Makita BFL060F User manual

1
GB Cordless Angle Screwdriver INSTRUCTION MANUAL
UA
Бездротовий кутовий шуруповерт ІНСТРУКЦІЯ ЗЕКСПЛУАТАЦІЇ
PL Bezprzewodowa wkrętarka kątowa INSTRUKCJA OBSŁUGI
RO
Maşinăde înşurubat unghiularăcu acumulator MANUAL DE INSTRUCŢIUNI
DE Akku-Winkelschrauber BEDIENUNGSANLEITUNG
HU
Akkumulátoros könyökös csavarbehajtó HASZNÁLATI KÉZIKÖNYV
SK Akumulátorový uhlový skrutkovačNÁVOD NA OBSLUHU
CZ Akumulátorový úhlový šroubovák NÁVOD K OBSLUZE
BFL060F
BFL080F
BFL081F
BFL120F
BFL121F
BFL200F

2
1
1 003615
1
2 003616
1
3 003617
1
A
B
4 003618
2
1
5 003619 6 003621
1
2
3
48
5
6
7
7 003622
1
2
3
8 003623
1
2
9 004170
1
10 001145
1
2
11 003628

3
ENGLISH
Explanation of general view
1-1. Battery cartridge
2-1. Battery cartridge
3-1. Switch trigger
4-1. Reversing switch lever
5-1. Light
5-2. LED indicator
7-1. Angle head
7-2. Adjusting ring
7-3. Ring
7-4. Scale
7-5. Adjusting grip
7-6. Hole for Adjusting grip
7-7. Edge of Adjusting ring
7-8. Compression spring
8-1. Socket
8-2. Hole
8-3. Pin
9-1. Screw bit
9-2. Sleeve
10-1. Limit mark
11-1. Screwdriver
11-2. Brush holder cap
SPECIFICATIONS
Model BFL060F BFL080F BFL120F BFL081F BFL121F BFL200F
Hard joint 1.5 - 6 N • m 2 - 8 N • m 5 - 12 N • m 2 - 8 N • m 5 - 12 N • m 8 - 20 N • m
Fastening
torque Soft joint 1.5 - 6 N • m 2 - 7.5 N • m 5 - 12 N • m 2 - 7.5 N • m 5 - 11.5 N • m 8 - 18 N • m
Square drive 9.5 mm 9.5 mm 9.5 mm 9.5 mm 9.5 mm 9.5 mm
No load speed (min-1) 450 450 250 700 410 220
430 x 65 x 74 mm (With Battery Cartridge BH9020A)
430 x 71 x 92 mm (With Battery Cartridge BH1220)
413 X 74 X 92 mm (With Battery Cartridge BH1220C)
Dimensions
454 x 65 x 74 mm (With Battery Cartridge BH9033A)
454 x 71 x 92 mm (With Battery Cartridge BH1233)
421 x 74 x 107 mm (With Battery Cartridge BH1233C)
1.5 kg (With Battery Cartridge BH9020A) 1.7 kg (With Battery Cartridge BH1220)
1.6 kg (With Battery Cartridge BH1220C)
Net weight
1.7 kg (With Battery Cartridge BH9033A) 2.0 kg (With Battery Cartridge BH1233)
1.9 kg (With Battery Cartridge BH1233C)
Rated voltage D.C. 9.6 V D.C. 12 V
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
ENE033-1
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
ENG001-1
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is not more
than 70 dB (A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s2.
ENH002-4
Model; BFL060F,BFL080F,BFL081F,BFL120F,
BFL121F,BFL200F
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN50260, EN55014 in accordance with Council
Directives, 89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki CE2005
000087
Director
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
ENC002-3
IMPORTANT SAFETY
INSTRUCTIONS FOR CHARGER
& BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS- This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
3. CAUTION - To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may

4
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when
disconnecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise
subjected to damage or stress.
8. Do not operate charger with damaged cord or
plug - replace them immediately.
9. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman.
10. Do not disassemble charger or battery
cartridge; take it to a qualified serviceman
when service or repair is required. Incorrect
reassembly may result in a risk of electric
shock or fire.
11. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to
ensure that they do not play with the battery
charger.
14. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
15. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY
CARTRIDGE
1. Do not charge battery cartridge when
temperature is BELOW 10 ﾟC (50 ﾟF) or
ABOVE 40 ﾟC (104 ﾟF).
2. Do not attempt to use a step-up transformer,
an engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
4. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
5. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟC(122 ﾟF).
6. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
7. Be careful not to drop, shake or strike battery.
8. Do not charge inside a box or container of any
kind. The battery must be placed in a well
ventilated area during charging.
ENB026-1
ADDITIONAL SAFETY RULES
FOR TOOL
1. Be aware that this tool is always in an
operating condition, because it does not have
to be plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will also make exposed metal parts of the tool
"live" and shock the operator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
SAVE THESE INSTRUCTIONS.

