Magikist MagikTimer Plus User manual

1.0 SWITCH SETTINGS
To set a switch ON, depress the right side of the switch until it clicks into position
down. To turn a switch OFF, depress the left side until it clicks into position down.
1.1 COIN SETTING
Set the switches labelled COINS TO START such that the total the number of
coins required to start the timer. For example, to start the timer on 3 coins, set
switches 1 and 2 on. To start the timer on 6 coins, set switches 2 and 4 on. If all
the coin switches are off, the timer will require 16 coins to start.
1.2 TIME SETTING
Set the switches labelled SECONDS PER COIN such that the total the number of
seconds per coin that the timer is to operate for. For example, to configure the
timer for 30 seconds per coin, set switches 2, 4, 8, and 16 ON. To configure the
timer for 40 seconds per coin, set switches 8 and 32 ON. If all the time switches
are OFF, the timer will be set for 1 second per coin. The total time that the timer
will operate for, once started, is equal to the seconds per coin multiplied b the
coins to start. Coins deposited while the timer is operating will result in additional
time being added to the total time (each pulse will add the value of the seconds
per coin to the time left). The maximum time that ma be accumulated is 9 hours,
6 minutes, and 7 seconds (timers with serial numbers previous to 5380 have a
maximum accumulated time of 68 minutes and 15 seconds).
1.3 3-SECOND START DELAY
When the switch labelled 3secStartDela is set ON, the timer will wait for 3
seconds after the required number of coins have been deposited before starting. If
this switch is OFF, the timer will start immediatel when the required number of
coins have been deposited.
1.4 1-COIN RESTART
When the switch labelled 1CoinRestart is set ON, the timer can be restarted with a single coin b depositing a coin at an time
within the 20 second time period after time has expired. Once the 20 second time period has finished, the full number of coins to
start the timer is required. The timer will flash a light if attached to the 1COIN RESTART terminal during the 20 second time period
to indicate that the timer can be restarted with a single coin. If this switch is OFF, the full number of coins to start the timer will be
required once time has expired.
1.5 LAST MINUTE ALERT
The switch labelled LMA/1minCont and LMA/5secPulse determines how a horn or light attached to the LAST MINUTE ALERT
terminal functions. When set to LMA/5secPulse, the timer pulses the LAST MINUTE ALERT terminal for 5 seconds when there is 1
minute of time remaining (this setting is t picall chosen when a horn is connected to the LAST MINUTE ALERT terminal). When
set to LMA/1minCont, the timer turns the LAST MINUTE ALERT terminal on continuousl for the last minute of time (this setting is
t picall chosen when a light is connected to the LAST MINUTE ALERT terminal).
2.0 INDICATOR LIGHTS
The green POWER light on the timer shows that power is being supplied to the timer. The red LOAD light indicates that the timer
has been started and that the output to the load is currentl being timed.
3.0 RESET
The reset button resets the timer and cancels an existing time. Use a pen or similar object to press the recessed reset button.
4.0 COIN VERIFICATION
A horn connected to the LAST MINUTE ALERT terminal will also provide coin verification. When a coin is accepted, the timer will
beep the horn to acknowledge that a coin has been accepted. For electronic coin acceptors that give multiple pulses for a single
coin, the horn will beep for each pulse received.
5.0 POWER-UP/RESET STATUS
When power is applied to the timer or the timer is reset b pressing the reset button, the timer indicates that it is operating correctl
b sounding the Last Minute Alert horn and flashing the 1 Coin Restart light for 1 second (provided that either a horn or a light are
installed).
MAGIKTIMER
BAY & VACUUM
ELECTRONIC TIMER
Plus
Timers/MT580/instructions.qx
v1.2

WITH TRANSFORMER
WITHOUT TRANSFORMER
line
voltage
3A typical
NC NO COM
N/C
Selector Switc
24VAC (500mA max) Lig t
for 1 Coin Restart
12VDC (100mA max) Horn
for Last Minute Alert
yellow
black
blue
purple
000125 24VAC
counter
120 VAC
source
20A max
Mec anical
Coin Acceptor
w/Micro-Switc
NC NO COM
20A max
120VAC LOAD 120VAC LOAD
24VAC LOAD
24VAC LOAD
24VAC LOAD 24VAC LOAD
24VAC LOAD
24VAC LOAD
24VAC LOAD
1
2
3
4
5
+6
–7
8
9
10
11
LAST MIN
ALERT
24 VAC
HOT
COMMON
LOAD
(IN)
LOAD
(OUT)
COIN
SWITCH
COIN
SWITCH
COUNTER
+12VDC
OUT
1COIN
RESTART
120 VAC
HOT
T
IMER
MAGIK
Plus
MODEL MT580 1
2
3
4
5
+6
–7
8
9
10
11
LAST MIN
ALERT
24 VAC
HOT
COMMON
LOAD
(IN)
LOAD
(OUT)
COIN
SWITCH
COIN
SWITCH
COUNTER
+12VDC
OUT
1COIN
RESTART
120 VAC
HOT
T
IMER
MAGIK
Plus
MODEL MT580
1
2
3
4
5
+6
–7
8
9
10
11
LAST MIN
ALERT
24 VAC
HOT
COMMON
LOAD
(IN)
LOAD
(OUT)
COIN
SWITCH
COIN
SWITCH
COUNTER
+12VDC
OUT
1COIN
RESTART
120 VAC
HOT
T
IMER
MAGIK
Plus
MODEL MT580
BWG
NC NO COM
Electronic
Coin Acceptor
(CoinPro,
Slugbuster)
N/C
yellow
black
blue
purple
OR
Mec anical
Coin Acceptor
w/Micro-Switc
–
+
transformer
24
VAC
120
VAC
transformer
24
VAC
000125
120VAC
counter
120 VAC
source
BWG
000125
24VAC
counter
Electronic
Coin Acceptor
(CoinPro,
Slugbuster)
OR
Mec anical
Coin Acceptor
w/Micro-Switc
120VAC LOAD typically is vacuum motor(s).
24VAC LOADs typically consist of solenoids, motor starter, etc.
Load fuse must be installed.
Always turn power off before servicing any electrical system.
Back mounting plate of timer s ould be connected to eart ground.
Transformer must be Class 2 or fused on secondary.
Never connect 120VAC to terminal #2. Never connect any power to terminals #7, #10, OR #11.
All field installations must meet applicable codes.
•
•
•
•
•
•
•
•Timers/MT580/wiring.cad
v1.2
Terminals #10 (+12VDC OUT) and
#11 (LAST MIN ALERT) are not
available w en powering timer
wit 120 VAC.
120VAC LOAD
(TYPICAL VACUUM WIRING)
24VAC LOAD
(TYPICAL BAY CARWASH WIRING)
NOTES