Lumingen SLD-LN Series User manual

IMPORTANT SAFETY INSTRUCTIONS Mesures de Sécurité à Respecter
This product must be installed in accordance with the applicable installation code by a person familiar with the
construction and operation of the product and the hazards involved. Ce produit doit être installé selon le code
d’installation pertinent, par une personne qui connaît bien le produit et son fonctionnement ainsi que les risques inhérents.
Twist-on wire connectors are not re-usable. Replace only with weather-proof twist-on wire connectors. Twist-on wire
connecteurs ne sont pas réutilisables. Utiliser des connecteurs seulement intempéries.
DRY/DAMP
LOCATIONS

Data subject to change without notice.
Accessed Date: February 16, 2018
Visit us at www.lumingen.com or Call us at 1.604.371.4112
Lumingen Technologies, Ltd.
Page 2
SLD-LN-xxxx Specifications...................................................................................................................................................................................................3
Overview ................................................................................................................................................................................................................................3
Electrical Installation ................................................................................................................................................................................................................4
Overview ................................................................................................................................................................................................................................4
Standard Wiring Schematic..............................................................................................................................................................................................4
General Installation ..................................................................................................................................................................................................................5
Overview ................................................................................................................................................................................................................................5
Assembly Procedure...........................................................................................................................................................................................................5

Data subject to change without notice.
Accessed Date: February 16, 2018
Visit us at www.lumingen.com or Call us at 1.604.371.4112
Lumingen Technologies, Ltd.
SLD-LN-xxxx Specifications
Page 3
Model Number
SLD-LN-0030
SLD-LN-0040
SLD-LN-0060
SLD-LN-0100
SLD-LN-0120
Dimensions
(cm)
56 x 10 x 6
87 x 10 x 6
117 x 10 x 6
117 x 10 x 6
117 x 10 x 6
Lumen Output
(Lumens)
4,020 lm
6,100 lm
7,900 lm
15,080 lm
16,800 lm
Power Rating
(Watts)
27 W
41 W
53 W
104 W
120 W
Input Voltage
(Volts AC)
100/277/347 VAC
50/60 Hz
100/277/347 VAC
50/60 Hz
100/277/347 VAC
50/60 Hz
100/277/347 VAC
50/60 Hz
100/277/347 VAC
50/60 Hz
Operating Temperature
(degree Celsius)
-40 ˚C to +50˚C
-40 ˚C to +55˚C
-40 ˚C to +55˚C
-40 ˚C to +55˚C
-40 ˚C to +55˚C
Weight
(kilogram)
1.20 kg
1.99 kg
2.57 kg
2.94 kg
2.94 kg
Listing: cCSAus Certified. Suitable for Dry and Damp Locations. DLC QPL Listed. E.Catalog Listed.
Lensing Material: Optically-clear or diffuse (frosted) polycarbonate lensing.
Housing: Aluminum extrusion, powder-coated white; ABS plastic endcaps

Data subject to change without notice.
Accessed Date: February 16, 2018
Visit us at www.lumingen.com or Call us at 1.604.371.4112
Lumingen Technologies, Ltd.
Electrical Installation
Page 4
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the
hazards involved. Ce produit doit être installé selon le code d’installation pertinent par une personne qui connaît bien le produit et son fonctionnement ainsi que les
risques inhérents.
Twist-on wire connectors are not re-usable. Replace only with un-used twist-on connectors. Remplacer uniquement avec de nouveaux twist-on connecteurs de fils.
LED V- (BLACK 18AWG)
LED V+ (RED 18AWG)
AC/LINE 100/277VAC (BLACK 14AWG)
AC/NEUTRAL (WHITE 14AWG)
GROUND (GREEN-YELLOW/GREEN 14AWG)
To LED Engine
(for reference
only)
AC Supply
Connection
Figure 1—Color coding of the wiring for the luminaire.

Data subject to change without notice.
Accessed Date: February 16, 2018
Visit us at www.lumingen.com or Call us at 1.604.371.4112
Lumingen Technologies, Ltd.
General Installation
Page 5
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the
hazards involved. Ce produit doit être installé selon le code d’installation pertinent par une personne qui connaît bien le produit et son fonctionnement ainsi que les
risques inhérents.
Twist-on wire connectors are not re-usable. Replace only with un-used twist-on connectors. Remplacer uniquement avec de nouveaux twist-on connecteurs de fils.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Figure 2—series of 3 images to the left. On the
long-side of the luminaire, remove the screws
located along the center-line of the assembly.
This allows internal access to the luminaire.
Exercise caution when opening the luminaire.
Figure 3—remove the desired knock out plugs to allow
access for the AC-power conduit. Attach the appropriate
strain relievers for the conduit or cabling.
Figure 5—following the electrical
installation guidelines, wire the AC-
power to the luminaire. Ensure the main
power is off, AC line is not energized,
and correct polarity is observed during
installation.
Figure 6—series of 3 images to the left. Once
installation is complete, close the luminaire, and
replace the locking fasteners that securely closes
the luminaire enclosure.
Swings Open
Locking Fastener
(1pc or 2pcs)
Knock Out Plugs (3pcs)
Figure 4—determine the appropriate hole locations to
mount the fixture. Below is a view of the back piece of the
fixture from the inside. Please verify the proper installation
method with your contractor.
Surface/Suspension
Holes
Surface/Suspension
Holes
Pendant/Junction Box
Holes

Data subject to change without notice.
Accessed Date: February 16, 2018
Visit us at www.lumingen.com or Call us at 1.604.371.4112
Lumingen Technologies, Ltd.
General Installation
Page 6