MacroAir Technologies WhisperFoil User manual

………………………Owners Manual ...
Installation Manual

Page 2
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Installation Manual Contents
Anatomy of a Fan --------------------------------------------------------------------------------------------------- 4
Check Your Shipment, What's Included For 10 & 6 Blade Fans--------------------------------------------------- 5
What You Need To Get Started ------------------------------------------------------------------------------------- 5
Check Your Shipment, What’s Included For eco6 Guard Fan --------------------------------------------------- 6
1 Important Information, PLEASE READ FIRST ---------------------------------------------------------------------------------- 7
1.1 Key Safety System Components-------------------------------------------------------------------------------- 7
1.2 Placement and Spacing ---------------------------------------------------------------------------------------- 7
1.3 Fan Clearance Drawing ---------------------------------------------------------------------------------------- 7
1.4 Mark Floor To Alert Personnel ----------------------------------------------------------------------------------- 7
1.5 Sprinkler Systems and Fan Placement-------------------------------------------------------------------------- 8
1.6 Locating Control Panels ----------------------------------------------------------------------------------------- 8
1.7 Connecting Fans to Remote Controls -------------------------------------------------------------------------- 8
1.8 Shielded Motor Cable ------------------------------------------------------------------------------------------- 8
1.9 Check Federal, State and Local Codes ----------------------------------------------------------------------- 8
2.0 General Mounting Considerations ----------------------------------------------------------------------------- 8
2.1 Weight ------------------------------------------------------------------------------------------------------------ 9
2.2 Torque ------------------------------------------------------------------------------------------------------------ 9
2.3 Safety Cable ----------------------------------------------------------------------------------------------------- 9
2.4 Close Clearances ----------------------------------------------------------------------------------------------- 9
2.5 Guy Cables ------------------------------------------------------------------------------------------------------ 9
2.6 Guards ----------------------------------------------------------------------------------------------------------- 9
2.7 Universal Mounting Hardware -------------------------------------------------------------------------------- 10
2.8 Maintenance -------------------------------------------------------------------------------------------------- 10
Control Panel ---------------------------------------------------------------------------------------------------------------------------- 10
Power Unit --------------------------------------------------------------------------------------------------------------------------------- 10
Mounting Hardware ------------------------------------------------------------------------------------------------------------------- 10
2 Installation Procedures ---------------------------------------------------------------------------------------------------- 11

Page 3
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Step 1, Install Mounting Hardware ------------------------------------------------------------------------------- 11
Step 2, Attach Power Unit To Mounting Hardware -------------------------------------------------------------- 12
Step 3, Attach Safety Cable -------------------------------------------------------------------------------------- 12
Step 4, Mount The Motor Control Panel -------------------------------------------------------------------------- 12
Step 5, Mount Remote Switchbox -------------------------------------------------------------------------------- 13
Step 6, Make Control Circuit Connections ---------------------------------------------------------------------- 13
Step 7, Make Motor Lead Connections -------------------------------------------------------------------------- 13
Step 8, Install Guy Wires ------------------------------------------------------------------------------------------- 15
Step 9, Install Fan Blades, Blade Safety Links, & Safety Link Extenders ---------------------------------------- 16
Step 10, Check Clearances And Guy Wire Tension For Safety ------------------------------------------------- 17
Step 11, Install Guards If Necessary ------------------------------------------------------------------------------ 18
Step 12, Install Input Power --------------------------------------------------------------------------------------- 18
Step 13, Verify Proper Operation --------------------------------------------------------------------------------- 18
3 Installation Procedures For eco6 Guard Fan ----------------------------------------------------------------------------- 20
Step 1, Install Mounting Assembly eco6-------------------------------------------------------------------------- 20
Step 2, Attach Motor Assembly To Mounting Assembly eco6 ------------------------------------------------- 21
Step 3, Make Control And Motor Cable Connections eco6 --------------------------------------------------- 21
Step 4, Attach Rear Safety Screen eco6------------------------------------------------------------------------- 22
Step 5, Attach Hub And Hub Cover eco6 ------------------------------------------------------------------------ 22
Step 6, Attach Fan Blades eco6---------------------------------------------------------------------------------- 23
Step 7, Attach Rear Safety Screen eco6 ------------------------------------------------------------------------- 23
Step 8, Make Final Adjustments And Attach Safety Cable eco6 ---------------------------------------------- 24
Regulatory Notice ------------------------------------------------------------------------------------------------------------ 25
EMI | Electromagnetic Interference --------------------------------------------------------------------------------------------------- 25
Multi Fan Wiring Diagram ---------------------------------------------------------------------------------------------------- 26
Mounting Dimensions Diagram --------------------------------------------------------------------------------------------- 27
Motor Control Panel and Assembly Drawing ------------------------------------------------------------------------------ 28
Contact Information --------------------------------------------------------------------------------------------------------- 29