5
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Fig.1
Fig.2
• Always switch off the tool before insertion or
removal of the battery cartridge.
For Models BFL060F,BFL080F, BFL120F
• To remove the battery cartridge, withdraw it from
the tool while pressing the buttons on both sides of
the cartridge.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to
you or someone around you.
• Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
For Models BFL081F, BFL121F, BFL200F
• To remove the battery cartridge, withdraw it from
the tool while sliding the button on the front of the
cartridge.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can
see the red part on the upper side of the button, it
is not locked completely. Insert it fully until the red
part cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone
around you.
• Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Charging
Before using battery charger, read all instructions and
cautionary markings on the battery charger.
BH9020A (Ni-MH) 2000 8 Approx. 30 min.
BH9033 (Ni-MH) 3300 8 Approx. 50 min.
BH9033A (Ni-MH) 3300 8 Approx. 50 min.
BH1220/BH1220C (Ni-MH) 2000 10 Approx. 30 min.
BH1233/BH1233C (Ni-MH) 3300 10 Approx. 50 min.
Battery type Capacity
(mAh)
Number of
cells Charging time*
006400
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10°C - 40°C (50°F - 104°F).
Let a hot battery cartridge cool down before
charging it.
4. Charge the Nickel Metal Hydride battery cartridge
when you do not use it for more than six months.
5. Always stop tool operation and charge the battery
cartridge when you notice that the warning lamp
lightened up.
Refresh charging
• Refreshing battery adapter (optional accessory)
can refresh an inactive battery cartridge.
• Refresh charging should be done once a week.
• When you charge a new battery cartridge or a
battery cartridge that has not been used for a long
time, it may not accept a full charge. In this case,
refresh charging must be done. The battery
cartridge may decrease the tool performance,
because the chemical substance of the battery
cartridge is inactive.
Checking the remaining battery capacity
For BH9020A,BH9033A
Indicating lamp
(C) EF
Capacity
80% - 100%
60% - 80%
40% - 60%
10% - 40%
0% - 10%
Indicating lamp
Capacity
80% - 100%
60% - 80%
40% - 60%
10% - 40%
0% - 10%
EF
orange
orange
001254
When charging
When the charging begins, the first (far left) indicating
lamp begins to flicker. Then, as charging proceeds, the
other lamps light, one after the other, to indicate the
battery capacity.
When using
When the tool is switched on, the lamps will light to
indicate the remaining battery capacity. When the tool is
switched off, the light goes out. If the battery has not
been used for a long time, or is needed refresh charging,
the orange lamp begins to flicker. Use Makita refreshing
adapter to refresh the battery.

6
CAUTION:
• A battery cartridge extracted from the charger that
has been unplugged with the battery cartridge
inserted does not indicate the battery capacity due
to its protective function even if the tool is switched
on after the battery insertion into the tool. At this
time, recharge it for about five seconds before use.
NOTE:
• Please contact Makita Authorized or Factory
Service Center if the warning lamp of the battery
cartridge does not light up when using or charging.
Switch action
Fig.3
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF" position
when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Reversing switch action
Fig.4
CAUTION:
• Always check the direction of rotation before
operation.
• Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
• When not operating the tool, always set the
reversing switch lever to the neutral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the lamps
Fig.5
CAUTION:
• Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
LED indicator / Beeper
Led indicator / Beeper on the tool shows the following
functions.

7
LED indicator Beeper
Auto-stop fastening
This function works when the tool has reached
the preset fastening torque andnormal
tightening has been completed. This helps
overtightening to be avoided.
Delayedre-start
For approximately one secondafter auto-stop
fastening, the tool does not start even if the
switch trigger is pulled.
Warning against
insufficient fastening
Insufficient fastening has been performed
when the switch trigger has releasedbefore
reaching the preset fastening torque.
Lights up in red. A long beep
Lights up in red. A long beep
Retighten the
screw
Warning for battery
cartridge capacity
This indicates the appropriate time to replace
the battery cartridge when the battery power
becomes low.
Flickers in redslowly. A series of long
beeps
Flickers in redquickly. A series of short
beeps
A series of short
beeps
Replace the battery
with fully charged
one
Replace the battery
with fully charged
one
Replace the battery
with fully charged
one
Checking the
remaining battery
capacity, Autostop
This function works when the battery power
is almost usedup. At this time, tool stops
immediately.
Check the LED
indicator, light and
beeper operation
This function works to check the proper
operation of the LED indicator, light and
beeper when a battery cartridge has been
insertedinto the tool.
Lights up first in green,
next red.
(Andthen the light
comes on.)
A series of very
short beeps
-
Anti-reset of
controller
This function works when an abnormal drop
of the battery voltage occurs for some reason,
andthe tool stops.
Flickers in redand
green alternatively.
A series of short
beeps
Overheat
This function works when the temperature
of the controller goes up very highly,
andthe tool stops.
Remove the battery
cartridge immediately
andcool the tool
down.
Operation error of
the switch trigger
This function works to avoidthe tool's
immediate start upon insertion of battery
cartridge into the tool with the switch trigger
being pulled.
Flickers in redand
green alternatively.
Release the switch
trigger.
Function Status Action to be taken
Lights up in green for
approximately one
second.
--
Status of the LED indicator/beeper
006388
Adjusting the fastening torque
Fig.6
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjusting
the fastening torque as follows.
1. First remove the battery cartridge from the tool.
2. Loosen the screws securing the light cover.
3. Rotate the ring in the front of the tool by hand so
that a hole can be seen below the ring.

