Luminaire led LVP58 User manual

INSTALLATION GUIDE FOR
LVP58 LED SERIES
RETAIN THESE INSTRUCTION FOR FUTURE USE
One Lithonia Way, Conyers GA 30012 | 1.800.705.SERV (7378) | www.luminaireled.net | © 2020 Acuity Brands Lighting, Inc. All rights reserved.
Page 1of 3
SAFETY PRECAUTIONS
WARNING - Risk of fire or electric shock. Basic safety precautions should always
be followed when using electrical equipment.
WARNING - This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of the
product and the hazards involved.
WARNING - Disconnect power to all circuits before wiring fixture.
WARNING - Install in accordance with all national, state, and local codes.
WARNING - Do not connect to an ungrounded supply.
WARNING - Read all fixture markings and labels to ensure correct installation of
fixture.
WARNING –Do not apply power to the fixture until the LED Board assembly is
connected to the driver. If power is applied to the fixture prior to connecting the
LED Board assembly to the driver, this will cause the LED Board to fail and void
the warranty.

INSTALLATION GUIDE FOR
LVP58 LED SERIES
RETAIN THESE INSTRUCTION FOR FUTURE USE
One Lithonia Way, Conyers GA 30012 | 1.800.705.SERV (7378) | www.luminaireled.net | © 2020 Acuity Brands Lighting, Inc. All rights reserved.
Page 2of 3
CAN ICES-005 (A) / NMB-005 (A)
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
ISED CANADA STATEMENT / DECLARATION POUR ISDE CANADA
This class A lighting equipment complies with Innovation, Science and Economic
Development (ISED) Canada Standard for radio interference-causing equipment
ICES-005, 5th edition.
Ce matériel d’éclairage de classe A est conforme avec la norme sur le matériel
brouilleur radio NMB-005, 5ième édition, publié par innovation, science et
développement économique (ISDE) Canada.

INSTALLATION GUIDE FOR
LVP58 LED SERIES
RETAIN THESE INSTRUCTION FOR FUTURE USE
One Lithonia Way, Conyers GA 30012 | 1.800.705.SERV (7378) | www.luminaireled.net | © 2020 Acuity Brands Lighting, Inc. All rights reserved.
Page 3of 3
INSTALLATION PROCEDURE
1. Remove Luminaire from carton and inspect for damage.
2. Remove Lens (see Figure 1) and/or Shroud (see Figure 2) by loosening (2) 8-32 screws. Set aside for
later use.
3. Remove LED Board Assembly by loosening (4) 8-32 screws (see Figure 3).
4. Disconnect Driver wires to LED Board Assembly. Set wire nuts aside for later use.
5. Apply rectangular gasket to back of fixture.
6. Mount fixture to surface using (2) ¼”hardware (see figure 4, hardware not included).
7. Connect all supply wires in accordance with national and local electrical codes.
8. Reconnect Driver wires to LED Board Assembly using supplied wire nuts from Step 4.
9. Re-install LED Board Assembly using 8-32 hex screw. Do not over tighten.
10. Re-install Lens and/or Shroud.
11. Energize and test.
Lens Screws
Figure 1 - LVP58
Figure 2 - LVP58 LPL
Figure 3 –LVP58 Reflector
Figure 4 –LVP58 Backbox
LED Board
Assembly Screws
Mounting Holes
LPL Lens Screws