MAG NX Series User manual

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
1
User Manual
Руководство пользователя
Systems / Системы:
NX 10 NX 10A NX 10i
NX 12 NX 12A NX 12i
NX 15 NX 15A NX 15i
NX SERIES

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
2
Contents \ Содержание
Contents \ Содержание............................................................................................................................................................2
Panel A. Dimensions ....................................................................................................................................................................4
1. Safety instructions ...................................................................................................................................................................9
2. Regulatory information...................................................................................................................................................... 10
3. NX series......................................................................................................................................................................................11
3.1. Introduction ........................................................................................................................................................................11
3.2. NX series speaker models............................................................................................................................................11
4. Specifications...........................................................................................................................................................................12
5. System operation...................................................................................................................................................................14
5.1. Rigging.................................................................................................................................................................................14
5.2. Flying via M10 mounting points..............................................................................................................................14
5.3. Eye-bolt orientation......................................................................................................................................................14
5.4. Pole mounting..................................................................................................................................................................15
5.5. Mounting using flying adapter................................................................................................................................15
5.6. Wall or ceiling mounting using the rotation bracket.....................................................................................16
5.7. Wall or ceiling mounting using the horizontal bracket..................................................................................17
5.8. Passive speakers............................................................................................................................................................ 18
5.8.1. Passive connections.............................................................................................................................................. 18
5.9. Powered speakers ..........................................................................................................................................................19
5.9.1. Mains connection....................................................................................................................................................20
5.9.2. Signal connections ................................................................................................................................................20
5.9.3. Amplifier controls...................................................................................................................................................20
6. Standard contents.................................................................................................................................................................21
7. Accessories ...............................................................................................................................................................................22
8. Warranty and assistance...................................................................................................................................................23
8.1. Product warranty...........................................................................................................................................................23
8.2. Assistance.........................................................................................................................................................................23

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
3
1. Правила техники безопасности ..................................................................................................................................25
2. Нормативная информация ............................................................................................................................................26
3. NX серия................................................................................................................................................................................... 27
3.1. Вступление....................................................................................................................................................................... 27
3.2. Системы NX серии....................................................................................................................................................... 27
4. Спецификации ......................................................................................................................................................................28
5. Эксплуатация.........................................................................................................................................................................30
5.1. Установка ..........................................................................................................................................................................30
5.2. Подвес с помощью точек М10 .............................................................................................................................30
5.3. Размещение рым-болтов при подвесе...........................................................................................................30
5.4. Установка на стойки....................................................................................................................................................31
5.5. Подвес с помощью подвесного адаптера .....................................................................................................31
5.6. Установка на стену или потолок с использованием поворотного кронштейна .....................32
5.7. Установка на стену или потолок с использованием горизонтального кронштейна ............33
5.8. Пассивные системы....................................................................................................................................................34
5.8.1 Пассивное подключение...................................................................................................................................34
5.9. Активные системы.......................................................................................................................................................35
5.9.1. Подключение питания.......................................................................................................................................36
5.9.2. Подключение сигнала.......................................................................................................................................36
5.9.3. Управление усилителем...................................................................................................................................36
6. Комплект поставки............................................................................................................................................................. 37
7. Аксессуары..............................................................................................................................................................................38
8. Гарантия и поддержка.....................................................................................................................................................39
8.1. Гарантия продукта ......................................................................................................................................................39
8.2. Поддержка......................................................................................................................................................................39

