Lumencor SOLA SM User manual

SOLA SM and SOLA SM
365 Light Engine®
Instruction Manual
Lumencor, Inc. Document Number 57-10003 www.lumencor.com

Regulatory Models
Lumencor utilizes regulatory model names for all certified and CE marked products. The regulatory model names are
traceable to all regulatory documentation, third party reports and certifications.
“Regulatory Model: Sola” is used as a representative model for all certified and CE marked Sola Products.
Emissions
This equipment has been tested and found to comply with the limits of EMC directive 2014/30/EU and FCC part 15
(CISPR 11:+A1:2016). These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Safety Certifications
TÜV SÜD America, CB Certification (IEC 61010-1:2010)
TÜV SÜD America, NRTLus Certification (UL 61010-1:2012/R:2016-04)
TÜV SÜD America, cNRTL Certification (CAN/CSA-C22.2 No. 61010-1:2012/U2:2016-04)!
TÜV SÜD America, EN Certification (EN 61010-1:2010)!
CE Marking
Low Voltage Directive (2014/35/EU)
EMC Directive (2014/30/EU)
RoHS Directive (2011/65/EU+2015/863/EU)
REACH Regulation (EC) No. (1907/2006/EC)
EU Declarations of Conformity can be found at https://lumencor.com/company/compliance
For EU customers discarding end-of-life Lumencor electrical and electronic equipment: Please submit an RMA request
with “Recycle product under WEEE” in the Description of Issues field.
For disposal in countries outside of the European Union: This symbol is only valid in the European Union (EU). If you wish
to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
Lumencor, Inc. | 14940 NW Greenbrier Parkway | Beaverton, OR 97006 USA | 503.213.4269 | www.lumencor.com!
Document Number 57-10003!
Revision C!
091721!
SOLA SM Light Engine Instruction Manual "2
Lumencor Light Engines as supplied, and as represented in this manual, meet safety and regulatory require-
ments!For Research Use Only.!If the light engine is incorporated into an instrument or system for a specific end-
use application, it is the responsibility of the system integrator to verify that the light engine, and the system into
which it is incorporated, meet all safety and regulatory requirements of that end-use application.

Table of Contents
1. Introduction!
2. Precautions and Warnings!
3. Installation and Operating Instructions!
4. Spectral Output!
5. Product Specifications!
6. Routine Maintenance and Trouble Shooting!
7. Customer Support!
8. Warranty!
SOLA SM Light Engine Instruction Manual "3

1. Introduction
Lumencor’s SOLA SM light engines are designed for laboratory use by bioanalytical researchers and/or developers of life
science instrumentation. SOLA SM light engines generate white light output by combining the outputs of multiple solid
state light sources. The light output on/off status is manually controlled via a rocker switch located on the front panel or
a foot pedal toggle switch accessory (part number 29-10045) that plugs into the 3.5 mm connector on the rear panel.
This manual covers both SOLA SM and SOLA SM 365 light engine models, which are defined by their different
ultraviolet/violet spectral outputs as described in Section 4.
SOLA SM Light Engine Instruction Manual "4

2. Precautions and Warnings {Précautions et mises en garde}
A few simple practices will ensure trouble-free operation for the life of the light engine.
Les quelques règles simples suivantes permettront d’assurer un fonctionnement fiable pendant toute la durée de service
de la source lumineuse.
Safety Instructions:
Please read and follow all safety instructions provided BEFORE using your new SOLA SM light engine. Failure to comply
with the safety instructions may result in fire, electrical shock, or personal injury and may damage or impair protection
provided by equipment. Please save all safety instructions.
Instructions de sécurité:
Veiller à lire et à respecter toutes les instructions de sécurité fournies AVANT d’utiliser le nouveau SOLA SM afin
d’écarter les risques d’incendie, de décharge électrique, de blessure corporelle et de possibles dommages ou défaillance
de la protection offerte par l’appareil. Conserver toutes les instructions de sécurité.
Safety Definitions {Définitions relatives à la sécurité}:
Warning: Statements identify conditions or practices that could result in personal injury.
Avertissement:déclarations qui identifient des situations ou des pratiques susceptibles d’entraîner des
blessures corporelles.
Caution: Statements identify conditions or practices that could result in damage to your equipment.
Attention:déclarations qui identifient des situations ou des pratiques susceptibles d’endommager le matériel.
Safety Items {Mesures de sécurité}:
Warning: DO NOT use an unapproved power supply. The Lumencor-supplied external power supply is
recommended for use with the SOLA SM light engine. Alternative approved/certified 24 V DC power supplies may be
used provided that the current is limited to 5.0 A max. Also, it is imperative that the alternative power supply has output
over-current protection, as the power input of the SOLA SM is not fused. The equipment is required to be supplied by a
properly approved/certified DC power source meeting the minimum electrical ratings of the product. Connect the AC
power cord to a receptacle with a protective safety (earth) ground terminal.
Avertissement!: NE PAS utiliser une alimentation électrique non homologuée. Il est conseillé d’utiliser
l’alimentation électrique externe fournie par Lumencor avec la source lumineuse SOLA SM. Il est possible d’utiliser une
autre CC approuvée/certifiée alimentation électrique continue 24!V à condition que l’intensité soit limitée à 5,0!A
maximum. En outre, il est impératif qu’elle présente une protection de sortie contre les surintensités, car l’entrée
d’alimentation du SOLA SM ne comporte pas de fusible. L'équipement doit être fourni par un / certifié DC réunion de
source d'alimentation correctement approuvé les ratings électriques minimales du produit. Brancher le cordon électrique
sur une prise de courant protégée par une borne de terre.
Warning: DO NOT look into the output of the light engine. The brightness of this light source is higher than most
commercial lighting fixtures and is required to couple directly into a microscope or other bioanalytjcal instrument.
SOLA SM Light Engine Instruction Manual "5