Page 4
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Anatomy of a Fan

Page 5
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Check Your Shipment, What’s Included For 10 & 6 Blade Fans
Blade Carton (Blades)
Power Unit Carton
Remote Control Box (where applicable)
Motor Control Panel with Variable
Frequency Drive
(where applicable)
Owner’s Manual with Warranty Card
Installation Manual
Gearbox Vent Cap (For Dodge Only)
Power Unit
(all preassembled)
Hub
Frame
Gearbox
Motor with J-Box
Safety System
Universal Mounting Hardware
Swivel Mount Assembly
4 Guy Wire Cables 1/8 inch
Guy Wire Clamp Kit (includes tension
tool)
Safety Cable ¼ inch
Safety Cable Bolt Pack
Blade Bolt Pack
Mounting Hardware Pack
Blade Safety Links (boomerang-shaped)
Clamps
Shims
Safety Link Extensions
What You Need To Get Started
Scissor Lift
5/16 inch through ¾ inch wrench and socket set
Phillips and standard screw driver
Pair of ¾ inch wrench and sockets
Pair of ½ inch wrenches or wrench and sockets
5/16 inch sockets or wrench
Call MacroAir at 866.668.3247 if you have any questions
Blade Boxes
Power Unit Carton

Page 6
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Check Your Shipment, What’s Included For eco6Guard Fan
Motor Mount Assembly
Motor/gearbox attached to motor mount
If ordered without safety screens, the hub, hub cover, and
hub safety system will also be attached to this along with the
keyless bushing adapter.
Wall Mount Assembly
V-shaped (roughly) wall mount
Pivot mount (attached to wall mount)
If the fan is ordered with screens, the following will be in the
box.
Safety cable
Safety cable bolt kit
Blade bolt kit
Keyless bushing adapter
Bolts and washers to attach keyless bushing adapter to hub
Packet of bolts, nuts, and washers to attach rear screen to motor mount
Packet of large sheet metal screws to attach front screen to rear screen
Hub cover
Screws and star washers to attach hub cover
Hub (loose in the crate)
If the fan is ordered without screens, the
following will be in the box.
Safety cable
Safety cable bolt kit
Blade bolt kit
Blade safety links and safety link extenders
Variable speed models include a control panel, remote, remote wire, motor cable and cable glands
(same as regular fan). Single speed models will have an AG Starter and AG Starter enclosure with instruc-
tion manual and warranty card loose rather than in the MCP box.
All the above is in the power unit crate.
If the fan is ordered with screens, they will be on a separate pallet.
Blades will be on a separate pallet, although they can be theoretically included in the main power unit
crate.
Call MacroAir at 866.668.3247 if you have any questions
Eco6 Guard Fan