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
4
Panel A. Dimensions
NX 10
NX 12
319mm
[12.54"]
600mm
[23.62"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"] 40mm
[1.57"]
40mm
[1.57"]
160mm
[6.30"]
170mm
[6.69"]
336mm
[13.23"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
379mm
[14.92"]
650mm
[25.59"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
185mm
[7.28"]
218mm
[8.57"]
367mm
[14.45"]
40mm
[1.57"]
40mm
[1.57"]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
5
NX 15
NX 10A
436mm
[17.17"]
730mm
[28.74"]
40mm
[1.57"]
40mm
[1.57"]
235mm
[9.25"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
423mm
[16.65"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
249mm
[9.81"]
423mm
[16.65"]
319mm
[12.54"]
600mm
[23.62"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
160mm
[6.30"]
170mm
[6.69"]
336mm
[13.23"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
6
NX 12A
NX 15A
379mm
[14.92"]
650mm
[25.59"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"] 40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
185mm
[7.28"]
218mm
[8.57"]
367mm
[14.45"]
436mm
[17.17"]
730mm
[28.74"]
235mm
[9.25"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
249mm
[9.81"]
423mm
[16.65"]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
7
NX 10i
NX 12i
40mm
[1.57"]
40mm
[1.57"]
336mm
[13.23"]
170mm
[6.69"]
40mm
[1.57"]
319mm
[12.54"]
600mm
[23.62"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
218mm
[8.57"]
367mm
[14.45"]
40mm
[1.57"]
379mm
[14.92"]
650mm
[25.59"]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
8
NX 15i
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
40mm
[1.57"]
423mm
[16.65"]
249mm
[9.81"]
436mm
[17.17"]
730mm
[28.74"]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
9
1. Safety instructions
1. Read these instructions carefully.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not use near heat sources such as stoves, heat registers,
radiatiors or other equipment (including amplifiers) that
produces heat.
9. Do not use the unit near open fire sources.
10. Connect the unit only to the electric network with grounding.
Use only electic plugs that provide grounding.
11. Protect the power cord from being walked on, pinched, or
otherwise damaged.
12. Use only accessories specified by the manufacturer.
13. Unplug this unit during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the system has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the unit, the unit has been exposed
to rain or moisture, does not operate normally, or has been
dropped.
15. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS SYSTEM UNIT TO RAIN OR
MOISTURE.
THIS UNIT CONTAINS POTENTIALLY LETHAL VOLTAGES.
TO PREVENT ELECTRIC SHOCK OR HAZARD, DO NOT
REMOVE THE AMPLIFIER MODULE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. 1
INSTALLING OF THIS UNIT MUST BE PERFORMED ONLY BY
QUALIFIED TRAINED PERSONNEL FOLLOWING APPLICABLE
SAFETY RULES. DO NOTALLOW INSTALLATION OF THIS UNIT
IF INSTALLATION HARDWARE IS BROKEN, BENT, PARTS ARE
MISSING OR IS OTHERWISE DAMAGED.
1 - for powered speakers only
The triangle with the lightning bolt is used to alert the
user to the risk of electric shock.
The triangle with the exclamation point is used to
alert the user to important operating or maintenance
instructions.
The CE-mark indicates the compliance with the low
voltage and electromagnetic compatibility.
Symbol for earth/ground connection.
Symbol indicating that the equipment is for indoor use
only.
Symbol for conformity with Directive 2002/96/EC and
Directive 2003/108/EC of the European Parliament on
waste electrical and electronic equipment (WEEE).
WARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT ATTEMPT TO OPEN ANY PART OF THE
UNIT. NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO COMPLETELY DISCONNECT THIS APPARATUS
FROM THE AC MAINS, DISCONNECT THE POWER
SUPPLY CORD PLUG FROM THE AC RECEPTACLE.
THE MAINS PLUG OF THE POWER SUPPLY CORD
MUST REMAIN READILY ACCESSIBLE.
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE, DRIPPING OR SPLASHING LIQUIDS.
OBJECTS FILLED WITH LIQUIDES, SUCH AS VASES,
SHOULD NOT BE PLACED ON THIS APPARATUS.
CONNECTIONS TO THE MAINS SHALL BE DONE ONLY
BY AN ELECTROTECHNICALLY SKILLED PERSON
ACCORDING TO THE NATIONAL REQUIREMENTS OF
THE COUNTRIES WHERE THE UNIT IS SOLD.
EXPLANATIONS OF GRAPHICAL SYMBOLS IMPORTANT SAFETY INSTRUCTIONS
= =
=
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
10
2. Regulatory information
FCC COMPLIANCE NOTICE
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuantto part 15 ofthe FCC Rules.These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment o and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
EC DECLARATION OF CONFORMITY
Manufacturer:
MAG Audio LLC
Merezhna 2
Bila Tserkva, Kyiv region
09112 Ukraine
We declare under our sole responsibility that
product models:
NX 10-8, NX 12-8, NX 15-8, NX 10A, NX 12A,
NX 15A, NX 10i, NX 12i, NX 15i
intended for use as:
professional speaker systems
are in conformitywith the provisions ofthe following
EC Directives, including all amendments, and with
national legislation implementing these directives:
- 2006/95/EC Low Voltage Directive
- 2004/108/EC Electromagnetic Compatibility Directive
- 2002/95/CE RoHs Directive
The following harmonized standards are applied:
EN 55103-1:2009 /A1:2012
EN 55014-1:2006 /A1:2009 /A2:2011
EN 55022:2010 /AC:2011
EN 61000-3-2:2006 /A1:2009 /A2: 2009
EN 61000-3-3:2013
EN 61000-3-11:2000
EN 61000-3-12:2011
EN 55103-2:2009 /IS:2012
EN 61000-4-2:2009
EN 61000-4-3:2006 /A1:2008 /IS1:2009 /A2:2010
EN 61000-4-4:2012
EN 61000-4-5:2006
EN 61000-4-6:2014
EN 61000-4-11:2004
EN 60065:2002 /A1:2006 /A11:2008 /A2:2010 /A12:2011
Bila Tserkva,
22 January 2019
Alexey Asanov
CEO
For compliance questions: inf[email protected]

