Lynx BS Series User manual

USER MANUAL
Lynx Pro Audio S.L.
Valencia, Spain - www.lynxproaudio.com - [email protected]
BS series
BS-8
Bs-10
BS-12
BS-15
BS-112
BS-118
V.21.04

Manufacturer
CE CERTIFICACTION, EUROPEAN PRODUCT
BS-8
LYNX Pro Audio S.L.
Calle 1 - Pol. Ind. Picassent
E-46220 Picassent (Valencia)
This user guide is property of Lynx Pro Audio S.L. Any reproduction of this manual, by any means is strictly prohibited.
Copyright 2020. All rights reserved.
BS-10 BS-12
BS-15 BS-112 BS-118

BS Series User Manual
Lynx Pro Audio S.L 3www.lynxproaudio.com
INTRODUCTION
To facilitate the correct and reliable use of the BS cabinets we have designed this instruction manual, please read it
before proceeding to install the cabinet.
Please observe the technical data carefully and do not ignore the instructions included within this manual.
The BS series has been designed to offer an affordable yet reliable series of cabinets which not only deliver high
performance but have a sleek & attractive design and nish so that they not only sound great but also look impressive
in any install.
The series comprises four full range cabinets, all designed for a wide range of applications from xed installations,
nightclubs & bars, houses of worship, corporate events, as front ll and as stage monitoring. This four two-way, passive
full range cabinets include a single 8”, 10”, 12” and 15” with the series offering a tremendous sound and clarity over
short/mid distances.
The series is complemented by two passive subwoofer cabinets in 12” and 18” designed to extend low frequency
support to the four BS series full range units.
CONTENTS
• SAFETY PRECAUTIONS 4
• SYSTEM OVERVIEW
BS-8 5
BS-10 6
BS-12 7
BS-15 8
BS-112 9
BS-118 10
• CONNECTORS AND CONNECTIONS 11
• CABINET CONNECTIONS 13
• HARDWARE AND ACCESSORIES 14
• HOW TO USE ACCESSORIES FOR INSTALLATION 15
• RAINBOW 3D ACOUSTIC SIMULATION SOFTWARE 19
• CERTIFICATIONS AND GUARANTEE 20

BS Series User Manual
Lynx Pro Audio S.L 4www.lynxproaudio.com
Before starting to use this device, please read this instruction manual carefully.
Keep these instructions in the place where the equipment will be used and with easy access to them.
• Electrical appliance
The exclamation mark within a triangle identies the presence of electricity. Use the system carefully without wet
hands or feet. Avoid installing the speaker in wet or excesivelly humid places. Do not place material that contains
liquid on or near the unit. Avoid dripping or splashing water or any liquid over the unit. Regularly check the condition
of the cables and make sure these are not being walked on or pinched. Connect the speaker to bipolar, earthed
mains. The mains plug must be connected to the appropriate protection (fuse or breaker). Connection to any other
type of mains could result in an electrical shock and violate local electrical codes.
CAUTION: DO NOT CONNECT OR DISCONNECT THE AC POWER CONNECTORS UNDER LOAD.
•Heavy equipment
Apply back protection when using the system. Avoid loading and unloading at heights.
•Electrical shock risk
The diagonal mark within a triangle identies the presence of dangerous voltage.
Do not open or handle the interior of the box. These parts are not to be adjusted by the user. For maintenance and/
or repair please go to an authorized service centre.In order to reduce the risk of electric shock, disconnect from
AC before plug in or unplugging Audio signal cables. Reconnect to AC only if all signal connections are made and
secured. Never manipulate the ground type plug provided.
The AC mains plugs should always remain accessible for operation.
Unplug the loudspeaker during storms or when it’s being used for a long time.
•Hearing damage risk
These systems can reproduce large quantities of sound pressure which can damage hearing. Take precautions if
you are going to be near them for extended amounts of time and do not get too close.
•Hanging / Flying
Do not hang the cabinets from the handles or from any other part other than the designated hanging point. When
ying this system please observe the technical and “Rainbow” software data carefully. Never exceed the maximum
safe working loads or ignore the instructions included within this manual. Use Only ying accessories provided by
Lynx Pro Audio S.L. Rigging must be always carried out by professionals.
•Delicate Material
Please ensure no foreign object or water enters the speaker. Only clean the unit with dry cloths. Do not use solvents.
•Overheating / Fire risk
To reduce the risk of the speaker over heating, avoid direct contact with sunlight. Avoid placing the unit close to heat
inducing objects such as radiators. Do not cover the equipment in use and do not block any ventilation openings.
Do not put naked ame, such as lighted candles, close or on top of the unit.
•Electromagnetic and interferente emissions
Avoid placing objects which through electromagnetic waves can damage the unit, such as mobile phones, lap tops,
magnetic strip cards etc.
This system complies with normatives EN 55103-1 (1)
EN 55103-2 (2)
(1) This device may not cause harmful interferences.
(2) This device may receive interference including interferences that may cause undesired working.
•IMPORTANT NOTE
This Equipment must be used in accordance with these instructions and by trained professional personnel only.
This equipment should not be used in places with extreme tropical climates. Don’t expose this apparatus to extreme
humidity and or temperature values.