Page 7
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Please Read this Important Information Before you Install Fans
• Make sure Power is OFF before beginning any installation or maintenance procedure.
• Refer to the enclosed packing list and verify that all fan components are included before you begin.
1.1 Key Safety System Components
MacroAir fans are engineered with key safety features to prevent pieces of the fan from falling in the
unlikely event of a catastrophic failure. Used together, these systems and devices provide
comprehensive protection of people, equipment, and property. Follow the detailed instructions precisely
when installing fans, including the installation of the following:
Install safety cable and guy wires on every fan. Properly installed, the guy wires will keep the fan stable in
case of earthquake or, for “outdoor” installations where high wind conditions may occur. The safety
cable, if installed per MacroAir specifications, will prevent the fan from falling in the unlikely event the
mounting system should fail.
Install the complete set of blade safety links, which connect each blade to the adjacent blades, and the
safety link extensions, which reinforce the area between the mounting holes. This is an important
precautionary measure should a blade break off at the hub for any reason.
1.2 Placement and Spacing
Check the area where fans will be mounted to determine vertical and horizontal spatial clearances. A
standard ceiling fan is mounted so the measurement from the bottom of the beam to the bottom of a
fan’s hub is 3 feet. Extensions may be ordered to lower the fan if needed. Ceiling fans should be
mounted so the lowest part; the blades, are located at a minimum of 10 feet above the floor. If possible,
avoid mounting fans directly below lights or skylights to avoid any strobe effect caused by moving blades.
Note, a large fan, 20 – 24 feet in diameter, performs best at 20 to 30 feet above the floor, but acceptable
performance has been demonstrated as low as 10 feet and as high as 50 feet.
If the building has a mezzanine, fans should be mounted so a person can not reach a fan in any way from
the upper level/deck. Make certain fans are positioned so the blade tips are at least 3 feet away from
any area where a person may be able to extend outward to reach them.
1.3 Fan Clearance Drawing
Note, fans must be far enough below the ceiling to allow proper air circulation — no closer than 15% of
the fan diameter. Due to the design of our fans and mounting hardware, fan blades droop
approximately six inches below the bottom of the hub when the fan is at rest. If required, extension
mounts are available from the factory. For more information, refer to the “Fan Clearance” drawing, see
Figure 1 on page 8.
1.4 Mark Floor to Alert Personnel
When mounting a fan in an area where materials may be elevated into its path, MacroAir recommends
marking or painting the floor with a large crosshatched circle to alert personnel of the overhead location
of fans.

Page 8
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
1.5 Sprinkler Systems and Fan Placement
In any installation where fire sprinklers are in place, do not interfere with their correct operation. Note; fans
should be located not less than 3 feet below a sprinkler, and placed central to each sprinkler quadrant.
Our standard variable-speed control system can be connected to a fire suppression control system, which
will emergency-stop fans in case of fire. Prior to installing fans, review all codes applicable to sprinkler
systems and fans to ensure code compliance. Refer to the wiring diagrams packaged inside the control
panel for proper installation. If further advice is needed, you may contact our support staff. However, it is
your sole responsibility to see that the installation is completed to code and that it is correct.
1.6 Locating Control Panels
Each fan has its own motor control panel (MCP). A motor control panel must be mounted at least 5 feet
outside maximum blade length, and within 25 feet of the fan. Make sure the lockable service disconnect
located on the side of the MCP is within line of sight of the motor to comply with OSHA and local safety
codes.
1.7 Connecting Fans to Remote Controls
You may control one fan or many fans with a single remote control switch box. The remote switch box
should be located no more than 100 feet (supplied) from the motor control panel. Fans may also be
controled with temperature control sensors and building automation systems. Contact technical support
for more information.
1.8 Shielded Motor Cable (For Variable Frequency Drives)
To minimize electromagnetic interference and stray voltage, each MacroAir fan assembly includes 25 feet
of shielded motor cable, cable glands, and a variable frequency drive with a built-in filter. The shielded
motor cable connects the fan motor to the motor control panel. This system reduces the likelihood of
electronic-broadcasting and receiving which can interfere with radio and other sensitive equipment.
Plus, this system cuts fan installation cost as conduit is not needed where shielded cable is used. For more
regulatory information on electromagnetic interference (EMI) refer to page 25.
1.9 Check Federal, State, and Local Codes
Check all relevant codes to make sure all product certifications, product listings, and building regulations
are met. Code compliance is the responsibility of the installer.
2.0 General Mounting Considerations (I-Beam, Glulam Beam, or Other Type of Truss System)
Each type of mounting system (I-beam, glulam, or other) requires a specific mounting bracket. Most are
available from MacroAir. Before installing fans, check with the contractor, building owner, or architect to
ensure the building structure is sound and will support the weight of the fan. MacroAir Technologies
provides guidelines for mounting fans; however, it is the sole responsibility of the building owner and
installer to ensure the safety of the mounting system, that the building structure is sound, and that the
installation complies with all federal, state, and local codes.
Fig 1