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
11
3. NX series
3.1. Introduction
NX series represents solid and powerful solutions
for fixed installations as well as demanding mobile
soundapplications.NXfull-rangecabinetsarebased
on top-line neodymium magnet transducers and
high-frequency drivers fitted with demodulation
rings and copper caps for less distortions and
improved voice coil cooling, allowing for prolonged
high-SPL operation while preserving clarity and
intelligibility.
Powered cabinets employ state-of-the-art
amplification from Powersoft® and provide ease
of use with carefully adjusted built-in presets.
Passive NX speakers are fitted with low-distortion
crossovers with optimal transfer characteristics,
allowing for controlled tuning with external
amplification.
Durable cabinets, made of high-quality birch
plywood, are readyto face harsh touring conditions.
At the same time, optionally available weatherproof
treatment extends series’ usability even further into
harsh environmental conditions, including theme
parks, skating rinks, and swimming pools.
With outstanding performance and high reliability,
NX series is designed to meet demands of various
applications, where uncompromised sound quality
is a must.
3.2. NX series speaker models
NX series includes following speaker models:
NX 10-8 part number 00-0004278
NX 10A part number 00-0004207
NX 10i part number 00-0005605
NX 12-8 part number 00-0004279
NX 12A part number 00-0004208
NX 12i part number 00-0004809
NX 15-8 part number 00-0004280
NX 15A part number 00-0004209
NX 15i part number 00-0004315

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
12
4. Specifications
System
NX 10
Passive full-range speaker
NX 10i
Installation full-range
speaker
NX 12
Passive full-range speaker
NX 12i
Installation full-range
speaker
NX 15
Passive full-range speaker
NX 15i
Installation full-range
speaker
Frequency Response (−10dB) 65 - 19000 Hz 60 - 19000 Hz 50 - 19000 Hz
Max SPL 1133 dB 134 dB 134,5 dB
Sensitivity (1W/1m) 97 dB 98 dB 98,5 dB
LF Driver 10”, 3" VC 12”, 3" VC 15", 3" VC
HF Driver 1,5”, 2,8" VC 1,5”, 2,8" VC 1,5”, 2,8" VC
Nominal Coverage Angle
(Horizontal × Vertical) 80° x 70° 80° x 70° 80° x 70°
Impedance 8 Ohm 8 Ohm 8 Ohm
Nominal power 2500 W 500 W 500 W
Connectors 2x Neutrik Speakon (NX 10)
2x Barrier strip (NX 10i)
2x Neutrik Speakon (NX 12)
2x Barrier strip (NX 12i)
2x Neutrik Speakon (NX 15)
2x Barrier strip (NX 15i)
Dimensions (W×H×D), mm 319x610x336 mm 379x660x367 mm 436x740x423 mm
Net weight, kg 19 kg 22 kg 26 kg
Shipping weight, kg 22 kg 25 kg 29 kg
Mounting 10x M10 mounting points,
35mm pole socket (NX 10)
10x M10 mounting points,
35mm pole socket (NX 12)
10x M10 mounting points,
35mm pole socket (NX 15)
Enclosure material Plywood; wear-resistant
paint
Plywood; wear-resistant
paint
Plywood; wear-resistant
paint
Grill Steel grill, polymer protective
net
Steel grill, polymer protective
net
Steel grill, polymer protective
net
1 - peak value, calculated according to AES 2 - 2012
2- based on transducer power measured according to AES 2 - 2012