BS Series User Manual
Lynx Pro Audio S.L 5www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•HF 1” exit throat, (25 mm) voice coil, PETP dome compression driver
•LF 8” speaker, 2” ( 50 mm) copper wire voice coil, Waterproof cone with treatment
on both sides
Frequency range: 70 Hz – 18 KHz (-10dB)
Sensitivity: 93 dB
Max SPL / Peak: 118 dB/ 124 dB peak
Rated power: 300 W AES (600 W program, 1200 peak)
Dispersion: 90º x 60º rotatable
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4 Pin connections: +1 / -1 input +1 / -1 link
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 456 x 255 x 259 mm (H x W x D)
Weight: 12 Kg (26.4 lbs)
Fittings: 5 x M8, single pole-mount, ergonomic handle on the back position
Accessories: U bracket horizontal & vertical, M8 eyebolts, wall bracket, M20 pole
Enclosure type: Multiangle enclosure
•BS-8
Compact two-way cabinet. Consists of an 8” (2” voice coil) LF transducer and a 1” HF driver mounted on
a 90ºx60º rotatable horn.
• BS-8 measurements

BS Series User Manual
Lynx Pro Audio S.L 6www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•HF 1” exit throat, (25 mm) voice coil, PETP dome compression driver
•LF 10” speaker, 2” ( 50 mm) copper wire voice coil, Waterproof cone with
treatment on both sides
Frequency range: 65 Hz – 18 KHz (-10dB)
Sensitivity: 94 dB
Max SPL / Peak: 119 dB/ 125 dB peak
Rated power: 300 W AES (600 W program, 1200 peak)
Dispersion: 90º x 60º rotatable
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4 Pin connections: +1 / -1 input +1 / -1 link
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 500 x 300 x 301 mm (H x W x D)
Weight: 14 Kg (30.8 lbs)
Fittings: 5 x M8, single pole-mount, ergonomic handle on the back position
Accessories: U bracket horizontal & vertical, M8 eyebolts, wall bracket, M20 pole
Enclosure type: Multiangle enclosure
•BS-10
Compact, two-way passive cabinet. Consists of a 10” (2” voice coil) LF transducer and a 1” HF driver
mounted on a 90º x 60º rotatable horn.
• BS-10 measurements

BS Series User Manual
Lynx Pro Audio S.L 7www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•HF 1” exit throat, (25,4 mm) voice coil, annular diaphgram driver
•LF 12” speaker, 3” ( 75 mm) copper wire voice coil, Waterproof cone with
treatment on both sides
Frequency range: 60 Hz – 20 KHz (-10dB)
Sensitivity: 96 dB
Max SPL / Peak: 122 dB/ 128 dB peak
Rated power: 400 W AES (800 W program, 1600 peak)
Dispersion: 90º x 60º rotatable
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 589 x 350 x 348 mm (H x W x D)
Weight: 19 Kg (41.8 lbs)
Fittings: 5 x M8, double pole-mount with 10º angle, ergonomic handle on the back position
Accessories: U bracket horizontal & vertical, M8 eyebolts, wall bracket, M20 pole
Enclosure type: Multiangle enclosure
•BS-12
Compact, two-way passive cabinet. Consists of a 12” (3” voice coil) LF transducer and a 1” HF driver
mounted on a 90º x 60º rotatable horn.
• BS-12 measurements