Page 9
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
2.1 Weight
A standard 20 foot 6-blade fan weighs about 230 pounds, the 10-blade version about 325 pounds,
including the standard mounting hardware. In inverted-blade applications designed to blow air upward
(very unusual), there is an additional down force of about 100 pounds due to fan thrust. We recommend
that a building structure be capable of holding approximately twice the stated hanging weight of the
fan. If there is some doubt of this, a professional contractor or architect should perform a thorough
evaluation of the building prior to purchasing fans.
2.2 Torque
The maximum torque (twisting force) that must be handled by the mounting system, including building
structure, occurs at fan startup. For a 20 foot fan, maximum potential starting torque is 300 ft-lbs. When
standard electrical controls are installed, the fan will never begin to approach this maximum because the
standard variable-speed control system uses soft-start technology. However, should the soft-start fail, or
when a fan is installed as a single-speed model without the variable speed control system (rare), full
torque might be applied to the mounting system, so it is important that it be adequate to withstand 300 ft-
lbs torque.
2.3 Safety Cable
A MacroAir fan should never be run without a properly installed safety cable, which is supplied with every
fan along with all required hardware. You must install safety cable for warranty to be in effect.
2.4 Close Clearances
The area within three feet of the blade tips when the fan is at rest is considered “close clearance”. It is
EXTREMELY DANGEROUS to mount the fans within “close clearance” of any object. We strongly
recommend not mounting the fan closer than 15% of its diameter to any object. If this is an issue,
mounting extensions and smaller fans are available from MacroAir.
2.5 Guy Cables
A running fan can sway due to a minor imbalance or because of wind. “Wind” may be only the air
movement the fan itself generates, or it may be actual wind if the fan is mounted outdoors or in open
areas. Since the mounting system is free swiveling, it will not stop fan movement, so it is imperative that
guy wires be properly installed. The primary considerations are angle and tension of the guy wires. See
Step 10 for more information.
2.6 Guards (except standard eco6 fan with integral guard)
If there is potential for people or objects to come in contact with a running fan, it is best to construct a
guard from angle iron and steel mesh, attaching it securely to the building structure. The guard should be
mounted with sufficient clearance so that no part of it can be pushed into the fan, with at least 18 inches
of clearance on all sides. We recommend 2” x 2” x 3/16” angle-iron for the frame, and, in most cases, 2” x
2” x 11” gage weldmesh (1/8” diameter wire on 2” centers) for the screen. However, mesh size should be
dependent on what objects might come in contact with the fan — if, for example, employees on lifts can
inadvertently get a finger into a fan, use smaller mesh or greater spacing — OSHA guidelines state that a
finger guard must prevent a finger entering into the guard within four (4) inches of the moving device, the
fan blades in this case. Refer to OSHA guidelines, paragraph 1910.212(a) (5) for more information.

Page 10
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
2.7 Universal Mounting Hardware
We recommend mounting the fan to a horizontal structural beam, but this is not always possible in
buildings with pitched roof construction. For that reason, our universal mount is designed to swivel freely in
order to allow the fan to hang in a level position regardless of the angle of the beam it is mounted to. Our
mounting hardware package includes clamps for use with standard steel I-beams, shims for thicker steel I-
beams, and all necessary nuts and bolts. For buildings with glulam beams (laminated wood), an
additional set of brackets, available from the factory, is required.
2.8 Maintenance
Before servicing the fan or control panel ensure all POWER IS OFF and locked out to avoid injury.
.
Control Panel
Occasional cleaning is advisable, especially when the panel is located in a dusty or dirty environment. A
can of compressed air, like that used for computer cleaning, works well to clean the inside of the panel.
Simply wipe down the outside of the enclosure with a cloth or duster periodically, if desired.
Power Unit
The gearbox is lubed for life, and we use thread locking compound on critical nuts and bolts. However, it
is a good idea to occasionally check that no nuts or bolts have vibrated loose. No other maintenance is
required.
Mounting Hardware
Check all mounting bolts annually to be sure they have not loosened. Also, check the safety cable and
guy wires to be sure they are not loose or frayed. Loose guy wires are more likely to break than tight ones,
and broken guy wires may fall into the fan. If a guy wire is loose, carefully check to be sure it is not
damaged, and re-tighten it.