Avertissement: NE PAS regarde directement la sortie de la source lumineuse. L’intensité lumineuse de cette
source est supérieure à celle de la majorité des appareils d’éclairage disponibles dans le commerce et est conçue pour
un raccordement direct à un microscope ou autre appareil de bioanalyse.
Warning: DO NOT turn on the light unless the output end of the light guide is safely!directed!into an enclosed
optical path. "DO NOT point the light output directly onto any flammable or burn-susceptible material."This in-
cludes all animal or vegetable tissues, plastics, fabrics, paper and liquids.!
Avertissement: NE PAS allumer la lumière sans l'extrémité de sortie du guide de lumière dirigée en toute
sécurité dans un chemin optique fermé. NE PAS pointer la sortie de lumière directement sur un matériau susceptible
d'être inflammable ou susceptible de brûler. Cela comprend tous les tissus, les plastiques, les tissus, le papier et les liq-
uides animaux ou végétaux.
RISK GROUP 3
Warning: Possibly hazardous optical radiation emitted from this product. Do not look at operating lamp. Eye injury may
result.
Warning: Infrared (IR) emitted from this product. Do not look at operating lamp.
Warning: UV emitted from this product. Avoid eye and skin exposure to unshielded product.
GROUPE DE RISQUE 3
Avertissement: Infrarouge (IR) émise par ce produit. Ne regardez pas la lampe d'exploitation.
Avertissement: Rayonnement optique Peut-être dangereux émis par ce produit . Ne regardez pas la lampe d'exploita-
tion. Une blessure oculaire peut entraîner.
Avertissement: UV émis par ce produit . Évitez les yeux et la peau exposition au produit non blindé.
Caution: DO NOT open the unit. There are no serviceable parts inside the light engine chassis and opening the light
engine enclosure will void the manufacturer’s warranty.
Attention: NE PAS ouvrir l’appareil. Il ne contient aucune pièce réparable et l’ouverture de son boîtier a pour effet
d’annuler la garantie.
Caution: DO NOT set liquids on the light engine. Spilled liquids may damage your light engine.
SOLA SM Light Engine Instruction Manual "6

Attention: NE PAS placer de liquide sur la source lumineuse. Les liquides renversés peuvent endommager la
source lumineuse.
Caution: DO NOT drop the light engine. It contains glass optical components that could be damaged or misaligned
by the shock produced by a drop onto a hard surface.
Attention: NE PAS laisser tomber la source lumineuse. Elle contient des composants optiques en verre suscepti-
bles d’être endommagés ou désalignés par le choc résultant d’une chute sur une surface dure.
DISCLAIMER: Lumencor shall not be liable for injury to the user or damage to the product resulting from the
SOLA SM light engine being used in a way for which it was not intended and in complete disregard for any
posted safety precautions and warnings.
AVIS DE NON-RESPONSABILITÉ: Lumencor décline toute responsabilité pour les blessures corporelles ou
les dommages au produit résultant d’une utilisation du SOLA SM autre que celle prévue et du mépris total de
les mesures de sécurité et mises en garde affichées.
SOLA SM Light Engine Instruction Manual "7

