Lyfco Kivik 166-1-58 User manual

ASSEMBLY MANUAL
BRUKSANVISNING
MODEL NAME: Kivik
KivikMODELLNAMN:
SKU: 166-1-58
Konsumentkontakt
Arc E-commerce AB
Box 3124
13603 Haninge
XX-YYWW
Please don’t remove the batch code sticker at back side of this product!
Any feedback please take picture of this batch code for traceablity purpose
NOTE: 50% TIGHTEN BEFORE FIXING ALL BOLTS
VIKTIGT – LÄS MONTERINGSANVISNINGARNA NOGA INNAN DU BÖRJAR
Ta inte bort ettiketten med batchnummer som finns på möbeln. Om du behöver hjälp med service eller reklamation av din möbel –
ange möblensbatchnummer till återförsäljaren, så att du kan få rätt reservdelar till just din möbel.

Attention! Please note that at rst all screws should be inserted slightly by hand!
Turn 2-3 times so that the screw grips on its own and connects all elements loosely. The screws
must only be driven in tightly when all elements are connected with each other in this way.
Otherwise the setup won´t be possible. Only by driving them in tightly afterwards, small
deviations of the borehole or the welded joints, which always occur with handcrafted products,
can be compensated.
Notes on an optimized assembly:
Before you completely tighten the screws, check carefully all the screws and tighten them
(only) to the extent that the product remains (especially chairs or loungers) still under load. If
you are sure that your product can withstand load, place it on a solid, level ground and put
some weight on it, please carefully and always with cushions. The various components can then
align with each other. Then tighten completely the screws. Thus you achieve and optimal
alignment of the product and prevent wobbling. Don’t sit, nd some weight.
Your new product was made by hand.
Slightly irregularities are rather seen as a
quality attribute than as a reason for
complaints.
Tip: Always fully insert the hex key inside
designated notch of screw.
If you don´t do that and slip out of the
screw, the screw will suffer damage and it
can caused the screw head to become
round inside you won´t be able to nd grip
with the hex key anymore!
VIKTIGHT
Don´t use this product if parts are missing, damaged or
worn down.
Don´t use any electronic tools to set up these product.
The high energy of these electronic tools will cause
screw overghten and therefor they won’t grid.
Don´t overghten screws or bolts. Only ghten the
screws enrely aer the product is completely set up.
You shouldn’t sit or stand on it.
Don´t let your product stand in the rain. Protect it from
weather impacts. In mes of freeze and over the
winter, we suggest you to store the product in a
covered dry place.
Var uppmärksam! Sätt först i samtliga skruvar löst. Dra inte åt, för då nns risk att skruvhålen inte
passar.
Innan du drar åt skruvarna helt, gör såhär för bästa resultat:
Ställ möbeln på en helt slät yta och lägg ett tillräckligt tungt föremål (ca 10-15kg) på den, så att
alla ben nuddar marken. Skruva därefter i skruvarna helt. Obs – använd inte din kroppstyngd, då
det är för mycket vikt. Om du följer dessa råd, blir din möbel stabil.
Om du inte följer dessa instruktioner kommer möbeln att bli ostadig och ”vickig” då produkten
upplevs ojämn.
Din nya möbel är handgjord. Små avvikelser
kan därför förekomma och är ett
kvalitetsattribut snarare än ett fel.
Tips: Var noga att alltid sätta in insexnyckeln
helt ner i skuven.
Om du inte gör det nns risk att insexnyckeln
slinter, vilket skadar skruven.
Skruvenkandåbliobrukbar.
Använd inte den här produkten om delar saknas,
är skadade eller utslitna.
Använd inte elektriska skruvdragare för att
montera produkten. Den höga kraften i elektriska
verktyg kommer dra åt skruvarna för hårt vilket
kan skada gängorna.
Spänn inte skruvar eller muttrar för hårt. Dra åt
alla skruvar efter att hela möbeln monterats.
Stå eller sitt inte på bordet.
För att förlänga livslängden på möbeln, undvik
att låta den stå i regn. Under vintertid
rekommenderar vi att möbeln förvaras inomhus,
i torr miljö.
DONT’S

Back Frame A
2
3
4
5
6
1
Seat Frame B
Front Frame C
Side Frame D
Back Frame E
Seat Frame F
E
F
Bolt M6x40mm
Bolt M6x35mm
Bolt M6x30mm
Bolt M6x60mm
Component Hardware
1 pc
1 pc
2 pcs
1 pc
2 pcs
1 pc
12 pcs
40 pcs
30 pcs
28 pcs
B
C
D
A
Nut M6
Bolt M6x20mm
7 pcs
7 pcs