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
13
System NX 10A
Powered full-range speaker
NX 12A
Powered full-range speaker
NX 15A
Powered full-range speaker
Frequency Response (−10dB) 55 - 20000 Hz 50 - 20000 Hz 45 - 20000 Hz
Max SPL (calculated) 134 dB 135 dB 135,5 dB
LF Driver 10”, 3” VC 12”, 3” VC 15”, 3” VC
HF Driver 1,5”, 2,8” VC 1,5”, 2,8” VC 1,5”, 2,8” VC
Nominal coverage angle
(Horizontal x Vertical) 80° x 70° 80° x 70° 80° x 70°
Amplifier power 900+500 W 900+500 W 900+500 W
Amplifier Class D, fan cooling, DSP with
phase-linear FIR
Class D, fan cooling, DSP with
phase-linear FIR
Class D, fan cooling, DSP with
phase-linear FIR
Input sensitivity 0 dBV (1 V RMS) 0 dBV (1 V RMS) 0 dBV (1 V RMS)
Connectors XLR input, XLR output,
Powercon mains
XLR input, XLR output,
Powercon mains
XLR input, XLR output,
Powercon mains
Dimensions (WxHxD) 319x610x336 mm 379x660x367 mm 436x740x423 mm
Net weight 22 kg 25 kg 29 kg
Shipping weight 25 kg 28 kg 32 kg
Mounting 10x M10 mounting points,
35mm pole socket
10x M10 mounting points,
35mm pole socket
10x M10 mounting points,
35mm pole socket
Enclosure material Plywood; wear-resistant
paint
Plywood; wear-resistant
paint
Plywood; wear-resistant
paint
Grill Steel grill, polymer protective
net
Steel grill, polymer protective
net
Steel grill, polymer protective
net

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
14
5. System operation
5.1. Rigging
NX series systems are equipped with M10 mounting point adapters and pole mount adapters systems for
versatile applications.
Rigging must be performed only by trained personnel following the established safety rules.
MAXIMUM WEIGHT RESTRICTIONS MUST BE FOLLOWED AT ALL TIMES!
MAKE SURE THE SUPPORT STRUCTURE IS CAPABLE OF HOLDING THE APPLIED WEIGHT WHILE
SUSPENDING THE SYSTEM!
5.2. Flying via M10 mounting points
Required accessories:
VA-0016 (part No. 00-00003695)
Dierent options are available while flying NX series full-range speakers using integrated M10 flying
points.
5.3. Eye-bolt orientation
While flying, applied force must be in the plane of the
VA-0016 eyebolt’s ring. It is prohibited to arrange the rig
in the way that force is at the angle from the eyebolt’s ring
plane.
Right Wrong