BS Series User Manual
Lynx Pro Audio S.L 8www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•HF 1” exit throat, (25,4 mm) voice coil, annular diaphgram driver
•LF 15” speaker, 3” ( 75 mm) copper wire voice coil, Waterproof cone
with treatment on both sides
Frequency range: 55 Hz – 20 KHz (-10dB)
Sensitivity: 98 dB
Max SPL / Peak: 124 dB/ 130 dB peak
Rated power: 400 W AES (800 W program, 1600 peak)
Dispersion: 90º x 60º rotatable
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 664 x 425 x 420 mm (H x W x D)
Weight: 24 Kg (52.9 lbs)
Fittings: 5 x M8, double pole-mount with 10º angle, ergonomic handle on the back position
Accessories: U bracket horizontal & vertical, M8 eyebolts, wall bracket, M20 pole
Enclosure type: Multiangle enclosure
•BS-15
Compact, two-way passive cabinet. Consists of a 15” (3” voice coil) LF transducer and a 1” HF driver
mounted on a 90º x 60º rotatable horn.
• BS-15 measurements

BS Series User Manual
Lynx Pro Audio S.L 9www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•LF 12” speaker, 3” ( 75 mm) copper wire voice coil, Waterproof cone
with treatment on both sides
Frequency range: 40 Hz – 90 Hz with preset
Sensitivity: 93 dB
Max SPL / Peak: 120 dB/ 126 dB peak
Rated power: 500W AES (1000W program, 2000W peak)
Dispersion: Quasiomnidirectional
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 406 x 655 x 400 mm (H x W x D)
Weight: 29 Kg (63.9 lbs)
Fittings: 2 integrated ergonomic handles, 4 rubber feets right side for vertical install,
M-10 y points
Accessories: M-20 connector pole, M-10 eyebolt
Enclosure type: Multiangle enclosure
•BS-112
Compact, 12” (3” voice coil) passive subwoofer cabinet band pass conguration
• BS-112 measurements
655 400
400
406

BS Series User Manual
Lynx Pro Audio S.L 10www.lynxproaudio.com
SYSTEM OVERVIEW
• Technical Data:
Components:
•LF 18” speaker, 3” ( 75 mm) copper wire voice coil, Waterproof cone
with treatment on both sides
Frequency range: 38 Hz – 100 Hz with preset
Sensitivity: 98 dB
Max SPL / Peak: 126 dB/ 132 dB peak
Rated power: 600W AES (1200W program, 2400W peak)
Dispersion: Omnidirectional
Nominal Impedance: 8 Ω
Connectors: 2 X NEUTRIK Speakon NL4
Finish: Polyurea coating high grade resistant paint
Material: 15 mm Premium birch plywood
Dimensions: 533 x 660 x 570 mm (H x W x D)
Weight: 33 Kg (52.9 lbs)
Fittings: 2 integrated ergonomic handles, 4 rubber feets right side for vertical install,
M-10 y points
Accessories: M-20 connector pole, M-10 eyebolt
Enclosure type: Bass reex direct radiation subwoofer
•BS-118
Compact, 18” (3” voice coil) passive subwoofer cabinet band pass conguration
• BS-118 measurements

BS Series User Manual
Lynx Pro Audio S.L 11www.lynxproaudio.com
CONNECTORS AND CONNECTIONS
2.1 Normative
The BS cabinets meet the following standards:
EN 55032:2012 Electromagnetic compatibility of multimedia equipment. Emmision requeriments.
EN 55103-2:2009 Electromagnetic compatibility. Product family standard for audio, video, audiovisual
and entertainment lighting control apparatus for professional use. Part 2: Immunity.
EN 60065:2014 Audio, video and similar electronic apparatus. Safety requirements.
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products
with respect to the restriction of hazardous substances
BS cabinets are in conformity with the following EC directives:
Low Voltage Directive 2014/35/UE
Electromagnetic Compatibility EMC 2014/30/UE
RoHS Directive 2011/65/UE
RAEE (WEEE) 2012/19/UE
2.2 Connectors
The BS cabinets have a connection panel at the rear of the cabinet. This consists of 2 internally bridged Neutrik
NL4-MP connectors which apply no process to the signal.
Note: If pins +-2 are not used they will still be internally bridged.
The following table indicates which pins are used for all the models,
with passive and bi-amplied modes.
Cabinet Connector Speakon
connections
per box Impedance Rated power Program
power
BS-8 NL4 ± 1 input / link 2 8 ohms 300 W AES 600 W
BS-10 NL4 ± 1 input / link 2 8 ohms 300 W AES 600 W
BS-12 NL4 ± 1 input / link 2 8 ohms 400 W AES 800 W
BS-15 NL4 ± 1 input / link 2 8 ohms 400 W AES 800 W
BS-112 NL4 ± 1 input / link 2 8 ohms 500 W AES 1000 W
BS-118 NL4 ± 1 input / link 2 8 ohms 600 W AES 1200 W

