Magnetrol ECHOTEL 940 User manual

®
Ultrasonic
Level
Switches
Installation and Operating Manual
ECHOTEL®940/941

Front view
of gap Wrench
flats are
aligned with
sensor gap
These units are in compliance with:
1.The EMC directive 2014/30/EU. The units have been
tested to EN 61326: 1997 + A1 + A2
2.The PED directive 2014/68/EU (pressure equipment
directive). Safety accessories per category IV module
H1.
2
UNPACKING
Unpack the instrument carefully. Make sure all components
have been removed from the foam protection. Inspect all
components for damage. Report any concealed damage to
the carrier within 24 hours. Check the contents of the car-
ton/crates against the packing slip and report any discrep-
ancies to Magnetrol. Check the nameplate model number to
be sure it agrees with the packing slip and purchase order.
Check and record the serial number for future reference
when ordering parts.
OUNTING
Tri-Clamp®
Gap indication
odel and
serial number
High alarm
High alarm
Low alarm
Filling line
Pump protection
Pump
Low alarm
Nozzle mounting: gap must be free
▼ ▼
min.
25 mm
Threaded Welded flange
0038

3
WIRING – RELAY VERSION: ECHOTEL 940
OUTPUT
Level Relay Wiring
De-energized
Energized
NO (Violet)
CO (Orange)
NC (Brown)
NO (Violet)
CO (Orange)
NC (Brown)
I PORTANT: When power is lost or gap is dry;
the relay de-energizes.
-
+
green
black
red
brown (NC)
orange (CO )
violet (NO)

4
WIRING – CURRENT SHIFT VERSION: ECHOTEL 941
OUTPUT
-
+
green
black
red
Level Current
8 mA (± 1 mA)
16 mA (± 1 mA)
Wet gap
Dry gap
▼
▼
mA
Normal operation

5
SPECIFICATIONS
PHYSICAL/FUNCTIONAL SPECIFICATIONS
PERFOR ANCE SPECIFICATIONS
TRANSDUCER SPECIFICATIONS
TE PERATURE/PRESSURE RATING
-40
(-40)
0
(32)
40
(100)
80
(176)
120
(250)
50 (725)
100 (1450)
150 (2175)
200 (2900)
bar (psi)
C
(F)
150
(300)
Process temperature
Process pressure
103 bar (transducer length > min. length)
138 bar (transducer length = min. length)
Description Specification
Response time 0,5 s typical
Repeatability ± 2 mm (0.078")
Ambient Temperature -40 °C up to +85 °C (-40 ° up to +185 ° )
Humidity 0-99 %, non condensing
Electromagnetic Compatibility Meets CE requirements (EN 61326: 1997 + A1 + A2)
Description Specification
Input voltage 12 - 35 V DC
Power consumption < 1 W
Signal output Current Shift 8 mA (± 1 mA) - dry gap or 16 mA (± 1 mA) - wet gap
Relay SPDT: 1 A @ 30 V DC
Potted cable 45 cm (18") flying leads of 18 AWG wires
Net Weight 510 g (unit with 3/4" NPT transducer and shortest length)
Description Specification
Material 316/316L SST (1.4401/1.4404)
Mounting Threaded (NPT/BSP) – langed (ANSI) – Hygienic (Tri-Clamp®)
Actuation length rom 3 cm up to 250 cm (1.2" up to 98.4")
Operating process temp. -40 °C up to +85 °C (-40 ° up to +185 ° )
Max pressure
103 bar @ +85 °C (1500 psi @ +185 ° ) - transducer length > min. length
138 bar @ +85 °C (2000 psi @ +185 ° ) - transducer length = min. length
langed models are downrated to the design pressure of the selected flange

6
ODEL IDENTIFICATION
A complete measuring system consists of:
1.One code for electronics and transducer
2.OPTION: Standard cable length is 45 cm (18"). Specify cable length separately when a longer cable is required.
3. OPTION: 052-7012-002: code for Echotel 941 cast aluminium housing with terminal block, 3/4" NPT cable entry, IP 65
052-7012-003: code for Echotel 940 cast aluminium housing with terminal block, 3/4" NPT cable entry, IP 65
9M 4complete code for Echotel 940/941
ACTUATION LENGTH – Specify per cm (0.39") increment
Total insertion length = actuation length + 6 mm (0.25")
00 3 Minimum 3 cm (1.2") – for all connections except BSP
00 5 Minimum 5 cm (2.0") – for 3/4" BSP (G 3/4")
00 6 Minimum 6 cm (2.4") – for 1" BSP (G 1")
25 0 Maximum 250 cm (98.4")
PROCESS CONNECTION
Threaded
11 M 3/4" NPT
12 M 3/4" BSP (G 3/4")
22 M 1" BSP (G 1")
ANSI Flanges
23 M 1" 150 lbs ANSI R
33 M 1 1/2" 150 lbs ANSI R
43 M 2" 150 lbs ANSI R
Hygienic
3T M 1 1/2" Tri-Clamp®
4T M 2" Tri-Clamp®
BASIC MODEL NUMBER
940–N Echotel®940 OEM switch with integrated 1 A SPDT relay
941–N Echotel®941 OEM switch with current shift output 8/16 mA
X = product with a specific customer requirement