8
9
12
7
Front Frame
Component Hardware
Back Pillow
Table Glass
Round Table Glass
Allen key
1 pc
2 pcs
3 pcs
1 pc
6 pcs
10
Pillow
G
K
Table Top Frame
Side Table Frame
Behind Table Frame
Front Table Frame
Round Table
L
I
J
H
1 pc
2 pcs
4 pcs
2 pc
2 pcs
Back Frame
A1
1 pc
Seat Cushion 6 pcs
Connecting part 6 pcs
11
13
14
1 pc
Spanner
1 pc

1 pc
Back Frame
Seat Frame
Front Frame
Front Frame
Side Frame
Side Frame
G1
D1
D2
C2
C1
E2
Component
B2
A2
E1
B1
Back Frame
Front Frame
Back Frame
Seat Frame
Front Frame
G2
M1
N1
Bottom Frame
Bottom Frame
1 pc
1 pc
2 pcs
1 pc
1 pc
1 pc
2 pcs
1 pc
1 pc
1 pc
1 pc
1 pc
M
Bottom Frame
N
Bottom Frame 1 pc
1 pc
Component
O
Rain Cover
O1
Rain Cover
1 pc
1 pc
B3
Seat Frame 1 pc

STEP 1
Connect Back Frame A (A) & Seat Frame B (B) with Bolt (1)
Connect part from STEP 1 & Side Frame D (D) with Bolt (3)
STEP 2
3
D
33
1
1
A
B
1
3

STEP 3
Connect part from STEP 2 & Front Frame C (C) with Bolt (3)
C
3
3
3
STEP 4
Connect back Frame E (E) & Seat Frame F (F) with Bolt (1)
F
E
1
1
1

STEP 5
Connect part from STEP 4 & Side Frame D (D) with Bolt (3)
STEP 6
Connet part from STEP 5 & Front Frame G (G) with Bolt (3)
D
3
3
3
G
3
3
3
3

4
12
4
STEP 7
Connect part from STEP 3 & STEP 6 with Bolt (1), Connecting part (12) & Bolt (4), (5) & Nut (6)
STEP 8
Put on Seat Cushion (11) & Back Pillow (7) to complete round sofa
1
6
5
11
7
7
11
1

STEP 9
Connect Back Frame (A1) & Seat Frame (B1) with Bolt (1)
STEP 10
1
1
1B1
A1
Connect part from STEP 9 & Side Frame (D1)
D1

STEP 11
STEP 12
Connect part from STEP 10 & Front Frame (C1) with Bolt (3)
3C1
1
1
1
F
E1
Connect Back Frame (E1) & Seat Frame (F) with Bolt (1)

STEP 13
STEP 14
Connet part from STEP 12 & Side Frame (D2) with Bolt (3)
3
3
3
3
D2
3
G1 3
3
Connect part from STEP 13 & Front Frame (G1) with Bolt (3)

STEP 15
STEP 16
Connect part from STEPS 14 & 11 with Bolt (1), (5) & Nut (6), (4) & Connecting part (12)
4
12
4
5
61
1
!
Connect part from STEP 15 & Rain Cover (O)
O
O

STEP 17
STEP 18
Connect part from STEP 16 & Bottom Frame (M) & (N) with Bolt (1), (5) & Nut (6)
N
1
1
1
1
5
1
6
6
5
1
1
1
M
11
7
7
11
Put on Seat Cushion (11) & Back Pillow (7) to complete bench round sofa

STEP 19
STEP 20
11
1
3
3
3
3
Connect Back Frame (E2) & Seat Frame (B3) with Bolt (1)
Connect part from STEP 19 & Side Frame (D2) with Bolt (3)
D2
E2
B3

STEP 21
STEP 22
Connect part from STEP 21 & Front Frame (G2) with Bolt (3)
G2
3
3
3
Connect Back Frame (A2) & Seat Frame (B2) with Bolt (1)
A2
11
1
B2

STEP 23
STEP 24
Connect part from STEP 22 & Side Frame (D1)
D1
Connect part from STEP 23 & Front Frame (C2) with Botl (3)
C2
3

4
12
4
STEP 25
STEP 26
Connect part from STEPS 21 & 24 with Bolt (1), (4) & Connecting Part (12), (5) & Nut (6)
1
6
1
5
!
O1
Connect part from STEP 15 & Rain Cover (O1)
O1

Connect part from STEP 26 & Bottom Frame (M1), (N1) with Bolt (1), (5) & Nut (6)
STEP 27
STEP 28
11
7
7
11
Put on Seat Cushion (11) & Back Pillow (7) to complete bench round sofa
M1 5
1
115
6
1
6
N1
1
1
1
1

STEP 29
Connect Table Top Frame (I) & Behind Table
Frame (K) with Bolt (2)
STEP 30
Connect part from STEP 29 & Table Side Frame (J)
with Bolt (2)
STEP 31
Connect part from STEP 30 & Front Table
Frame (L) with Bolt (2)
STEP 32
Put on Table Glass (8) to complete the table
2
2
I
KJ
J
8
2
2
22
2
2
2
2
2
2
2
L