Page 11
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
2 Installation Procedures
Step 1, Install mounting hardware
A) For glulam installations, attach the glulam brackets to the beam using ½” through bolts,
not supplied. Note, ½” lag screws, also not supplied, may be used as an alternative, but
will not provide as much mounting strength. Be sure the brackets line up with each other
and that the bottom of each bracket is flush with the bottom of the beam. For glulam
installations, attach the mount directly to the bracket using the supplied ½” x 2 ¾” bolts,
washers, and nylon lock nuts.
B) For steel I-Beam installations, mount so that the large plate is against the bottom of the
beam. Be sure the plate is at a 90 degree angle to the beam and centered. Place the
supplied clamps on top of the beam and attach them to the mount using the supplied
fasteners. For thicker I-beams, use the supplied shims between the clamp and the mount
as shown in figure 3.
Note: In all cases, be sure to thoroughly tighten all mounting bolts and nuts. The nylon lock nuts
help prevent loosening due to vibration, but there is no substitute for proper tightening. We
recommend that nylon lock nuts not be removed and reused because this will defeat the
nylon locking; instead, buy new nylon lock nuts from your local hardware store.
C) If an extension is to be used, attach it to the bottom of the universal mount using the
fasteners provided with the extension. Also, be sure to save the longer safety cable and
guy wire supplied with the extension; they will be needed in a later step.
D) Loop supplied safety cable (1/4 inch steel braided cable) over the beam and let it hang.
It will be attached once the power unit is installed. If using an extension, be sure to use
the longer safety cable supplied with the extension.
Fig 2
Fig 3

Page 12
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Step 2, Attach Power Unit To Mounting Hardware
A) We recommend using a scissor lift to install our fans. The best method is to place the
power unit hub-down on the lift and raise the lift until the power unit frame touches the
bottom of the universal mount or extension (if used).
B) Once the motor frame is in contact with the mount/extension, maneuver the power unit
as necessary to line up the mounting holes.
C) Securely attach the power unit to the mount/extension using the ½” x 1½” bolts, washers,
and nylon lock nuts included in the mounting hardware kit. Be sure to thoroughly tighten
all four bolts and nylon lock nuts to prevent vibration-related loosening. Correct
tightening is extremely important. Again, do not re-use nylon lock nuts.
Step 3, Attach Safety Cable
Refer to figure 4 as necessary. This step is required, omitting it will void manufacturer’s warranty!
A) Slide two of the supplied large cable clamps over each end of the safety cable.
B) Make a loop in one end of the cable, sliding the end back through the safety clamps.
C) Feed the other end of the safety cable through the loop, making sure that the cable
goes through the motor frame.
D) Repeat step B for this end of the cable.
E) Tighten the clamps securely, making sure that the u-bolts are over the free end of the
cable, see Figure 4.
Step 4, Mount The Motor Control Panel
Select a location for the MCP (Motor Control Panel) and mount securely.
A) The MCP should be mounted in the upright position, vertically, with the door opening to
the left. Do not mount so that the door opens downward. The mounting surface must be
non-flammable, away from sources of heat, dust, moisture, and vibration.
Fig 4

