Lynx yellobrik OTR 1440 User manual
yellobrik Quick
Reference
OTR 1440
12Gbit Fiber Optic / SDI Transceiver (CWDM)
LC Fiber Optic
Input / Output
SDI Video
Output
Transmitting
Data
LYNXTechnik AG www.lynx-technik.com
DC Power Input
Power
Connected
WARNING
LASER RADIATION
Do not view directly with
optical instruments
CLASS 1M LASER PRODUCT
SDI Video
Input
Receiving
Data
Please visit the yellobrik website to see all the yellobriks
www.yellobrik.com
®
yellobrik
®
Technical Specifications
SDI Video 1 x SDI video input
1 x SDI Video output
75 Ohm BNC connectors
SMPTE 2082-1, SMPTE 2081-1, SMPTE 424M, SMPTE 292M
Multi-standard operation from 1.5bit/s to 12Gbit/s
Multi-rate reclocking
1.5Gbit/s - 3Gbit/s - 6Gbit/s - 12Gbit/s
Return Loss: > 15dB to 1.5GHz and > 10dB up to 3GHz
Automatic cable EQ
260m @ 1.5Gbit/s, 150m @ 3Gbit/s (Belden 1694A cable)
80m @ 12Gbit/s, 6Gbit/s (Belden 4794R cable)
Fiber Optic 1 x fiber optic input
1 x fiber optic output
(CWDM - 18 selectable wavelengths - ITU-T G.694.2), TX Power: -2..+3dBm
Duplex (Singlemode) using LC/PC Connections
SMPTE 297M - 2006
Hot pluggable
TX active LED, and RX active on side of module
Single mode transmit / receive (duplex connector)
Max. distance approx. 10km (6.2 miles) @ 12Gbit/s (Singlemode)
Power +12VDC @ 1.9W nominal without SFP
+12VDC @ 2.7W nominal with SFP
( supports 7 - 24VDC input range )
Brunnenweg 3, D-64331 Weiterstadt, Germany | Phone: +49 (0) 6150 1817 0
Connections
The SDI video input and output is connected to the corresponding 75
Ohm BNC connections provided (up to 12Gbit). The ber connections
are made to the LC connector as indicated on the module. The
connection is LC Duplex (single mode). An example of a single LC
connector shown below, one is required for the input and output
connection.
Operation
The OTR 1440 combines a CWDM ber optic transmitter and receiver
into a single package. Dierent video formats up to 12Gbit can be
transmitted and received. Operation of the receiver and transmitter is
automatic. For transmission, the Input video format is automatically
detected and the video signal is reclocked and then transmitted over the
ber optic connection. For reception, the received SDI format is
detected automatically and provided on the SDI output connection
The OTR 1440 supports any SDI video signal from 1.5Gbit/s to 12Gbit/s.
Max distance is 10 Km (6.2 miles). Data send and receive activity is
indicated by the LEDs located on the side of the module. The module
supports hot swapping and hot plugging of connections.
This is a CWDM module and there are 18 dierent wavelength selections
for the ber transceiver SFP. Wavelength selections are according to
ITU-T G 694.2.
Power
The module requires a 12V DC power input and the LED conrms when
power is connected. A power supply is provided, however if you use
your own power supply, please provide a clean power source between
7 and 24VDC.
Power Lead Strain Relief
The module has a small hole in the case which is located above the
power connection. This prevents the power lead from being accidental-
ly pulled out. Use the supplied tie-wrap and secure the lead, as shown
below.
Optional Mounting Bracket
The optional RFR 1001 mounting bracket can be used to permanently
mount the module on any at surface or on 19” rack rails.
The optional RFR 1000-1 rack mount can be used to mount up to 14
yellobrik modules permanently. In addition, the RFR 1000-1 can provide
full power redundancy for all mounted yellobriks.
Other Lynx Transceiver manuals