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
15
5.4. Pole mounting
Accessories:
N-BOX-4 (part No. 00-00003474)
SAT-3T (part No. 00-00003644)
NX series full range speakers are equipped
with pole mount adapter, which allows
installing them onto standard speaker
stands, or, via distance poles, onto
subwoofers equipped with pole mount
adapters.
5.5. Mounting using flying adapter
Accessories:
ANX12 (part No. 00-0005433)
ANX15 (part No. 00-0005434)
VA-0012 (part No. 00-00003593)
1. Remove three top M10 bolts from
mounting points and position ANX12 (for NX
10, NX 10A, NX 10i, NX 12, NX 12A and NX
12i) or ANX15 (for NX 15, NX 15A and NX 15i)
flying adapter to fit mounting points (pic. 1.)
2. Use three M10 bolts to secure ANX12 or
ANX15 flying adapter in place (pic. 2.)
3. VA-0012 omega shackle may be used
to suspend the NX system with ANX12 or
ANX15 flying adapters (pic. 3.)
1 2 3

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
16
5.6. Wall or ceiling mounting using
the rotation bracket
Accessories:
LNX10 (part No. 00-0005435)
LNX12 (part No. 00-0005437)
LNX15 (part No. 00-0005436)
1. Remove two top M10 bolts from
mounting points and position LNX10 (for
NX 10, NX 10A and NX 10i), LNX12 (for NX
12, NX 12A and NX 12i) or ANX15 (for NX 15,
NX 15A and NX 15i) rotation bracket to fit
mounting points (pic. 1.)
2. Use two M10 bolts to secure LNX10,
LNX12 or LNX15ANX12 or ANX15 rotation
bracket in place (pic. 2.)
3. Use winches on each side of the cabinet
to adjust vertical tilt (pic. 3, 4.) NX series
speaker with LNX10, LNX12 or LNX15
may be mounted to wall or ceiling using
mounting holes of the rotation bracket.
1
3
2
4

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
17
5.7. Wall or ceiling mounting using
the horizontal bracket
Accessories:
HNX10 (part No. 00-0005438)
HNX12 (part No. 00-0005439)
HNX15 (part No. 00-0004318)
1. Remove four M10 bolts from mounting
points and position HNX10 (for NX 10, NX
10A and NX 10i), HNX12 (for NX 12, NX 12A
and NX 12i) or HNX15 (for NX 15, NX 15A and
NX 15i) horizontal bracket to fit mounting
points (pic. 1.)
2. Use two M10 bolts to secure HNX10,
HNX12 or HNX15 horizontal bracket in place
(pic. 2.)
3. Use winches on each side of the cabinet
to adjust vertical tilt (pic. 4, 5.) NX series
speaker with HNX10, HNX12 or HNX15
may be mounted to wall or ceiling using
mounting holes of the horizontal bracket.
1
3
4
2
5

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
18
Made in Ukraine
INPUT
www.mag-audio.com
NX 10, NX 12, NX 15
connection plate
NX 10i, NX 12i, NX 15i
connection plate
1. LABEL FIELD: name of the
system, along with its basic
parameters is noted here.
2. SERIAL NUMBER FIELD:
sticker with the systems
serial number is located here.
NEVER REMOVE THE SERIAL
FROM THE SYSTEM, AS IT
IS IMMEDIATE WARRANTY
VOID.
3. PARALLEL INPUTS: the
pair of parallel Neutrik®
Speakon connectors. Use this
connectors to connect power
amplifier and to feed the
signal to the parallel system
(optional).
4. INPUT: pair of screw
terminals. Use these to
connect power amplifier.
Made in Ukraine
NX series passive connection diagram
5.8.1. Passive connections
Suggested accessories:
CN-0031 (part No. 00-00004271)
CN-0032 (part No. 00-00004272)
Use power amplifier with DSP or power amplifiers
with external speaker processor with NX series
passive systems.
MAKE SURE TO USE HIGH PASS FILTER FOR ALL
NX SERIES SYSTEMS TO PREVENT EXCESSIVE
CONE MOVEMENT, RESULTING IN TRANSDUCER
DAMAGE OR FAST DETERIORATION.
Recommended HPF settings, suggested power
amplifier ratings, and connection pins are found in
table below:
System Amplifier power Amplifier impedance Connection pins Recommended HPF
NX 10 500 - 1000 W 8 Ohm +1 -1 60 Hz or higher, 18 dB/oct min
NX 10i 500 - 1000 W 8 Ohm + - 60 Hz or higher, 18 dB/oct min
NX 12 500 - 1000 W 8 Ohm +1 -1 55 Hz or higher, 18 dB/oct min
NX 12i 500 - 1000 W 8 Ohm + - 55 Hz or higher, 18 dB/oct min
NX 15 500 - 1000 W 8 Ohm +1 -1 50 Hz or higher, 18 dB/oct min
NX 15i 500 - 1000 W 8 Ohm + - 50 Hz or higher, 18 dB/oct min
1
3
2
5.8. Passive speakers
1
2
4
DSP AMPLIFIER
Speakon-Speakon
cable
Speakon-Speakon
cable
Speakon-2 wire
cable
Speakon-2 wire
cable
NX series passive
full-range system
NX series passive
full-range system
NXi series passive
full-range system
NXi series passive
full-range system