Page 13
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
B) The MCP should be mounted at least 5 feet outside of the swept area of the fan blades;
this will allow safe operation of the fan and still provide access to the MCP when the fan is
running.
C) Be sure to keep the lockable service disconnect located on the side of the MCP within
line of sight of the fan motor to comply with OSHA and local safety codes.
D) Mount the MCP, making sure the enclosure is firmly fixed to the mounting surface.
Step 5, Mount Remote Switchbox
Select a location for the remote switchbox and mount securely.
A) The remote switchbox should be no more than 100 feet away from the MCP.
B) Mount the remote switch box in a location that is easily accessible for personnel
authorized to operate the fan.
C) Locate the switch box in an area where it will be safe from damage caused by
unintended contact.
D) Securely mount the remote enclosure, making sure it cannot be easily detached by
incidental contact.
Step 6, Make Control Circuit Connections
A) Strip cable and conductors at both ends.
B) Install one supplied strain relief fitting in the remote switchbox and make appropriate
connections, referring to the wiring diagram (on page 28) packaged in the control panel
and/or the sticker inside the remote enclosure. Close up the remote enclosure.
C) Install the other supplied strain relief fitting in the MCP enclosure and make control circuit
connections at the terminal strip of the VFD located inside the MCP, see included wiring
diagram (on page 28). Do not make any incoming power or motor lead connections at
this time.
D) Ground the shield of the control circuit cable to the ground screw located in the lower
left corner of the VFD next to the MAINS terminal.
E) Daisy chain additional controllers if used, see included wiring diagram (on page 28).
Ground the shielding of the cable at the slave controller side only. There is no need to
specifically designate a “Master” drive — any drive may be used as either a master or
slave with no changes. If interfacing with any kind of automated building management
system, however, please consult factory as there may be additional programming
required.
F) Route the control circuit cables away from all incoming power and motor cables,
keeping them separated by at least 6 inches. When control circuit wiring must cross
power cables, make sure they do so at 90 degree angles to minimize interference.
Step 7, Make Motor Lead Connections
A) Verify controller voltage; this can be found on the lower left corner of the MCP, as well as
the sticker on the side of the VFD (see “input”).

Page 14
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
B) Use only the supplied motor cable for motor leads, be sure to attach all four wires — three
for power, one for ground. The 25 foot cable is recommended to prevent voltage and
frequency fluctuations, which could cause the motor to malfunction and/or be
damaged. Consult the factory if a longer cable is required.
C) Route motor cable away from all other power and control cables. Keep motor cable at
least 6 inches away from input power and control wiring. If the motor cable must cross
power cables or other motor control cables, make sure they do so at 90 degree angles to
minimize interference. Avoid long parallel runs to prevent signal crossover.
D) Correctly install supplied cable glands at both ends of the motor cable (see Figure 5).
i) Take the cable gland apart and slide the gland nut over the end of the cable,
threads facing the cable end.
ii) Slide the plastic and rubber cable gland insert over the end of the cable, with
the larger end toward the middle of the cable.
iii) Strip the outer insulation of the cable back approximately three inches, leaving
approximately half an inch of metal and foil braid sticking out past the outer
insulation.
iv) Slide the cable gland insert up the cable until it is flush with the outer insulation.
v) Peel the foil and braid insulation back and fold it down over the cable gland
insert.
vi) Cut off any inner (plastic) insulation that remains.
vii) Slide the threaded part of the cable gland over the end of the cable, long side
down. Work it down over the insert until only the “fingers” of the insert are visible,
turning either piece as necessary to ensure a proper fit.
viii) Slide the gland nut up and tighten it securely onto the gland.
E) Connect the ground wire to the green screw located inside of the motor junction box.
Fig 5

Page 15
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
F) Wire motor leads for the appropriate voltage, referring to Figure 6. Note that the top four
diagrams are for U.S. motors, while the bottom two are for CE motors, usually for use
outside the U.S. Be certain to wire the motor for the correct voltage — a mistake here
can ruin the motor and/or the VFD and is not covered under the factory warranty.
G) Connect motor ground wire to the ground bar located inside of the Control Panel.
Note: ALWAYS connect the ground wire of the included motor cable at both ends, MCP and motor.
H) Connect motor leads to terminals U, V, & W on the VFD.
Step 8, Install Guy Wires
If an extension is installed, be sure to use the longer guy wires packaged with it. Be sure to use four guy
wires, with two clamps per end (four per guy wire). Keep the angle formed by the guy wire and the floor
less than 45 degrees. If longer guy wire is required, it is available inexpensively at most hardware stores.
Eye bolts are recommended to attach the wires to the building structure.
Note: This step is REQUIRED — omitting it may void manufacturer’s warranty!
A) Be sure not to wrap the wire around any sharp corners to avoid fatiguing and fraying.
B) Attach the guy wires to the building structure.
i) Slide two of the supplied small cable clamps over one end of the wire.
ii) Feed that end of the wire through the eye bolt and back through the cable
clamps.
iii) Tighten the cable clamps securely, keeping the u-bolt side over the free end of
the cable — see figure 4 (in step 3 on page 12).
Fig 6

