Lyte HIPOD 1000 User manual

HIPODUSERGUIDE
SAFETY INFORMATION
IMPORTANT: Never use the HIPOD LLWP until you have fully read and understood the user guide and the HIPOD LLWP has
been correctly set up using the information it contains.
ALWAYS carry out a Risk Assessment for each task before you start work, to ensure the HIPOD LLWP is the appropriate mode
of access for the task that needs to be undertaken.
Maintenance checks before use:
HIPOD 1000, 1200 & 1500
Lyte Ladders & Towers
www.lyteladders.co.uk
Mobile One Person Low Level Work Platform (LLWP)
Maximum Safe Working Load 150 KG
Repairs:
EQUIPMENT CARE
3Check that the HIPOD LLWP structure is not bent bowed, twisted, dented, cracked or corroded.
3Check that the HIPOD LLWP structures around the xing points for other components are in good condition.
3Check that xings (usually welds rivets, screws or bolts) are good, appropriate, not missing, loose, or corroded.
3Check that components are not missing, loose, excessively worn, corroded or damaged.
3Check that the locking mechanisms are operating locking correctly. Gate hinges, springs, ladder hinge elbow
locking joints platform clips are not damaged.
3Check all caster wheel brakes operate.
3Check that the entire HIPOD LLWP is free from contaminants. (e.g. dirt, mud, paint, oil or grease)
3Check that the platform (if tted) has no missing parts or xings and is not damaged or corroded.
Note: If any of the above checks cannot be fully satised you should NOT use the HIPOD LLWP.
• Replacement parts are available and simple to replace. Contact your supplier.
• You should not attempt to repair the LLWP unless you are qualied/competent to do so.
• You can seek advice from the manufacturer regarding repair or replacement.
The important considerations when storing a LLWP (not in use) should include the following:
• Is the HIPOD LLWP stored away from areas where its condition could deteriorate more rapidly
(e.g. dampness, excessive heat, or exposed to the elements)?
• Is the HIPOD LLWP stored in a position which helps it to remain straight?
• Is the HIPOD LLWP stored where it cannot be damaged by vehicles, heavy objects, or contaminants?
• Is the HIPOD LLWP stored where it cannot cause a trip hazard or an obstruction?
• Is the HIPOD LLWP stored securely where it cannot be easily used for criminal purposes?
Storage:
HIPOD
Lyte_HiPod_Instruction_Leaflet.indd 1Lyte_HiPod_Instruction_Leaflet.indd 1 16/12/2013 11:10:5916/12/2013 11:10:59

Read the instructions
Do not use
Damaged Equipment
Only ascend or descend the LLWP
using the access provided
Never stand on the side protection
or use boxes, stepladders or other
objects to gain extra height
Inspect before use
Do not
overreach
Face the access when
ascending and descending
Never more than
one person
Never stand on the
access ladder to work
Working platform must be level
Do not use on loose
or slippery surfaces
Ensure all breaks are locked, where the LLWP
incorporates breaks e.g. Caster Wheels
Never move when a
person is standing
on a work platform
Never work near
power lines or other
electrical Equipment
Do not use on sloping or uneven surfaces,
where the LLWP is not tted with
a means of levelling the LLWP, such
as adjustable legs. Contact the
manufacturer for further information
Ensure side protection gate is
closed and secure before use
Never use as a means
of access to another place
Beware of nger traps
Ensure all
components
are present and
correctly tted
before use
7DON’TS...
DO’S AND DON’TS WHEN USING
A HIPOD WORK PLATFORM...
3DO’S...
When moving and positioning the HIPOD LLWP ensure caster wheel brakes are unlocked.
Open front and rear frames which will allow both side frames
with elbow joints to unfold.
Depress self return pin on the elbow joint then open fully.
Release self return pin locking frames in the open
position. Always check elbow joints are locked and
secure before proceeding.
Lower and pivot the access and egress ladder to the ground
by releasing the locking strap situated to the side of the
front frame.
Ensure ladder locking arm is engaged and secure in the
sprung catch before climbing the ladder.
Place the closed unit in the upright position,
unlock all casters.
Opening the HIPOD LLWP
Release locking brace that locks the front and
rear frames together.
When the HIPOD LLWP is square and in position, ensure that
the platform is xed to the chosen height.
Locate the platform claws on the front and rear frames,
ensure the claws are sitting on the horizontal tube.
Lock and secure the 4 platform clips to the front and rear
tubes when in the correct position.
Ensure the articulated feet are positioned on the
oor correctly.
1.
3.
5.
2.
4.
6.
1.
5.
5.
9.
1.
2.
6.
6.
10.
2.
3.
7.
7.
11.
3.
4.
8.
8.
4.
SETTING UP THE HIPOD LLWP
Lyte_HiPod_Instruction_Leaflet.indd 2-3Lyte_HiPod_Instruction_Leaflet.indd 2-3 16/12/2013 11:11:1216/12/2013 11:11:12

IMPORTANT: Never climb the HIPOD LLWP until you have checked the following:
• The ladder is secure and positioned correctly.
• The platform is secure and positioned correctly.
• All Casters / base plates are positioned correctly.
• All locks to folding gate and casters are applied.
Ensure all caster wheels are locked before use and pointing outwards.
Using the ladder section climb onto the platform of the workstation.
Push the sprung saloon gate when entering the platform.
The sprung saloon gate will self-close when on the work platform.
Ensure saloon gate has closed before any work.
www.lyteladders.co.uk
Tel: [phone]
Email: [e-mail]
7.
8.
Altering the platform height on the HIPOD LLWP:
1. Release locking clips from the front and rear tubes
2. Position platform at the lower level ensure claws are positioned over the front and rear tube
3. Lock platform retaining clips
HIPOD optional extra
Toeboard tting
1. Stand 1 x long toeboard section with link clamp facing down
and 1 x short toeboard section with link clam facing up
2. Slide long toeboard link clamp down onto upward facing link clamp
on short toeboard. Ensure two boards are rmly linked
3. Repeat step 1 and 2 until all 4 toeboard sections are in place
Caster, Base Plate, and Adjustable leg Fitting
1. Remove the leg tting by pulling rmly to discharge the spring tension
2. Replace the other leg tting by pushing the top into the empty podium leg depressing the captive spring.
The spring tting at the top will keep the legs retained in the tube in all normal usage and prevent the legs from falling out
HP 005 Instruction
Lyte_HiPod_Instruction_Leaflet.indd 4Lyte_HiPod_Instruction_Leaflet.indd 4 16/12/2013 11:11:2516/12/2013 11:11:25