Lyfco Backviken 166-1-64 User manual

ASSEMBLY MANUAL
BRUKSANVISNING
Model name: Bäckviken
Modellnamn: Bäckviken
SKU: 166-1-64
Konsumentkontakt
Arc E-commerce AB
Box 3124
13603 Haninge
XX-YYWW
Please don’t remove the batch code sticker at back side of this product!
Any feedback please take picture of this batch code for traceablity purpose
NOTE: 50% TIGHTEN BEFORE FIXING ALL BOLTS
VIKTIGT – LÄS MONTERINGSANVISNINGARNA NOGA INNAN DU BÖRJAR
Ta inte bort ettiketten med batchnummer som finns på möbeln. Om du behöver hjälp med service eller reklamation av din möbel –
ange möblensbatchnummer till återförsäljaren, så att du kan få rätt reservdelar till just din möbel.

Attention! Please note that at first all screws should be inserted slightly by hand!
Turn 2-3 times so that the screw grips on its own and connects all elements loosely. The screws
must only be driven in tightly when all elements are connected with each other in this way.
Otherwise the setup won´t be possible. Only by driving them in tightly afterwards, small
deviations of the borehole or the welded joints, which always occur with handcrafted products,
can be compensated.
Notes on an optimized assembly:
Before you completely tighten the screws, check carefully all the screws and tighten them
(only) to the extent that the product remains (especially chairs or loungers) still under load. If
you are sure that your product can withstand load, place it on a solid, level ground and put
some weight on it, please carefully and always with cushions. The various components can then
align with each other. Then tighten completely the screws. Thus you achieve and optimal
alignment of the product and prevent wobbling. Don’t sit, find some weight.
Your new product was made by hand.
Slightly irregularities are rather seen as a
quality attribute than as a reason for
complaints.
Tip: Always fully insert the hex key inside
designated notch of screw.
If you don´t do that and slip out of the
screw, the screw will suffer damage and it
can caused the screw head to become
round inside you won´t be able to find grip
with the hex key anymore!
VIKTIGHT
Don´t use this product if parts are missing, damaged or
worn down.
Don´t use any electronic tools to set up these product.
The high energy of these electronic tools will cause
screw overg ten and therefor they won’t grid.
Don´t overg ten screwws or bolts. Only ten the
screws enely aaer the product is completely set up.
You shouldn’t sit or stand on it.
Don´t let your product stand in the rain. Protect it from
weather impacts. In mes of feeze and over the
winter, we suggest you to store the product in a
covered dry place.
Var uppmärksam! Sätt först i samtliga skruvar löst. Dra inte åt, för då finns risk att skruvhålen inte
passar.
Innan du drar åt skruvarna helt, gör såhär för bästa resultat:
Ställ möbeln på en helt slät yta och lägg ett tillräckligt tungt föremål (ca 10-15kg) på den, så att
alla ben nuddar marken. Skruva därefter i skruvarna helt. Obs – använd inte din kroppstyngd, då
det är för mycket vikt. Om du följer dessa råd, blir din möbel stabil.
Om du inte följer dessa instruktioner kommer möbeln att bli ostadig och ”vickig” då produkten
upplevs ojämn.
Din nya möbel är handgjord. Små avvikelser
kan därför förekomma och är ett
kvalitetsattribut snarare än ett fel.
Tips: Var noga att alltid sätta in insexnyckeln
helt ner i skuven.
Om du inte gör det finns risk att insexnyckeln
slinter, vilket skadar skruven.
Skruvenkandåbliobrukbar.
Använd inte den här produkten om delar saknas,
är skadade eller utslitna.
Använd inte elektriska skruvdragare för att
montera produkten. Den höga kraften i elektriska
verktyg kommer dra åt skruvarna för hårt vilket
kan skada gängorna.
Spänn inte skruvar eller muttrar för hårt. Dra åt
alla skruvar efter att hela möbeln monterats.
Stå eller sitt inte på bordet.
För att förlänga livslängden på möbeln, undvik
att låta den stå i regn. Under vintertid
rekommenderar vi att möbeln förvaras inomhus,
i torr miljö.
DONT’S

Component Hardware
A
Back frame 2 pcs
1
Bolt M6x40mm 24 pcs
B
Seat frame 3 pcs
2
Bolt M6x35mm 62 pcs
C
Side frame 2 pcs
3
Bolt M6x25mm 40 pcs
D
Connective back frame 1 pc
4
Bolt M6x20mm 20 pcs
E
Right frame 1 pc
5
Gaslift 2 pcs
F
Right back frame 1 pc
6
Connecting part 8 pcs
G
Right seat frame 1 pc
7
Plastic washer M8x10mm 4 pcs
H
Right front frame
1 pc
8
Allen key 1 pc
I
Left frame 1 pc
9
Leg soles 28 pcs

