Lynx yellobrik OTR 1210 User manual

We are constantly adding more yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com
OTR 1210 (MM)
MADI / Fiber Optic Transceiver
12V 0V
⎓
Power
WARNING
CLASS 1
Laser Product
TX
RX
MADI / Fiber Optic
Transceiver
MADI
10km
IN OUT
LYNXTechnik AG
WARNING
CLASS 1M LASER PRODUCT
LASER RADIATION
Do not view directly with
optical instruments
Coaxial MADI Input
Coaxial MADI OutputDC Power Input
Technical Specications
Coax Input 1 x 75 Ohm BNC connector
Supported standards: AES10-2008
Cable length 250m ( Belden 1694A )
Coax Output 1 x 75 Ohm BNC connector
Amplitude: 750mV P/P
Cable length 250m ( Belden 1694A )
Fiber Optic 1 x ber optic input (LC/PC Connections)
1 x ber optic output (LC/PC Connections)
Singlemode Version: OTR 1210
Transmitter: 1310nm ( -9 to dBm -3dBm )
Receiver sensitivity: 1260nm to 1620nm ( -23dBm )
Max. Distance 10km ( 6.2 miles )
Multimode Version: OTR 1210 MM-850
Transmitter: 850nm ( -2dBm to -7dBm )
Receiver sensitivity: 850nm ( -15dBm )
Multimode Version: OTR 1210 MM-1310
Transmitter: 1310nm ( -14dBm to -20dBm )
Receiver sensitivity: 1310nm ( -30dBm )
Power +12V DC @ 2.2W nominal - (power supply included)
(supports 7 - 24V DC input range)
Power LED on side of module
Power
RX Data
Active
TX Data
Active Fiber Input/Output
The OTR 1210 has a singlemode 1310nm Duplex
LC connector SFP pre-installed.
The OTR 1210 MM has either a 1310nm or 850nm
Multimode Duplex LC connector SFP pre-installed,
depending on your requirements.
WARNING: Module laser is active as soon as power is
connected, regardless of LED indication
yellobrik
®
Quick
Reference
yellobrik
®
LYNX
Technik
AG
| Broadcast Television Equipment

Connections
The coax MADI in- and outputs are connected to the corresponding 75
Ohm BNC connections provided. The ber connection is made to the LC
connector as indicated on the module. An example of a LC connector
shown below.
Note: The module is designed for use with SMF
(Singlemode) ber cable.
Use the included dust plug to protect the optical connection from dust.
Operation
The OTR 1210 exclusively supports transmission of MADI signals
according to AES10-2008. It is used to convert coaxial MADI signals (up to
64 channels IN and OUT) into ber for use in long distance applications.
The electrical / optical conversion introduces no delay (zero latency) and
there is no signal degradation.
Operation if fully automatic. There are no user adjustments for the
module. The module supports hot swapping and hot plugging of all
connections.
Note: If TX LED is OFF this indicates no SDI input is present, or the input signal
is not valid. If RX LED is OFF, then this indicates that no optical input signal is
connected or the optical input power is too low.
Power
The module requires a clean 12V DC (7-24V DC) power source. An LED
is provided to conrm power is connected. A 12V DC power supply is
included with the module. If you are applying your own power source,
please provide a clean, 7-24V DC power source. Power consumption
information can be found in the technical specications table.
Power Lead Strain Relief
The module has a small hole in the case which is located above the
power connection. This prevents the power lead being accidentally
pulled out. Use the supplied tie-wrap and secure the lead as shown
below.
Optional Mounting Solutions
The optional RFR 1001 mounting bracket can be
used to permanently mount the module on any
surface or on 19”rack rails.
The optional RFR 1000-1 rack mount can be used to permanently
mount up to 14 yellobrik modules. In addition, the RFR 1000-1 can
provide full power redundancy for all mounted yellobriks.
Note: The OTR 1210 is identical in terms of mounting and securing.