Lumi WEDDING CAKE II User manual

fig.3
Step 3
THE WEDDING CAKE II Installation
fig.2
Étape 2
fig.5
Step 5
fig.4
Step 4
Brace (short)
Ramp
Support tube
(long)
Rev. 2007-11-20
Helpful hint: to ease the installation of rails and bolts, use a screwdriver to line up holes.
Material included:
16x Plastic cap (4)
Ramp
Brace
Support tubes
#1
#2
Support tube
- Automatic screwdriver
- Pair of grip
Required tools:
Not included:
4“ flat head bolt
Finished washer
Nut
Locknut
¾“ screw
½” flat head bolt
1½” screw
3“ bolt
9x 9x 4x 4x 7x 5x 2x
#3
Washer
4x
Step 2
- Cisor
4- Place the shorter support tube
in the opening at the top of the step.
Line up the holes and fix the support
tube with the 3” bolts (2), washers (4),
and locknuts (2) included using the
opening in the back. Slide the brace
on the upper support tube (fig. 4).
1- Install 2 protective foam pads
under each reinforcement parts. Fill the 3
reinforcement parts of pea gravel*,
following quantities as shown on (fig.1).
Install the plastic caps.
5- Insert the ramp on both
support tubes. Fix the ramp to the
support tubes with ¾” screws (4).
(fig.5).
2- Lay the step and fix the
reinforcement 1 and 2 at the appropriate
places with the 1 ½ flat head bolts (6),
washers (6), finished washers (6) and
nuts (6). Fix the reinforcement #3 with
4” flat head bolt(2), 1 ½ flat head bolt (1),
washers (2), finished washers (3), and
nuts (3).
Step 6
fig.6
Ballast
6- Cut and dispose the nylon
strap placed to retain the ballast unit
with pea gravel*, seal with the plastic
cap. (fig. 6).
fig.1
Reinforcement 2
Reinforcement 1
Reinforcement 3
Max. qty.
Step 1
Fill completely
Foam pad (6)
- Pea gravel
Note :You will need approximately
150 lbs of pea gravel.
- Shim
3- Lay the step on the flat side
and insert the longer support tube in
the opening at the bottom of the step
and fix it with the 3” bolts (2), washers (4)
and locknuts (2) included and raise up
the step (fig.3).
p.1
Read carefully the cautions and every steps before assembly and using your step.
Caution : File off all stripped or sharp edges before assembly to avoid injuries and pool damage.

STEP MAINTENANCE
Lumi-O Industries Inc. Saint-Jérôme, Québec, Canada J7Y 4E5
Holes
8- Attach the brace to the deck
using the 1¾” screws. If the deck is
above the toprail, attach the brace
directly to the deck (fig.8).
9- If the deck is lower than the
pool, the brace should be shimmed*
to attain the same level as the pool
(fig.9). Ensure the shim is properly
secured to the deck.
10- If the pool is lower than the
deck, the brace should be shimmed*
to attain the same level as the deck.
Ensure the shim is properly secured
to the toprail (fig.10).
Step 10
fig.10
fig.9
Step 9
fig.8
Step 8
www.lumi-o.com
This model require a maximum inclination of the bottom
of the swimming pool of approximately 2 degrees.
*Not included with the step.
STEP MAINTENANCE
Remember:
Nothing replaces
parental supervision
Watch children at all
time.
fig.7
Step 7
7- Move the step into the water
and allow the air to escape. Place the
step against the pool wall and ensure
that the step touches the ground
solidly.
Leave 1” gap between the
pool wall and the back of the step.
Lower the brace until its rests on the
deck. Put the ballast unit on top of the
step (fig.7).
Rev. 2007-11-20 p.2
1 - When adding water in your pool, insert the nozzle of your hose in the side holes of the step to allow a good water
circulation throughout the season.
2 - When treating your water, do not forget to treat the water inside your step.
CAUTION
:: Install the step on a solid base and at base.
:: Do not jump or dive from the step.
:: The step should be removed from the water when
temperature drop below freezing.
:: Never lift the step by its rail.
:: Use battery-operated tools to avoid electric shock near water
:: Ensure no corrosive materials are added to the step or
hardware kit
:: The step shall be installed per manufacturer’s instructions.
:: The manufacturer is not responsible for damage or injuries
caused by improper installation or use.
:: For more protection, we suggest to install a step pad* under
the step.
Call your pool supply for more information.