Mac Faucets ASD-13 User manual

PAGE | 01
Installaon Instrucons
User Manual
Automac Liquid Soap Dispenser
Model: ASD-13
ASD-13
Soap Dispenser
Stainless Steel Construcon
Dispenses Standard Liquid Soap Only, commonly found in retail stores
1000ml Integral / Soap Bole
Vandal Key
Integral Baery Compartment
Mounng Hardware
Baeries Pre-installed (6 AA)
All hardware necessary for sasfactory installaon
Package Includes
866 558 3200 310 919 3073 [email protected] www.macfaucets.com
MAC FAUCETS California, USA
D
E
S
I
G
N
E
D
&
A
S
S
E
M
B
L
E
D
I
N
T
H
E
U
S
A
3-11/116”
10-13/16”
4”
01
05 07
Please cut for drilling holes
Drill Holes Ø 1/4”
Once the locaon for the Soap
dispenser has been decided,
proceed with the installaon
steps below, if the soap
dispenser is installed above the
sink, leave a space of 18” from
the top of the sink to the
boom of the soap dispenser as
shown below in figure (A).
1. Cut the template from the
back of the dispenser box.
2. Use a level to align the
template correctly.
3. Use painters tape to hold the
template in place.
4. Drill holes for supplied plasc
anchors.
03
04
02
Place the plasc anchors in the holes. Drive
them in with a lite hammer.
Align the holes of
the dispenser with
the holes of the
anchors. Insert
screws in and
fasten using a
Phillips screw
driver.
Insert the key into the hole
located at the top of the
dispenser, push down with the
key and pull the cover open.
The cover engages a power
cut-off switch located in the
dispenser. The dispenser will
not acvate when the cover is
in the open posion.
Tools Needed
Safety Glasses
Drill bit
Ø 1/4” Carbide
Drill for le
Cordless Drill
Hammer
Level
Phillips Screw Driver Tape
06
18”
Fig. A

PAGE | 02
866 558 3200 310 919 3073 [email protected] www.macfaucets.com
MAC FAUCETS California, USA
10
11 12
Remove the
cap from the
soap
container.
Fill the soap
container with
liquid soap.
DO NOT USE
GRIT TYPE
SOAPS.
Put back the
cap and close
the soap
container.
08
Remove the soap
container and
install the soap
dispenser in place,
fasten securely.
09
Put back
the soap
container,
making sure the
the pump is
inserted in the
yoke
13
14
02
03
15
01
Take the
baery case
out of the
compartment
Pull the tab
out of the
baery case,
and insert it
back in the
baery case
compartment
Tab
Pump
lnsert six (6)AA size alkaline
as shown in Baery
compartment figure 02.
Close the compartment
by sliding the tab unl it
clicks into in place.
Close the cover,
make sure the
cover is locked
and secured
against the back
plate.
Usage:
Replacing Baeries
01 Loading baeries and the LED will flash 3 mes
indicang the dispenser is ready for use.place hand(s)
underneath dispenser within 5" of the sensor,the
dispenser will dispense approximately 2ml of soap
(O.Bml foam soap) into your hand(s).
02
*Please pass the instrucon to the user aer finish install
Baery
compartment
open
Push the Baery
Case to close
Press this tab
to Open
Back Plate
Soap re-fill
Pump
Baery Case
Baery
Compartment
Cover
Power Switch
Yoke
Led Indicator
For reference See Replacement Baeries
Note:
1. The dispenser cover must be closed to acvate.
2. When the baeries are too low, the LED will blink
connuously. The dispenser will not work, change the
baeries inmmediately.