Lumascape Linealux L3 LS9031 User manual

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
1 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
LS9031
Linear Facade
Lite
READ ALL SAFETY INSTRUCTIONS FIRST
› Follow instructions carefully, failure to do so will void
warranty.
› Ensure installation complies with local law and
applicable standards.
› Input voltage range 120-277 V
› Only use Lumascape power supply, control
equipment and leader cables.
› Ensure mains input power is surge protected.
› Never make connections whilst the power is
connected.
› Do not make modifications or alter the product.
› Keep luminaire clean and free of debris.
› Connectors are to be kept clean and dry at all times.
› Once installed, all connectors are to be mated and a
terminating plug is required on the last fitting of run.

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
2 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Below is a general overview of a typical LS9031 setup. The Leader Cable (A) connects to the first Luminaire Input (B)
via an IP68 quick connector. The LS9031 is designed for loop-in, loop-out. The output (C) of the previous luminaire
will connect to the input (B) of the next luminaire. At the end of the run the luminaire chain has to be terminated with
a Terminator (H).
Luminaires come with Mounting Brackets (D or E) and Cable Holders (G). Luminaires come in 2 ft and 4 ft length. All
length of luminaires come with two Mounting Brackets (D or E). All 2 ft luminaires come with a single Cable Holder
(G) while 4 ft luminaires are each supplied with four Cable Holders (G).
Mounting Brackets (D or E) and Cable Holders (G) need to be attached to the luminaires before mounting. It
is recommended installers use two SS316 screws per Mounting Bracket (D or E) to secure the luminaire to the
substrate.
Component Overview
A
C
B
D
E
F
ALeader Cable
BLuminaire Input
CLuminaire Output
DAdjustable Mounting Bracket
EFixed Mounting Bracket
FMounting Board
GCable Holder
HTerminator
G
H
or

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
3 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Dimensions
End View Mounting Bracket
Side View
Fixed
Bracket
Adjustable
Bracket
42mm (1.7")
60mm (2.4")
42mm (1.7")
75mm (2.9")
60mm (2.4")
312mm (12.3")
610mm (24.0")
908mm (35.7")
1206mm (47.5")
56mm(2.2")
44mm ( 1.7")
Fixed
Bracket
Adjustable
Bracket
42mm (1.7")
60mm (2.4")
42mm (1.7")
75mm (2.9")
60mm (2.4")
312mm (12.3")
610mm (24.0")
908mm (35.7")
1206mm (47.5")
Fixed
Bracket
Adjustable
Bracket
42mm (1.7")
60mm (2.4")
42mm (1.7")
75mm (2.9")
60mm (2.4")
312mm (12.3")
610mm (24.0")
908mm (35.7")
1206mm (47.5")

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
4 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Step 2
Screw adjustable bracketry to mounting board on underside of luminaire and screw bracket in place. Repeat until
all four screws are firmly in place. Torque: 1.5 N.m.
NOTE: The adjustable mounting bracket is reversible.
Attaching Adjustable Bracket
OR
Step 1
Use allen key to loosen bracket’s tilt mechanism and adjust the tilt of the mounting bracket.
Tighten to lock bracketry in place.
Unlock Adjust Lock

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
5 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Step 1
Attaching Fixed Bracket
Screw fixed bracketry to mounting board on underside of luminaire and screw bracket in place, as pictured.
Torque: 1.5 N.m
Step 2
Clip the cable under the cable holder. Pinch firmly to
remove and reattach Cable Holders. Repeat these
steps for each cable holder on each luminaire.
NOTE: This is not applicable for 1ft luminaires.
Attach Cable Holder

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
6 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Step 4 Repeat the above steps to mount every luminaire in the
chain. When placing the luminaires in and end-to-end setup
be sure to leave a minimum gap of 0.4” (10mm) to allow for
thermal expansion.
Minimum thermal
expansion gap
between luminaires
Minimum
0.4” (10mm)
Mounting the Luminaire
Step 1 It is recommended to mount the luminaire with SS316 Stainless Steel screws. To start put a single
screw into one bracket. Use a spirit level or digital inclinometer to make sure the luminaire is level.
Once the luminaire is level secure with a second screw on the opposing side.
Step 2 Insert the remaining screws required. Each adjustable mounting bracket should be secured with one
SS316 Stainless Steel screw. Each fixed mounting bracket should be secured with two SS316 Stainless
Steel screws.