BS Series User Manual
Lynx Pro Audio S.L 12www.lynxproaudio.com
CONNECTORS AND CONNECTIONS
To connect the speakon follow the instructions in g. 1
Insert the male speakon in its corresponding hole and turn right until it clicks. This xes it safely and strongly
and helps stop it being pulled out by mistake. At the other end of the cable connect in the same way to the
amplier channel.
2.3 Recommendations
Always ensure cables are in good condition. Know the recommended cable length and thickness according
to the cabinet and quantity you are installing. An incorrect connection can affect the functioning of the
system or even damage it. Cable thickness will vary according to cabinet impedance, quantity and distance.
This is especially important when connecting Subwoofers.
As a guide, please see the following table which outlines the thickness depending on the power and length
of cable.
Bear in mind Ohm ratings on the ampliers used to power the cabinets. For example, 2 ohm amplier
congurations are not recommended due to the excessive power from the amp output.
Never connect more cabinets than recommended in parallel. With parallel connections, the total impedance
can be calculated by dividing the impedance of 1 cabinet by the number connected.
Maximum recommended cable length for low impedance systems
Wire section AWG
number
Cable resistance in
100 meters
Maximum recommended lenght (in
pieces)
2 Ω 4 Ω 8 Ω 16 Ω
13.3 mm 6 0.25 ohm 24 57 122 253
6.63 mm 8 0.49 ohm 12 28 61 126
5.26 mm 10 0.62 ohm 10 23 48 100
3.31 mm 12 0.99 ohm 6 14 30 63
2.08 mm 14 1.57 ohm 49 19 40
1.31 mm 16 2.49 ohm 2 6 12 25
0.82 mm 18 3.98 ohm 2 48 16
0.52 mm 20 6.28 ohm 1 2 5 10
0.33 mm 22 9.89 ohm 1 1 3 6

BS Series User Manual
Lynx Pro Audio S.L 13www.lynxproaudio.com
• Mounting advice
The BS cabinets are designed to be used in all kind of xed installations.
Cabinets must be installed and suspended by professional installers.
Never place the safety of personnel at risk. Always check the accessories, slings etc are in good condition
and the suspension point is secure and free of excess weight, vibration, etc. Be careful where the cabinets
are suspended from.
All responsibility lies with the installation company.
• Coverage change with the rotatable horn
All the BS full range cabinets enable the horn to be rotated offering further coverage options. The rotatable
horn feature enables the installer to also set the cabinet up horizontally whilst maintaining the horn features
such as horizontal and vertical coverage. This is helpful in installs with low ceilings or where esthetically the
cabinet looks better horizontally.
The following BS cabinets have rotatable horns:
BS-8 (90ºx60º)
BS-10 (90ºx60º)
BS-12 (90ºx60º)
BS-15 (90ºx60º)
To turn on the horn the user must rst remove the cabinet grill, unscrew the horn, rotate it 90º and screw it
back in. Be sure to maintain the connection and put the grill back on.
CABINET INSTALLATION

BS Series User Manual
Lynx Pro Audio S.L 14www.lynxproaudio.com
HARDWARE AND ACCESSORIES
The BS cabinets are designed to be used in installations and the full range cabinets come with rigging points
so that they can be easily installed. To x the cabinets to a wall or to hold them from the ceiling is very easy
using some simple accessories:
UBR-BS8/10/12/15
U bracket for the BS-8, BS-10,
BS-12 and BS-15
AGR-8
M8 eyebolt for the BS-8,
BS-10, BS-12 and BS-15
SB-02
Lightweight aluminium stand
for the BS-8, BS-10, BS-12
and BS-15
TU-C02
M20 pole support for
combination between sub
and satellite cabinet
WB-20
Wall bracket for the BS-8,
BS-10, BS-12 and BS-15
AGR-10
M10 eyebolt for the BS-112
and BS-118

