Magicshine MONTEER 12000 User manual

EN
MONTEER 12000
USER MANUAL
APP PAIRING NAME: M2-B0

DANGER
1. To prevent inadvertent switching on, please
unplug the connection cable between the light unit
and the battery pack before transport or storage.
2. DO NOT shine the light directly into human eyes.
This may cause temporary blindness or permanent
damage to the eyes.
CAUTION
1. DO NOT leave the device or batteries exposed to a
heat source or in a high-temperature location that
may exceed 75℃, such as in the sun in an
unattended vehicle.
2. DO NOT short-circuit the charging or discharging
port with any metal objects.
3. DO NOT disassemble or modify the light or any of
the included items, which could cause fire or death!
NOTICE
1. Fully recharge the light during long-time storage.
2. Please protect the lens surface from scratches, at
this may affect the brightness output.
WARNING

1*MJ-6398
battery pack
1*MONTEER 12000
IN THE BOX
1*MJ-6508 remote
control (incl. strap)
1*Helmet mount 1*Two-sided
handlebar mount
4*Nylon shims
2*Helmet
mounting straps
2*Battery
mounting straps
1*Warranty card1*USB-C
charging cable
1*Extension cable
DANGER
1. To prevent inadvertent switching on, please
unplug the connection cable between the light unit
and the battery pack before transport or storage.
2. DO NOT shine the light directly into human eyes.
This may cause temporary blindness or permanent
damage to the eyes.
CAUTION
1. DO NOT leave the device or batteries exposed to a
heat source or in a high-temperature location that
may exceed 75℃, such as in the sun in an
unattended vehicle.
2. DO NOT short-circuit the charging or discharging
port with any metal objects.
3. DO NOT disassemble or modify the light or any of
the included items, which could cause fire or death!
NOTICE
1. Fully recharge the light during long-time storage.
2. Please protect the lens surface from scratches, at
this may affect the brightness output.
1*3mm hex key

OPERATING INSTRUCTIONS
REMOTE CONTROL PAIRING:
1. Before first use, please open the remote's battery
compartment, remove the insulating spacer,
reinsert the battery, then cover the battery
compartment, and the indicator on the remote will
flash blue.
2. Before pairing, be sure to connect the light unit
and battery pack, then long press the light button
for 1 second to turn the light on.
3. With the light on, press and hold the "○" and "□"
buttons on the remote for about 10 seconds until
the indicator alternately flashes blue to enter
pairing mode. Then, put the remote close to the
light until the indicators on the remote and light
unit are constantly blue for 2 seconds.
4. Pairing is successful, and the remote control can
work normally.

REMOTE CONTROL OPERATION:
ON/OFF: Press and hold the "○" or "□" button for 1
second
ADJUST BRIGHTNESS: Click the "○" button
CHANGE MODE: Double click the "○" button
FLASH MODE: Double click the "□" button
FULL OUTPUT MODE (12000LM): Click the "□"
button to go into full output mode and click the
"○" or "□" button to return to the previous mode.
*The remote control will enter sleep mode if the
light is turned off for more than 48 hours without
any operation. Click the light's button to activate it
or long-press the light's button to turn it on, and
the remote control will work normally.
LIGHT BUTTON OPERATION:
ON/OFF: Press and hold the button for 1 second
ADJUST BRIGHTNESS: Click the button
CHANGE MODE: Double click the button

3. Press the "○" or "□" button on the remote control to
display the remaining battery level of the battery pack.
1. Display the remaining power in real-time when the
light is on, or click to display the power when the
light is off.
2. When charging, the four LEDs will cycle through
until the charging is completed.
BATTERY INDICATOR:
CHARGING / BATTERY INDICATOR
Green: 100%-26%
Red: 25%-11%
Flashing red: 10%-1%
Four LEDs constant green: 100%-76%
Three LEDs constant green: 75%-51%
Two LEDs constant green: 50%-26%
One LED constant green: 25%-11%
One LED flashing red: 10%-1%
Standard charging time approx. 3 hrs (20V 3A) /
9 hrs (12V 3A) / 11.5 hrs (9V 3A) / 16.5 hrs (5V 2A)

OUTPUT / RUNTIME
3. Press the "○" or "□" button on the remote control to
display the remaining battery level of the battery pack.
85h
35h
7h
2.5h
19h
121h
10h
33h
37h
11.5h
300LM
1500LM
2500LM
1000LM
3000LM
6000LM
12000LM
0-3000LM
800-3000LM
800LM
FLOODLIGHT
MODE
SPOTLIGHT
MODE
FLASH MODE
ECO
LOW
MEDIUM
HIGH
ECO
LOW
MEDIUM
HIGH
DAY FLASH
NIGHT FLASH
*The Day flash and Night flash can only be
accessed through the remote control.
*The above are the factory default settings. To
customize modes, please refer to the APP manual.
*All data are measured in accordance with
ANSI/NEMA FL 1-2009. The test was conducted at
a temperature of 25°C and a wind speed of 25
km/h. The runtime may vary depending on external
temperature and ventilation conditions, and these
deviations may affect the result of testing.
Standard charging time approx. 3 hrs (20V 3A) /
9 hrs (12V 3A) / 11.5 hrs (9V 3A) / 16.5 hrs (5V 2A)

HOW TO INSTALL
2. INSTALL ON HANDLEBAR (The mount fits handlebar
stems smaller than 70mm. Select the appropriate size
shim for 31.8mm or 35mm handlebars.)
1. BATTERY PACK MOUNTING
1
1
3 4
2
2
Nylon shim

3. REMOTE CONTROL MOUNTING
4. INSTALL ON HELMET
1
2
Adhesive velcro hook side up
1. 2. 3.