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
19
NX 10A, NX 12A, NX 15A
amplifier
5. VOLUME KNOB:
used for adjusting
the volume of the
system. Remember to
turn the volume down
before connecting/
disconnecting INPUT or
LINK connectors.
6. LIMIT LED: is lit when
limiter is operational,
indicating excessive
signal through the
system.
7. READY LED: is lit
when system is fully
operational.
8. HPF 100 Hz BUTTON:
engages a 100 Hz high-
pass filter for usage with
subwoofer.
9. MID CUT BUTTON:
engages a mid-cut EQ
contour.
10. HF BOOST
BUTTON: engages a
high frequency boost
EQ contour.
11. INPUT CONNECTOR:
used for connecting the
system to the signal
source (mixing console
etc.)
12. LINK CONNECTOR:
used for linking
additional compactible
system to the same
signal source.
13. HEAT SINK: do not
close the ventilation
openings on the heat
sink, as it may cause the
system to overheat and
switch o by itself.
14. MAINS IN: used
for connecting mains
supply to the system.
15. MAINS OUT: used
for feeding the mains
supply to the additional
system.
5
6
8 9 10
7
11
13
14
15
12
5.9. Powered speakers

NX Series User Manual rev 1.00
[e-mail] Tel./Fax: [phone] www.mag-audio.com
20
5.9.1. Mains connection
NX series powered systems are supplied with CN-0010 PowerCon-E/F CEE 7/7 mains cable (part number
00-00005561). Use only original or supplied by manufacturer mains cables!
NX series powered systems are equipped with PowerCon B mains power outlets for mains link to additional
NX series powered system.
NX series systems’ nominal mains power specifications: AC 220V, 50/60 Hz.
Nominal voltage tolerance: 100 - 250 V.
To power up the system, connect the mains cable to the system, then to the power outlet.
To completely power down the system, disconnect the mains cable from the power outlet.
5.9.2. Signal connections
NX series systems are equipped with XLR INPUT and XLR LINK connectors for signal connection.
Use of balanced XLR connector cables is recommended. In case when balanced XLR connections are not
available, unbalanced XLR connection is acceptable.
For linking the additional system to the same signal bus LINK connector may be used.
1
2
3
Shield (Ground)
Plus (+)
Minus (-)
Balanced XLR Plug connections
1
2
3
Shield (Ground)
Plus (+)
Shield (Ground)
Unbalanced XLR Plug connections
NX series powered signal connection diagram
5.9.3. Amplifier controls
Use several available NX series speaker system’s
amplifier controls to set up the entire system:
HPF 100Hz: provides a 100Hz high-pass filter
to seamlessly couple the full-range system with
powered subwoofer.
MID CUT: engages a mid frequency cut contour for
loudness eect, or cutting out harsh presense for
more comfortable background music experience.
HF BOOST: engages a high-frequency contour to
compensate for loss for far-throw applications.
XLR-XLR cable XLR-XLR cable
NX series
powered
full-range system
NX series
powered
full-range system
NX series
powered
full-range system
NX series
powered
full-range system
XLR-XLR cable XLR-XLR cable
Tosignal source