BS Series User Manual
Lynx Pro Audio S.L 15www.lynxproaudio.com
HOW TO USE ACCESSORIES FOR INSTALLATION
•UBR (U bracket):
UBR is the horizontal mounting system specially designed for Lynx Pro Audio cabinets. It is composed by the U
type support made of steel and 4 special xing screws (2 per side) in order to x the cabinet to the U support.
Back of the cabinet Cabinet front grill
• How to use it?
Before starting with the installation please note that the UBR bracket offers three different options and you
have to select one of them before installing the support. Simply check the following drawings and select the
best option in order to achieve the coverage required.
The angles show the different variations available (from A to B) in order to x the center of the cabinet (front
grill). Please pay special attention to the optimal positioning of your cabinet.
Position 3Position 1 Position 2
A
A
B
B

BS Series User Manual
Lynx Pro Audio S.L 16www.lynxproaudio.com
HOW TO USE ACCESSORIES FOR INSTALLATION
Once your selection is made (Position 1, 2 or 3) then you can start with the installation.
The rst thing to do is to x the UBR support in the place required (ceiling, wall, oor, etc).
Always check the suspension point is secure and free of excess
weight, vibration, etc. And be careful where the cabinets are
suspended from.
Before xing it completely please check that the position of
the bracket is correct. Remember where the front side is. If
everything is correct then you can x the UBR support (without
the cabinet).
It is very important to ensure that the support is strongly xed.
Please always check it. Never place the safety of personnel
at risk.
Once the UBR support is ready then you have to prepare the cabinet. You need to make some changes in
order to hook the enclosure from the U type bracket. See below.
Please have a look at the top and bottom of your cabinet. You will nd 2 screws in the middle of the top and
another two screws in the middle of the bottom. Just remove these shorts screws. You will use these holes
to x the cabinet to the UBR support, using the longer screws provided with the support kit.
If your Lynx Pro Audio cabinet is equipped with a pole mount support then just remove 2 screws of the pole
mount support (only 2) and use these holes to x the UBR support.
Cabinet
front Grill
Cabinet
front Grill
Now you have 2 holes available per side (top and bottom) without removing the pole mount support. And
you can use the holes available to x the cabinet to the UBR support.
Only use the special screws provided with the support kit.

BS Series User Manual
Lynx Pro Audio S.L 17www.lynxproaudio.com
HOW TO USE ACCESSORIES FOR INSTALLATION
Now that everything is clear we can start with the instalacion of the cabinet. We recommend the use of the
Position 1 or Position 2, and this is how to proceed:
If you choose Position 1 or Position 2 you will have to insert two special xing screws into the cabinet (one
per side) before installing the enclosure.
So rstly, take 2 of the xing screws provided and insert them into your cabinet. Where? Have a look. Seeing
the cabinet in horizontal position simply insert one xing screw in the UPPER HOLE of each side (left/right),
but don’t insert it completly. Just keep 5 mm out of the insert. These screws will help you to hook up the
cabinet from the UBR support in order to start with the cabinet installation.
Once the 2 screws are inserted (keeping 5 mm free) into the enclosure (one per side) then you can hook up
the cabinet (from the 5 mm free screws) into the UBR support. See the point H1 in the drawing of your choice
(Position 1 or 2). Just hook the cabinet placing the screws into the points H1 at both sides of the bracket. Do
not x them completely at the moment. You will do it when the cabinet is in the desired position.
Now you have to use the appropriate curve groove of the UBR support in order to slide the other xing
screw per side and orientate the cabinet. See the curve C2 in the drawing of your choice (Position 1 or 2).
Just insert the special screw in the appropriate curve and match the thread insert of the cabinet. You must
do it on both sides of the cabinet. Do not x them completely at the moment just keep 5 mm free so you can
guide the enclosure carefully to achieve the correct coverage.
When the cabinet is in the desired position then tighten the four screws (2 per side) and the cabinet will be
correctly installed.
C2
H1
B
A
Position 1
H1
C2
AB
Position 2

