Lumi Oasis 5445 User manual

www.lumi-o.com
OASIS #5445
STAINLESS STEEL HANDRAILS INSTALLATION WITH BRACES:
Step 1
fig.1
1- Slide the braces in the top of the handrails . Lay the step on the side and fix both handrails on the step with the 3”bolt for the upper
holes (4), the 3 ½”for the lower holes(4) ,the nuts (8) and the washers(16). (fig.1)
2- Fill the ballast unit with sand, seal with the plastic cap and put the ballast unit at the appropriate place on the step. (annex a)
3- Move the step into the water and allow the air to escape. Place the step by the pool wall leaving at least 1”between the step and the wall.
Ensure that the step touches the ground solidly. Lower the braces until its rests on the sidewalk. (annex b)
4- Affix the braces on the sidewalk with concrete screws (not included ). (annex c)
PVC HANDRAILS INSTALLATION :
1- Lay the step on the side and fix the PVC tubes on the step with the 3”bolt
for the upper holes (4), the 3 ½” for the lower holes(4), the nuts (8) and the washers(16). (fig.1) Slide one brace on each of the rear
PVC posts. (Upper step)
2- Affix the handrails on the support tubes with the ¾” screws(4). (fig.2)
3- Fill the ballast unit with sand, seal with the plastic cap and put the ballast unit at the appropriate place on the step. (annex a)
4- Move the step into the water and allow the air to escape. Place the step by the pool wall leaving at least 1”between the step and the wall.
Ensure that the step touches the ground solidly. Lower the braces until its rests on the sidewalk. (annex b)
5- Fix the braces on the sidewalk with concrete screws (not included ). (annex c)
Stepp 2
Handrail
PVC tube
fig.2
Step 1
fig.1
Brace PVC
tube
PVC
tube
3" Bolt (top)
3½" Bolt (bottom)
4x4x10x10x18x
¾ Screw
3”Bolt
3½” Bolt
Additional Material
PVC handrails
- 4 x 39’’ PVC tube
- 4 x 3/4” screw
Stainless steel handrails
- Sand
Note: you may need
approximately 100 lbs of sand
Not included:
Helpful hint:
To ease the installation of the rails and
bolts, use a screwdriver to line up holes.
- Concrete screws
2x Brace
- 2 x handrail
- 2 x plastic cap
- 2 x 3" bolt
- 2x Flange
- 2 x nut
Handrails box content:
Please choose one of the following installation according to your handrails and pool type.
Installation
Read carefully the cautions and every steps before assembly and using your step.
Caution : File off all stripped or sharp edges before assembly to avoid injuries and pool damage.
Rev. 2011-01-06 p.1

Annex B Annex C
Annex A
Sand
Balast
STAINLESS STEEL INSTALLATION WITH FLANGES:
Step 1 Step 2
fig.2
1- Fill the ballast unit with sand and seal with the plastic cap.
(annex a)
2- Move the step into the water and allow the air to escape . Put the
ballast unit at the appropriate place on the step. Place the step by
the pool wall leaving at least 1”between the step and the wall.
Ensure that the step touches the ground solidly.
3- Mark the holes location. (fig.2) NOTE : If the holes do not align, make
the appropriate hole using a 3/8 inch metal drill bit.
4- Take the ballast and the step out of the water. Fix both handrails,
using the back holes of the step, with the 3” bolts for the upper
holes (4), 3 ½”for the lower holes (4), nuts (8) and washers (16). (fig. 2)
5- Put the step back in the water following the procedures from step 2
(fig.3)
6- Anchor the flanges into the sidewalk with concrete screws
(not included) (fig. 4)
7- Screw the handrails to the flanges with the 3`` bolts (2) and nuts (2).
(fig.4)
Step 3
fig.1
fig.3
Step 5
fig.4
Nothing replaces parental
supervision-Watch children
at all time.
Remember:
1- When adding water in your pool,
insert the nozzle of your hose in the
side holes of the step to allow a
good water circulation throughout
the season.
2- When treating your water do not
forget to treat the water inside
your step.
Step maintenance:
CAUTION
:: Do not jump or dive from the step or ladder.
:: The step should be removed from the water when temperature drop below freezing.
:: Never lift the step by its rail.
:: Use battery-operated tools to avoid electric shock near water
:: Ensure no corrosive materials are added to the step, ladder or hardware kit
:: The step and ladder shall be installed per manufacturer’s instructions.
:: The manufacturer is not responsible for damage or injuries caused by improper installation
or use.
:: For special installation, contact your dealer.
:: For more protection, we suggest to install a step pad (not included) under the step.
p.2
Rev. 2011-01-06