Page 16
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
C) Attach the guy wires to the loops on the lower section of the fan, one wire per individual
loop.
i) Slide two of the supplied small cable clamps over the near end of the wire.
ii) Feed that end of the wire through the guy wire loop on the fan and back
through the clamps, taking all the slack out of the cable.
iii) Slide one clamp approximately 18 inches (or as close to 18 inches as possible)
from the fan and tighten it securely — it needs to hold the free end of the wire in
place during the tensioning process.
iv) Position the other clamp about two inches from the fan and tighten it just far
enough to hold it in place.
v) Remove the rest of the slack, one guy wire at a time, using the included guy wire
wrench. It is advisable to put a level on the hub to be sure the fan remains
horizontal.
1) Attach the tool to a 3/8 inch drive ratchet.
2) Loop the tool through the free end of the guy wire between the
clamps and turn clockwise as far as possible.
3) Tighten the inner clamp to hold the tension.
4) Repeat until all excess slack is out of the wire.
vi) Loosen the outer cable clamps, pull the slack out of the free end of the wire, and
position the clamp about 18 inches from the inner one.
vii) Re-tighten the outer clamp and double-check that the inner clamp is tight. Be
sure the u-bolt is over the free end of the wire to prevent slipping.
viii) Repeat for all guy wires.
ix) Re-check all clamps for tightness.
Step 9, Install Fan Blades, Blade Safety Links, & Safety Link Extenders
A) Install the fan blades.
i) Be sure to orient the blades correctly — they should curve toward the floor (thin
edge down). Whisperfoil XL blades (our standard blade) will slide on easily either
way; Whisperfoil and Wickerbill blades are harder to install upside down, but can
be forced.
(If you are installing an inverted-blade fan (rare), the blades should curve away from
Fig 7

Page 17
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
the floor. ONLY install the blades in this direction if the hub is painted black and you
want the fan to blow air up.)
ii) Slide one blade over any hub winglet. Make sure it’s facing the right way!
iii) Line up the bolt holes in the blade with the holes in the winglet.
iv) Put a bolt from the included blade bolt pack through the outer hole, using a
washer on top of the blade.
B) Install safety links (often referred to as “boomerangs” because of their shape) and safety
link extensions. This step is REQUIRED — omitting it will void manufacturer’s warranty!
i) Line up one hole of a safety link with the inner hole of one wing. If desired, put a
bolt through just to hold it — don’t put a nut on it at this point, though.
ii) Line up the other hole of the safety link with the inner hole on the next wing.
Place a second safety link on top, lining up all three holes.
iii) Put a bolt through the holes — don’t use a washer on the top side of the blade.
iv) Slide the safety link extension over the bolts from the bottom side of the blade
and securely tighten an included nylon lock nut onto each of the bolts. Do not
use any washers! The safety link will bend when the nut closest to the hub is
tightened due to the angle of the hub winglets.
v) Repeat for the rest of the blades.
vi) Once the starting point is reached, pull out the positioning bolt from step i (if
used). Slide the end of the final safety link under the end of the first safety link.
Put the bolt (back) through and attach like the rest, being sure to install the
safety link extension on the underside of the blade.
C) Check that all bolts are tightened firmly. Blades should not rattle when the fan is running.
Step 10, Check Clearances And Guy Wire Tension For Safety
A) Rotate the fan slowly one time by hand to find the position and blade with the least
clearance from any possible obstructions. If necessary, reposition the fan to prevent any
dangerous conditions.
Note: At rest, the blade tips hang lower than they will be in operation due to gravity. For our largest fans,
this deflection can be approximately six inches.
B) Double check guy wire tension by attempting to move the fan in any horizontal direction
and by trying to pull down on the guy wires. They should be very difficult to move. If
there is visible slack in any guy wire or if any moves easily, re-tension them before
proceeding.
Fig 8

