Lutron Electronics VIMCO Sivoia SV-CCI-GRP User manual

SV-CCI-GRP
Contact Closure Interface
24V~, Class 2/PELV
MDU TERMINAL BLOCK
1 2 3 4 5 6 7 8
J2
1 - Momentary Raise
2 - Open
3 - Momentary Lower
4 - Close
5 - Preset 1
6 - Preset 2
7 - Preset 3
8 - Preset 4
9 - Common
MDU Pin 1
(Cntrl 1)
MDU Pin 2
(Cntrl 2)
24VAC
Dry Contact
Closure Interface
Class 2
SV-CCI-GRP
Coopersburg, PA USA
®
Control Wire:
2 conductor
22–24 AWG
Comm
Link
Power
Supply
Motor Drive Unit (MDU)
OUTPUT
INPUT
AC 1 E GND AC 2 MUX COM MUX CNTRL 2 CNTRL1
Figure A
Description
The Sivoia®Contact Closure Interface (SV-CCI-GRP) con-
trols a user selectable GROUP of shades. This interface
control can be used with devices that have momentary
relay type DRY contact closure outputs. The SV-CCI-GRP
cannot be used with devices providing open collector tran-
sistor outputs. For open collector transistor output devices,
use the SV-GRXI. One SV-CCI-GRP is required for each
GROUP of shades that is to be controlled together. Shade
GROUPS are configured on each Motor Drive Unit (MDU).
One DRY contact closure is required for each control func-
tion (for example: OPEN is one function, CLOSE is another
function). To program the PRESETS, maintain the appropri-
ate closure for a minimum of 4 seconds.
Important Notes
1. Install in accordance with all applicable regulations.
2. Do not connect high voltage power to device.
Improper wiring can result in personal injury or damage
to the device or to other equipment.
3. The SV-CCI-GRP interface is wired to any single MDU
in the group it is controlling.
4. Up to 9 keypads and/or interfaces can be parallel wired
to 1 MDU.
5. Do not connect a contact closure input to more than one
SV-CCI-GRP.
6. The SV-CCI-GRP requires an input closure duration
between 0.1–2 seconds.
Installation
1. Mount the SV-CCI-GRP interface to any indoor surface
using the supplied screws. Mount in a clean, dry location
where temperature will remain between 0°C and 40°C.
Do not mount in an area of excessive moisture.
2. Run the control wire (2 conductor, 22–24AWG) from the
MDU to the SV-CCI-GRP interface. See Figure A.
3. Strip insulation 3/8" from wires.
Note: Closing any contact closure while the shade(s)
are moving will stop the shade(s).
Operation
When a contact closure is selected, the SV-CCI-GRP will
activate the corresponding control function.
Easy Preset Programming
1. Adjust shade(s) to desired position.
2. Close and hold the contact closure for a minimum of 4
seconds. “Pr”will be displayed on all MDU's in that
group indicating the contact closure was programmed.
Note: The Open and Close contact closures can also
be reprogrammed as presets.
Operating Instructions
Please Leave for Occupant
Motorized Shade Systems
®
shading solutions byVIMCOTM
4. Connect Cntrl 1 on the SV-CCI-GRP to CNTRL1 on the
MDU and Cntrl 2 on the SV-CCI-GRP to CNTRL2 on
the MDU using the 2 conductor control wire
5. Connect each contact closure input with respect to com-
mon as shown below in the wiring diagram.

Problem Causes Remedies
Sivoia®Motor Drive Unit power is OFF.
The SV-CCI-GRP may be wired incorrectly
to the Sivoia Motor Drive Unit.
The closure for the desired PRESET was
held for less than 4 seconds.
The SV-CCI-GRP may be wired incorrectly
to the Sivoia Motor Drive Unit.
Sivoia Motor Drive Unit(s) has its presets
locked out.
The SV-CCI-GRP wires are reversed.
Contact closures inputs do
not operate shade(s).
Presets are not being saved.
Open and Raise closures
close or lower the shade:
Close and Lower closures
open or raise the shade.
Restore power.
Ensure SV-CCI-GRP is wired correctly to the Sivoia
Motor Drive Unit as per the wiring diagram above.
Apply and maintain the contact closure of the desired
PRESET for at least 4 seconds.
Ensure SV-CCI-GRP is wired correctly to the Sivoia
Motor Drive Unit as per the wiring diagram above.
Refer to the Sivoia Motor Drive Unit installation sheet.
Ensure SV-CCI-GRP is wired correctly to the Sivoia
Motor Drive Unit as per the wiring diagram above.
Troubleshooting
VIMCO
11520 Sun Shade Lane
Ashland, VA 23005
Made and printed in the U.S.A. 3/03 P/N 040-165 Rev. C
Technical Assistance
If you need assistance, call the toll-free VIMCO Technical Support
Center. Please provide exact model number when calling.
[phone] (U.S.A., Canada, and the Caribbean)
Other countries call [phone]
Fax [phone]
Visit our web site at www.vimco.com
Limited Warranty
VIMCO will, at its option, repair or replace any unit that is defective in materials or manufacture
within one year after purchase. For warranty service, return unit to place of purchase or mail to
VIMCO at 11520 Sun Shade Lane, Ashland, VA 23005, postage prepaid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED
WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS
WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL, OR REINSTAL-
LATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE RESULTING
FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCI-
DENTAL OR CONSEQUENTIAL DAMAGES. VIMCO'S LIABILITY ON ANY CLAIM FOR DAM-
AGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTAL-
LATION, DELIVERY, USE, REPAIR, OR REPLACEMENT OF THE SHADING SYSTEM SHALL
NEVER EXCEED THE PRICE PAID FOR THE SYSTEM.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty may last, so the above limitations may
not apply to you.
This product may be covered under one or more of the following U.S. patents: 5,671,387;
5,848,634; 6,100,659; 6,201,364; 6,313,588; 6,346,781; and corresponding foreign patents. U.S.
and foreign patents pending.
Lutron, Sivoia and the Sunburst logo are registered trademarks of Lutron Electronics Co., Inc.
VIMCO, and shading solutions by VIMCO are trademarks of Virginia Iron & Metal Company, Inc.
© 2003 Virginia Iron & Metal Company, Inc.
shading solutions byVIMCOTM