-
determined time. Depending on the count units chosen, the result can be a scaler count
(in counts or disintegrations), or a time-averaged rate (cpm, dpm, Bq, cps). The audio can
be enabled during the COUNT mode, but long pressing the audio button allows the user to
select between commonly used count times.
The instrument features a large backlit LCD (liquid crystal display), an easy, intuitive use
keypad, and audio feedback. The unit body is made of lightweight but durable plastic. It is
intended for outdoor use and can resist splashing water. The foam grip provides a comfort-
able, ergonomic grip but may be removed for ease of decontamination.
The display will be automatically back-lit if light levels are low or can be set to a user defined
light level. The display back-light can also be configured for “Continuous On” operation. All
available operational modes can be silent or utilize a “click” audio.
Setup of the instrument is accomplished through the front-panel buttons, or through Lumic
2 software available from Ludlum Measurements.
Front-panel setup can be disabled via the internal switch on the Model 3002 in order to pro-
tect settings from inadvertent changes. When the settings are protected, the user can view
the settings or modify a limited number of settings as defined with the Lumic software. Us-
ing the Lumic software, the Model 3002 can be configured to allow changes to the alarms
and or count time even when in protect mode.
9

10 CHAPTER 1. INTRODUCTION
The unit is operated with four alkaline AA batteries for operation from -20 to 50 °C (-5 to
122 °F). Battery life is approximately 750 hours (as low as 100 hours w/backlight always on)
under normal usage. A low-battery indicator on the LCD warns when less than 16 hours of
battery life remain.
The Model 3002 comes with the ability to log measurements to memory for later download.
The optional Ludlum Lumic Datalog software is needed to download this memory, however.
The unit can log up to 1000 alpha and beta measurements simultaneously, and it adds a
date/time stamp to each measurement.
There are several options for the Model 3002 , including a headphone jack (for listening to
clicks in noisy environments), a storage or shipping case to securely transport or store your
instrument, and an optional set of rings to fasten a shoulder strap to the instrument for easier
carrying.
The Ludlum Lumic Calibration software is also recommended for calibration of your instru-
ment, since it allows for the reading/writing/printing of all the instrument parameters. It
includes wizards that will assist in calibrating and plateauing detectors. After configuring
the wizard for a specific detector, the wizard will automate much of the data collection and
calculation required for calibration.
For more advanced use: See Appendix A for information on our Auxiliary Communications
features, which allow the instrument to expand its capabilities with a variety of external de-
vices through a standard serial interface.
Ludlum Measurements, Inc.

CHAPTER
2
GETTING STARTED
2.1 Unpacking and Repacking
Remove the calibration certificate and place it in a secure location. Remove the instrument
and ensure that all of the items listed on the packing list are in the carton. Check individual
item serial numbers and ensure calibration certificates match between instruments and de-
tectors (if applicable). The Model 3002 serial number is located on a label on the front side
of the unit.
To return an instrument for repair or calibration, provide sufficient packing material to pre-
vent damage to the instrument during shipment. Every returned instrument must be ac-
companied by an Instrument Return Form, which can be downloaded from the Ludlum web-
site at www.ludlums.com. Find the form by clicking the “Support” tab and selecting “Service
Department” from the drop-down menu. Then choose the appropriate form located under
the "Returned Goods Form" heading.
2.2 Battery Installation
A low-battery indicator appears at the top of the LCD when less than 16 hours of battery life
remain. When this indicator is present, follow these steps to replace the four standard AA
batteries:
1. Turn off power to the instrument.
2. Turn the instrument over so that the bottom of the instrument is facing up.
3. Use a straight, medium-sized screwdriver to turn the single screw on the battery
cover one-quarter turn counter-clockwise.
4. Release and remove the battery cover.
5. Replace all four AA batteries.
6. Replace the cover and turn screw one quarter of a turn clockwise to secure.
11

12 CHAPTER 2. GETTING STARTED
2.3 Instrument Operational Test
Once this procedure has been completed, the instrument is ready for use.
2.3.1 Turning the Instrument On
Turn the instrument ON by pressing the ON/OFF button for about a second, and then re-
leasing. The instrument should activate all the LCD segments and the audio. Observe the
device during this time. If any LCD segments are missing, or audio fails to work, the device
is in need of repair. Please refer to Figure 2.1.
Figure 2.1: Startup Display (All Segments Shown)
The instrument then displays the firmware version. Please refer to figure below.
Figure 2.2: Firmware Version Display
Note: Firmware versions with Bq units are equipped with auxiliary communication.
Beginning with the n20 version firmware, the tick marks below the firmware number define
the board generation, which will help with future firmware updates. Once n20 is installed,
the user will no longer have to open the instrument to determine which version of the main
processor board was used in the instrument. Instead, use the following table to determine
which main processor board is installed in the instrument:
• 1 tick - 5498-901
• 2 ticks - 5519-063
• 3 ticks - 5519-270
Ludlum Measurements, Inc.