Page 18
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
Step 11, Install Guards If Necessary
Refer to Section 2.6 of the MacroAir Installation Manual for guidelines.
Step 12, Install Input Power
A) Verify that input power voltage and number of phases match that of the MCP.
B) Determine the appropriate size for the input circuit by multiplying the maximum input
amperage of the VFD — found on the door of the MCP and on the included control
panel drawing (wiring diagram) — by the number of fans to be placed on the circuit. Be
sure the breakers used match the voltage of the VFD. Each MCP contains input fuses
providing individual circuit protection for each unit, but an appropriately-sized input
breaker should still be installed.
C) Connect a ground wire from the supply panel to the ground bar located inside of MCP.
Note: ALWAYS connect the grounding bar in the MCP to ground at the power panel — when pulling power
from the main panel; be sure to pull a full sized ground.
D) Connect input power leads to the disconnect switch located on the side of the MCP at
the proper terminals.
Step 13, Verify Proper Operation
Leave the door of the MCP open during this process so the front of the VFD is visible.
A) Turn the service disconnect to the On position. When power is applied, the green On
indicator (located on the front of the VFD) will light.
B) Adjust the speed control knob (located on the remote switchbox) to 4.
C) Turn the For-Off-Rev (Forward/ Off/ Reverse) switch (located on the remote switchbox) to
the For (Forward) position.
D) After a 15 second delay, the fan will begin to accelerate slowly.
E) Verify proper rotation with the For-Off-Rev switch in the For position: the rotor should be
turning in the counter-clockwise direction when viewed from the floor — see figure 9.
Properdirectionofbladerotation
asviewedfromouterendofblade
Fig 9

Page 19
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
F) If the fan is turning the wrong way on initial startup, follow the procedure below:
i) Verify that the For-Off-Rev switch is in the For position.
ii) If so, turn the switch to the Off position.
iii) Carefully remove the remote box faceplate with the switches attached and turn
it over. Verify that the wiring to the For-Off-Rev switch matches the wiring
diagram (there should be a sticker inside the remote enclosure). If it’s wrong,
correct it and re-test the fan. Reattach the faceplate (before testing).
iv) If step iii does not solve the problem, turn off the disconnect switch on the MCP
and snap the small cover off the VFD. Ensure that the wiring matches the wiring
diagram — this can be found on the included control panel drawing as well as
on a sticker inside the control panel door. If this wiring is wrong, correct it,
replace the cover, and test the fan again.
v) If step iv does not solve the problem, simply switch any two of the three power
wires from the MCP to the fan motor, either at the MCP or at the motor. Turn the
power back on and re-test the fan.
vi) If none of these steps fix the problem (extremely unlikely,) contact the factory for
further assistance.
vii) Be sure the remote box is re-assembled and the cover is back on the VFD before
proceeding.
G) Adjust the speed control to 9 and verify full speed operation with no Fault or Warning
indicators lit on the VFD. Contact factory if fault/warning condition occurs.
H) Close up the MCP.
I) Adjust fan speed and direction for desired operation.

Page 20
MacroAir Technologies Inc. www.macro-air.com Toll Free: 866-668-3247 Build: January 9 2009
3 Installation Procedures For eco6 Guard Fan
Step 1, Install Mounting Assembly
For Wall-Mounted Applications
A) Mark a level line on the wall at the desired mounting height to locate the top edge of the
upper mount plate.
B) Use the mount as a template to carefully mark the locations of the mounting holes on the
wall. There should be six holes total: four in the upper plate and two in the lower plate.
Be sure to align the top edge of the upper mount plate with your level line.
C) Remove the mount from the wall and pre-drill mounting holes for the appropriate
mounting fasteners.
For concrete or masonry walls:
i) Insert Red Head or equivalent 1/2” self-anchoring studs (not included) into the
mounting holes, properly securing them according to manufacturer’s instructions.
ii) Slide the mount plates over the studs and attach using nylon lock nuts and flat
washers, being careful not to over-tighten.
Note: We recommend that nylon lock nuts not be removed and reused because this
will defeat the nylon locking; instead, buy new nylon lock nuts from your local
hardware store.
For wood surfaces (wood studs): Before mounting the fan to a wood surface, ensure that
the structure will safely support the fan’s weight (see spec. sheet).
i) Line the mount assembly up with the mounting holes.
ii) Insert 1/2” lag bolts (not included) into the holes, using washers to maximize the
hold. Be sure that you use bolts long enough to support the weight of the fan.
Tighten the bolts securely, but do not over-tighten them.
Fig 10