3. Operating Instructions!
3.1 Contents
The SOLA SM light engine ships with the following list of standard components:
1. SOLA SM light engine configured with an output adapter for coupling to a
3 mm diameter liquid light guide.
2. A 24 V /5 A DC power supply (Lumencor part number 27-10001).
3. A region-specific 6 ft AC power cord for the power supply (see adjacent
table).
The model name and unique 4- or 5- digit serial number of the light engine are
marked on a label affixed to the back panel (Figure 1). SOLA SM 365 light engines are identified by a model name
containing “V” (e.g. SOLA SM 5-LCR-VA, Figure 1) and a UV marking on the rear panel (Figure 1). Performance
specifications for individual light engines are listed on the certificate of conformance included with the shipping
documents e-mailed to the customer. It is important to retain the certificate of conformance for reference. In the event
that the light engine is sold or transferred, the certificate of conformance should be conveyed to the new owner.
3.2 Installation
NOTE: Any end-product/system incorporating or
coupled to a Lumencor Light Engine shall be fully
evaluated to verify all applicable safety and regulatory
compliance requirements prior to use.
SOLA SM light engines incorporate fan-assisted air
cooling. When positioning the SOLA SM for use, place
the unit on a hard surface and avoid blocking or
restricting airflow at the air intake (front panel) and
exhaust ports (rear panel; Figure 1). The light engine
must be operated in a non-condensing environment
(dew point <10ºC with controlled ambient temperature
<30º C). Restricting the airflow will cause the unit to
operate at elevated temperatures and will result in
decreased operating lifespan and/or premature failure.
Position the unit in an orientation that allows
unrestricted access to the DC power connector at the
back of the light engine. In an emergency, you may
need to disconnect power to the unit quickly. The
rocker switch in the top left corner of the rear panel
controls electrical power to the unit. A green LED
above the switch indicates that power to the light
engine is ON. Refer to Figure 1 for the rear panel
locations of the input DC power connection, the foot pedal connection and the master electrical power switch. Note that
the foot pedal is an on/off toggle switch. Its on/off status cannot be determined from its position. Before connecting the
foot pedal, make sure the electrical power switch (Figure 1) is in the OFF position to avoid unintentional initiation of light
SOLA SM Light Engine Instruction Manual "8
AC Power Cords
Region
Part Number
North America
29-10002
Europe
29-10005
United Kingdom
29-10004
Israel
29-10008
Australia/New Zealand
29-10024
Figure 1. SOLA SM 365 light engine rear panel
Model and Serial
Number
identification label
Air cooling
exhaust fan grill
Power switch and
indicator LED

output. After connecting the foot pedal, and with the light guide output safely directed into an enclosed optical path (e.g.
microscope input collimator or a beam dump), turn the power switch ON to begin operation.
WARNING: Prior to turning the light output on, be sure the output end of the liquid light guide or optical fiber is safely
directed into an enclosed optical path (e.g. a beam dump).
AVERTISSEMENT!: avant d'activer la sortie de lumière, assurez-vous que l'extrémité de sortie du guide de lumière liq-
uide ou de la fibre optique est dirigée en toute sécurité dans un chemin optique fermé (par exemple, une décharge de
faisceau).
The SOLA SM light engine has a safety interlock for the light guide that prevents light output unless a liquid light guide is
fully inserted into the light guide port. Before operating the unit, make sure the 3 mm diameter liquid light guide is
properly installed in the light guide port (Figure 2). The set screw should be loosened using a 2 mm hex wrench so the
light guide slides all the way into the receptacle without obstruction. Once the light guide is fully inserted, lightly tighten
the set screw to hold it in place and prevent inadvertent disconnection. Prior to turning the light on, be sure to remove
the red dust caps from the liquid light guide and direct its output into an enclosed optical path (e.g. microscope input
collimator or a beam dump). Do not bend the light guide beyond its specified minimum bending radius (40 mm or 1.6
inches). Extreme bending of the light guide may cause permanent deformation, resulting in decreased light transmission.
Take necessary precautions to protect yourself and others from the high intensity light when turning on the
unit.
3.3 Operation!
The SOLA SM light output can be turned on or off using the manual light output switch on the front panel or using the
foot pedal toggle switch accessory. Do not combine the operation of these switches. If the front panel rocker switch is
used to turn the light on, that same switch should be used to turn it off. If the foot pedal is used to turn the light on, the
foot pedal be used to turn the light off. An amber indicator LED above the manual light output switch indicates active
light ouput. There is no warm-up time; the light engine output stabilizes less than 1 second after the manual light output
switch is moved to the “on” position. Light output can be switched off during intervals when it is not required for active
viewing or data collection. After light output is switched off, the cooling fan will continue to run for 5 minutes, after which
it will automatically stop until light output is turned back on. Light output is set to a single maximum intensity level.
SOLA SM light engines do not provide electronically-controlled output attenuation.
In the event that the liquid light guide becomes disconnected from the unit during operation, the safety interlock will be
opened and light output will cease immediately. In order to turn the light output back on, you will need to: 1) turn the
electrical power off, 2) fully insert the light guide into the light guide port, 3) turn the electrical power back on and then 4)
activate light output using either the front panel rocker switch or the foot pedal toggle switch.
SOLA SM Light Engine Instruction Manual "9