BS Series User Manual
Lynx Pro Audio S.L 18www.lynxproaudio.com
HOW TO USE ACCESSORIES FOR INSTALLATION
This is how to proceed in order to install the UBR in Position 3:
First, you need to have the 4 special xing screws in your hand/pocket (none in the enclosure). Seeing the
cabinet in horizontal position you will use the UPPER HOLE of each side (left/right) to insert one special
screw per side, but you won’t insert them now.
Before inserting the screws you have to hold the cabinet into the UBR bracket and match the UBR hole (see
drawing point 1) with the thread insert of your cabinet. Once hole 1 and the thread insert match then you
can insert the special screw (one per side). Don’t x the screw now, just keep 5 mm out of the insert.
Now you have to use the appropriate curve groove of the UBR support in order to slide the other xing screw
per side and orientate the cabinet. See the curve C2 in the drawing. Just insert the special screw in this curve
and match the thread insert of the cabinet. Do it on both sides. Do not x them completely at the moment
just keep 5 mm free so you can guide the enclosure carefully to achieve the correct coverage.
When the cabinet is in the desired position then tighten the four screws (2 per side) and the cabinet will be
correctly installed.
B
A
C2
H1
Position 3

BS Series User Manual
Lynx Pro Audio S.L 19www.lynxproaudio.com
RAINBOW 3D Acoustic Prediction Software
Lynx Pro Audio’s R&D department is working on Rainbow 3D, a new acoustic simulation software with dynamic
3D features. With a sophisticated design, Rainbow 3D stands out for its speed, being able to provide a simulation
in just a few seconds. It also provides algorithms for beam steering and optimizing the listening area.
• Designed from scratch by professionals
Rainbow 3D has been programmed from scratch by Lynx Pro Audio engineers, using new programming procedures
that achieve an effective simulation with really low calculation time.
• Multiple listening zones
The program can simulate all Lynx Pro Audio’s acoustic enclosures located in a 3D space, including the classic
side, top and front views. It can also dene multiple listening zones and allows offset positioning and symmetry.
Blueprint images, textures and PNG format pictures can be imported.
• Unlimited sound sources
Allows the acoustic simulation for an unlimited number of sound sources and audio systems. You can place as
many systems (subwoofers, line arrays, columns and individual boxes) as you desire. Also, the line arrays can be
placed in stack or own conguration.
• Beam steering
Rainbow 3D has the ability to add DSP processing to the simulation and uses algorithms to control the directivity
(beam steering) in columns, without the need to tilt them physically, being able to divide the column into several
beams that point to different zones.
• Accurate optimization thanks to FIR lters
Optimized algorithms are used in the listening area to improve the sound coverage and the frequency response. This
feature can be executed in a matter of seconds. Additionally, the export of FIR coefcients can be performed with
the optimization for later loading in the DSP via Ethernet or a USB device. In the near future direct communication
with Lynx Pro Audio and OCS will be available.
• Multiple measures and tools
Likewise, the R&D department is developing multiple measurement and analysis tools for the calculated data. For
example, the sound pressure curves (SPL) in the listening areas and the capture of virtual measurements that show
the frequency response in the points of location indicated and added. Among other tools you will nd autosplay
and a wizard to set up different subwoofer arragements.

BS Series User Manual
Lynx Pro Audio S.L 20www.lynxproaudio.com
DECLARATION OF CONFORMITY
Lynx Pro Audio S.L.
Calle 1 - Pol. Ind. Picassent
46220 Picassent (Valencia)
SPAIN - EU
Tel.: [phone]
www.lynxproaudio.com
Lynx Pro Audio S.L. declares that ionic series are in conformity with the following EC directives:
Low Voltage Directive 2006/95/EC
Electromagnetic Compatibility EMC 2004/108/EC
RoHS Directive 2002/95/EC
In accordance with Harmonized European Norms:
EN 60065:2002 Audio, video and similar electronic apparatus. Safety requirements
EN 55032:2012 Electromagnetic compatibility of multimedia equipment. Emission requeriments.
EN 55103-1:1996 Electromagnetic compatibility. Product family standard for audio, video,
audiovisual and entertainment lighting control apparatus for professional use.
Part 1: Emission.
EN 55103-2:1996 Electromagnetic compatibility. Product family standard for audio, video,
audiovisual and entertainment lighting control apparatus for professional use.
Part 2: Immunity.
BS models: BS-8 / BS-10 / BS-12 / BS-15 / BS-112 / BS-118