Component Hardware
J
Left back frame 1pc
10
Seat cushion 5 pcs
K
Left seat frame 1 pc
11
Back pillow 5 pcs
L
Left front frame 1 pc
12
Small back pillow 2 pcs
M
Table 1 pc
13
Table glass 1 pc
N
Ottoman 1 pc
14
Connecting part 2 pcs
Connecting frame 4 pcs
15
Cover fabric 1 pc
P
Connecting frame 4 pcs
16
Screw 16 pcs
Q
Connecting frame 2 pcs
17
R
Connecting frame 2 pcs
18
Glass 1 pc
Rain cove 2 pcs
S

Component Hardware
T
Connecting frame 8 pcs
X
Front frame 3 pcs
U
3 pcs
V
Bottom frame 3 pcs
Left side frame
Y
Right side frame 3 pcs

STEP 1 ( Single sofa : 2 pcs)
Connect Back frame (A) & Seat frame (B)
with Bolt (1)
B
A
Y
1
1
2
2
2
X
U
2
2
2
STEP 2
Connect part from STEP 1 & Right side frame (Y)
with Bolt (2)
STEP 3
Connect part from STEP 2 & Front frame (X)
STEP 4
Connect part from STEP 3 & Left side frame (U)
with Bolt (2)

17
V
1
1
1
11
1
3
9
3
STEP 5
Connect part from STEP 4 & Rain cover (17)
STEP 6
Connect part from STEP 5 & Bottom frame (V)
with Bolt (1)
STEP 7
Connect part from STEP 6 & Leg soles (9)
with Bolt (3)

STEP 8 ( Single Connective sofa : 1 pc)
Connect Connective back frame (D) & Seat frame (B)
with Bolt (1)
B
D
Y
1
1
2
2
2
X
U
2
2
2
STEP 9
Connect part from STEP 8 & Right side frame (Y)
with Bolt (2)
STEP 10
Connect part from STEP 9 & Front frame (X)
STEP 11
Connect part from STEP 10 & Left side frame (U)
with Bolt (2)

17
V
1
1
1
11
1
STEP 12
Connect part from STEP 11 & Rain cover (17)
STEP 13
Connect part from STEP 12 & Bottom frame (V)
with Bolt (1)
In this STEP, don’t assembly the Leg soles (9)

STEP 14 STEP 15
Connect Right Back Frame (F) & Right Seat
Frame (G) with Bolt (2)
Connect part from STEP 14 & Right Frame (E)
with Bolt (2)
STEP 16 STEP 17
Connect part from STEP 15 & Side Frame (C)
with Bolt (2)
Connect part from STEP 16 & Right Front
Frame (H) with Bolt (2)
2
22
22
G
F
E
CH
2
222
2
22

STEP 18
STEP 19
Connect Left Back Frame (J) & Left Seat Frame (K)
with Bolt (2)
Connect part from STEP 18 & Left Frame (I)
with Bolt (2)
J
K
I
2
2
2
22
STEP 20
Connect part from STEP 19 & Side Frame (C)
with Bolt (2)
C
2
2
2

STEP 21
Connect part from STEP 20 & Left Front Frame (L)
with Bolt (2)
L
22
2
2
4
6
STEP 22
Connect part from STEPS 13, 17, 21 with Connecting part (6) & Bolt (4)

STEP 24
Connect part from STEP 23 & Leg soles (9) with Bolt (3)
STEP 23
Connect part from STEPS 22 & Leg soles (9) with Connecting part (6) & Bolt (2)
2
2
2
2
9
9
6
3
9
3
at this STEP don’t assemble washer on Bolt (2)

T
Q
T
16
4
4
STEP 26
Connect 8 pcs Connecting Frame (T) &, 4 pc Connecting Frame (Q) with Screw (16)
STEP 25
Connect part from STEP 24 & Connecting part (14) with Bolt (4)

15
S
P
P
R
S
P
P
R
P
R S
16
on STEP 26
STEP 27
Connect part from STEP 26 & Fabric (15) by inserting frames into holes on fabric
STEP 28
Connect part from STEPS 27 & Connecting frame (P), (R),(S) with Screw (16)

7
5
72
2
STEP 29
Connect part from STEPS 25, 28 with Bolt (4)
STEP 30
Connect part from STEP 29 & Gaslift (5), Plastic washer (7) & Bolt (2)
4

STEP 31 STEP 32
Connect Table (M) & Leg soles (9) with Bolt (3) Put on Table Glass (13) to complete table
STEP 33
Connect Ottoman (N) & Leg soles (9) with Bolt (3)
13
M
3
9
3
N
3
9
3
STEP 34
Put on Table Glass (18) to complete ottoman
18

STEP 35
Put on Seat cushion (10), Back pillow (11) & Small back pillow (12) to complete sofa
10
11
12