4. Spectral Output
Typical spectral output distributions of SOLA SM and SOLA SM 365 light engines are shown below (Figure 3).
5. Product Specifications!
SOLA SM light engines must be operated and stored within the specified environmental conditions. Performance
specifications for individual light engines are listed on the certificate of conformance included with the shipping
documents e-mailed to the customer. It is important to retain the certificate of conformance for reference. In the event
that the light engine is sold or transferred , the certificate of conformance should be conveyed to the new owner.
Certificates of conformance are also recorded in Lumencor’s database and copies can be requested by e-mail to
[e-mail]. The request message must include the 4- or 5- digit serial number of the light engine.
Specification
Detail
Temperature
Operating
32 to 95° F (0 to 35° C)
Non-operating
-4 to 158° F (-20 to 70° C)
Humidity
Operating and non-operating
0 to 80% relative humidity, non-condensing
Altitude
Operating
0 to 10,000 feet (3,048 meters)
Non-operating
0 to 45,000 feet (13,176 meters)
SOLA SM Light Engine Instruction Manual "10
Figure 3. SOLA SM and SOLA SM 365 light engine spectral output distributions.

6. Routine Maintenance and Trouble Shooting
No routine maintenance is required. There are no user-replaceable components or sub-assemblies in the SOLA SM light
engine. Opening the light engine enclosure will void the manufacturer’s warranty. In the event that the light engine fails to
perform in accordance with the specifications listed on the certificate of conformance, please contact Lumencor
Technical Support for assistance, as directed in Section 7.
7. Customer Support!
For technical support of SOLA SM and SOLA SM 365 light engines, please contact Lumencor by phone at
503.213.4269 or via e-mail at [e-mail]. Please be prepared to provide the 4- or 5-digit serial number
of the light engine (see Figure 1), a description of the problems encountered and information on the usage context (e.g.
what microscope is being used). This information will help to determine whether the problems can be resolved in situ by
adjustments to the system configuration, or whether a fault has developed in the light engine that requires its return to
Lumencor’s facility in Beaverton, Oregon for evaluation and, if necessary, repair. Any light engine return to Lumencor for
service or repair requires a material authorization (RMA) number. To request an RMA number, fill out and submit the
online request form. It is the customer’s responsibility to properly package and safely ship products to Lumencor.
Instructions for shipping will be provided in the e-mail giving notification of the RMA number.
8. Warranty!
SOLA SM and SOLA SM 365 light engines come with a 18 month warranty, starting on the original date of shipment from
Lumencor. Light Engines qualifying for warranty service must be verifiably delivering performance that is substantially at
variance with the levels documented in the certificate of conformance. The light engine must also have been used and
maintained under operating conditions consistent with the specifications given in Section 5, and observing all the
Precautions and Warnings notified in Section 2. This warranty does not extend to light engines that have been subject to
misuse, accident, tampering or improper installation. Accessories including (but not limited to) liquid light guides, optical
fibers, collimators, cables and control consoles are not covered by the warranties attached to light engines. Please fill out
and submit the online warranty registration form . This will facilitate provision of warranty service should it be required.
Dimensions (W x L x H)
4.9 in x 10.4 in x 6.40 in / 12.5 cm x 26.3 cm x 16.3 cm
Weight
8.0 lb / 3.6 kg
Input Power Requirements
24 V DC / 5.0 A, 120 W maximum, power supply included
Power consumption
90 W (light output on); 3 W (light output off, fan on)
Warm-up Period
1 s
Protection
IP Rating of X0
Sound Level
Sound Level at 1 m < 10 db(A)
Connections
3.5 mm foot switch (optional accessory)
Warranty
18 months parts and labor
Specification
Detail
SOLA SM Light Engine Instruction Manual "11