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
7 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Electrical Connection
Once the physical components have been installed it is time to complete the electrical installation.
QUESTIONS
Contact us at details below
Step 2
Step 1
Power up the circuit to test the installation.
Luminaire to Luminaire
Connect the output of the previous
luminaire to the input of the next
luminaire in the chain. Do this for all
the luminaires within the chain.
Leader Cable
Connect the leader cable
to the input of the first
luminaire in the chain.
Terminator
Attach the terminator
to the output of the last
luminaire in the chain.
Wire Colour Designation
Active Brown
Neutral Blue
Earth Green / Yellow
Data Black
Wire Colour Designation
Active Black
Neutral White
Earth Green / Yellow
Data Grey (or Red)
International Market
North American Market
Mains Voltage

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
8 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Network Topology - PowerSync™ Dimmable
Control Signal
120-277V
50/60Hz
120-277V
50/60Hz
Loop to next PowerSync™
Data Injector
150m (492') max
Combined length of both trunk cables can not exceed 150m (492')
PowerSync™ Topology 1 - Single Trunk Cable
10m (33') max
PowerSync™ Topology 2 - Split Trunk Cable
Maximum Circuit Load
LS6540
PowerSync™
Data Injector
LS6540
PowerSync™
Data Injector
I
I
Up to 45 luminaires per run under the following conditions:
Max total cable run length 150m (492') in up to two trunk cables
For run lengths in excess of 30m (100'), the data wire gauge cannot exceed 14 AWG (2.5mm2)
For run lengths up to 30m (100'), the data wire gauge is not governed
Refer to 'Maximum Circuit Load' table for circuit limitations
Always observe local electrical codes for branch circuit current limitations
Terminator
Use PowerSync™ terminator, supplied with
leader cable to terminate last luminaire
in chain.
T
Maximum Current
≤16.0A through cables and connectors
supplied by Lumascape
≤12.8A applies to connectorised
installations in North America
I
Connection Type
Circuits can be configured as either
connectorised or hardwired. For details
consult installation instructions and comply
with local electrical codes.
T
T
T
Maximum Number of Interconnected Fixtures
Luminaire
Length LED Power 120V 240V 277V
12A 16A 12A 16A 12A 16A
1ft 5W 45 45 45 45 45 45
12W 45 45 45 45 45 45
2ft 5W 45 45 45 45 45 45
12W 40 45 45 45 45 45
3ft 5W 45 45 45 45 45 45
12W 26 35 45 45 45 45
4ft 5W 42 42 45 45 45 45
12W 20 26 40 45 45 45
Refer to PowerSync™ installation manual for maximum distance information and typology options.
All connectorised options in North America are limited to 12.8A branch circuit load.
For non-continuous runs contact factory for details.
Local wiring rules and requirements may limit circuit loadings. Refer to relevant electrical parameters to calculate.

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | Email: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
9 / 9IN0206 N190610
Linealux L3 LS9031
Installation Instructions
Products and specifications are subject to change without notice.
LS9031
Maximum Current
≤16.0A through cables and connectors
supplied by Lumascape
≤12.8A applies to connectorised
installations in North America
I
Connection Type
Circuits can be configured as either
connectorised or hardwired. For details
consult installation instructions and comply
with local electrical codes.
Network Topology - Non-Dimmable
120-277V
50/60Hz
When no data injector is in use
(non-dimming applications),
isolate data wire.
Observe local electrical codes for branch circuit current limitations
- assume 1.5mm2(16 AWG) wire size for International market.
- assume 2.0mm2(14 AWG)wire size for North American market.
Up to 45 luminaires per run under the following conditions:
Refer to 'Maximum Circuit Load' table for circuit limitations
Always observe local electrical codes for branch circuit current limitations
Maximum Circuit Load
I
Maximum Number of Interconnected Fixtures
Luminaire
Length LED Power 120V 240V 277V
12A 16A 12A 16A 12A 16A
1ft 5W 45 45 45 45 45 45
12W 45 45 45 45 45 45
2ft 5W 45 45 45 45 45 45
12W 40 45 45 45 45 45
3ft 5W 45 45 45 45 45 45
12W 26 35 45 45 45 45
4ft 5W 42 42 45 45 45 45
12W 20 26 40 45 45 45
Refer to PowerSync™ installation manual for maximum distance information and typology options.
All connectorised options in North America are limited to 12.8A branch circuit load.
For non-continuous runs contact factory for details.
Local wiring rules and requirements may limit circuit loadings. Refer to relevant electrical parameters to calculate.