7
DI ENSIONS IN mm (inches)
Tri-Clamp®
Cast aluminium housing
Threaded NPT
Welded ANSI flange
3/4" NPT
3/4" NPT
3/4" NPT
cable entry
3/4" NPT
6 (0.25)
6 (0.25)
6 (0.25)
Ø 22,9 (0.90)
Ø 22,9 (0.90)
Ø 22,9 (0.90)
99 (3.9)
99 (3.9)
105 (4.13)
Actuation length
Actuation length
Threaded BSP
3/4" NPT
6 (0.25)
Ø 22,9 (0.90)
65 (2.56)
Actuation length
Actuation length
84 (3.31)
89
(3.50)
84 (3.31)

I PORTANT
SERVICE POLICY
Owners of Magnetrol products may request the return of a control; or, any part of a control for complete rebuilding or
replacement. They will be rebuilt or replaced promptly. Magnetrol International will repair or replace the control, at no cost to
the purchaser, (or owner) other than transportation cost if:
a. Returned within the warranty period; and,
b. The factory inspection finds the cause of the malfunction to be defective material or workmanship.
If the trouble is the result of conditions beyond our control; or, is NOT covered by the warranty, there will be charges for labour
and the parts required to rebuild or replace the equipment.
In some cases, it may be expedient to ship replacement parts; or, in extreme cases a complete new control, to replace the
original equipment before it is returned. If this is desired, notify the factory of both the model and serial numbers of the
control to be replaced. In such cases, credit for the materials returned, will be determined on the basis of the applicability of
our warranty.
No claims for misapplication, labour, direct or consequential damage will be allowed.
RETURNED ATERIAL PROCEDURE
So that we may efficiently process any materials that are returned, it is essential that a “Return Material Authorisation” (RMA)
form will be obtained from the factory. It is mandatory that this form will be attached to each material returned. This form is
available through Magnetrol’s local representative or by contacting the factory. Please supply the following information:
1. Purchaser Name
2. Description of Material
3. Serial Number and Ref Number
4. Desired Action
5. Reason for Return
6. Process details
Any unit that was used in a process must be properly cleaned in accordance with the proper health and safety standards
applicable by the owner, before it is returned to the factory.
A material Safety Data Sheet (MSDS) must be attached at the outside of the transport crate or box.
All shipments returned to the factory must be by prepaid transportation. Magnetrol will not accept collect shipments.
All replacements will be shipped Ex Works.
www.magnetrol.com
BENELUX Heikensstraat 6, 9240 Zele, België -Belgique
FRANCE Tel. [phone] • Fax. [phone] • E-Mail: [email protected]
DEUTSCHLAND Alte Ziegelei 2-4, D-51491 Overath
Tel. [phone] / 9536-0 • Fax. [phone] / 9536-53 • E-Mail: [email protected]
INDIA B-506, Sagar Tech Plaza, Saki Naka Junction, Andheri (E), Mumbai - 400072
Tel. [phone] • Fax. [phone] • E-Mail: [email protected]
ITALIA Via Arese 12, I-20159 Milano
Tel. [phone] • Fax. [phone] • E-Mail: [email protected]
RUSSIA Business center “Farvater”, Ruzovskaya Street 8B, office 400A, 190013 St. Petersburg
Tel. [phone] • E-Mail: [email protected]
U.A.E. PO Box 261454 • JAFZA LIU FZS1 – BA03, Jebel Ali
Tel. [phone] • Fax [phone] • E-Mail: [email protected]
UNITED Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL
KINGDOM
Tel. [phone] • Fax [phone] • E-Mail: [email protected]
BULLETIN N°: BE 51-647.6
E ECTIVE: AUGUST 2017
SUPERSEDES: September 2014
UNDER RESERVE O MODI ICATIONS