8
4. Place the battery cartridge in place and pull the
switch trigger. Release it so that the adjusting ring
rotates and becomes visible in the hole. And then
remove the battery cartridge.
Fig.7
5. Use an optional adjusting grip to adjust the
fastening torque. Insert the pin of the adjusting
grip into the hole in the front of the tool. And then,
turn the adjusting grip clockwise to set a greater
fastening torque, and counterclockwise to set a
smaller fastening torque.
6. Align the edge of the adjusting ring with your
desired number on the fastening torque scale.
7. Insert the battery cartridge and be sure that a
fastening torque has been set up by using a
fastening torque tester.
8. Tighten the screws to secure the light cover and
then rotate the ring in front of the tool until the ring
is locked.
NOTE:
• Numbers on the fastening torque scale is a
guideline to set up your desired fastening torque.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Selecting correct socket or screw bit
There are different types of sockets or bits for some
models depending on applications. Choose and install a
correct socket or bit for your application.
Installing or removing socket
Fig.8
To install the socket, push it onto the square drive of the
tool with one hand by depressing a pin on the square
drive with another hand until it locks into place. To
remove the socket, simply pull it off depressing the pin
on the square drive.
Installing or removing bit
Fig.9
For tools with retracting sleeve
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will go.
Then release the sleeve to secure the bit.
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
For tools without retracting sleeve
To install the bit, just insert the bit into the spindle as far
as it will go. To remove the bit, pull the bit out firmly.
OPERATION
Hold the tool firmly and place the socket over the bolt or
nut. Then switch the tool on. When the clutch cuts in, the
motor will stop automatically. Then release the switch
trigger.
NOTE:
• Hold the tool with its square drive pointed straight
at the bolt or nut, or the bolt or nut will be
damaged.
Limits of fastening capacity
Use the tool within the limits of fastening capacity. If you
use the tool beyond the limits, the clutch does not work.
And the tool cannot deliver enough fastening torque.
Range of fastening capacity
Revolution angle( )
360
300
240
180
120
60
0
1.52 3 4
N m
56
BFL060F
.
Torque
008231
Range of fastening capacity
Torque
Revolution angle( )
N m
360
300
240
180
120
60
0234 5678
BFL080F
.
003624
BFL081F
Range of fastening capacity
Revolution angle ( )
Torque N m
.
005026

9
Range of fastening capacity
Torque
Revolution angle( )
360
300
240
180
120
60
05678
N m
9101112
BFL120F
.
003625
Range of fastening capacity
Torque
Revolution angle( )
360
300
240
180
120
60
05678
N m
9101112
BFL121F
.
003626
Range of fastening capacity
Torque
Revolution angle( )
N m
360
300
240
180
120
60
08101214
1618 20
BFL200F
.
003627
NOTE:
• The revolution angle means the angle which a
screw/bolt revolves when the tool attains to 100%
from 50% of desired torque.
• Use of a low temperature conditioned battery
cartridge may sometimes give warning for battery
cartridge capacity by warning lamp and beeper
which makes the tool stop immediately. In this case,
the range of fastening capacity may be inferior to
those shown in the above even if a charged battery
cartridge is used.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
Replacing carbon brushes
Fig.10
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
Fig.11
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Protector
• Battery charger DC14SA
• Ni-MH Battery Cartridge BH9020A/9033A
• Ni-MH Battery Cartridge
BH1220/BH1220C/BH1233/BH1233C
• Automatic refreshing adapter
• Angle head set

10
УКРАЇНСЬКА
Пояснення до загального виду
1-1. Касета закумулятором
2-1. Касета закумулятором
3-1. Кнопка вимикача
4-1. Важіль перемикача реверсу
5-1. Підсвічування
5-2. РК індикатор
7-1. Кутова голівка
7-2. Кільце регулювання
7-3. Кільце
7-4. Масштаб
7-5. ручка регулювання
7-6. Отвір для регулювання ручки
7-7. Край кільця регулювання
7-8. Натискна пружина
8-1. Ключ
8-2. Отвір
8-3. Штифт
9-1. Наконечник-викрутка
9-2. Муфта
10-1. Обмежувальна відмітка
11-1. Викрутка
11-2. Ковпачок щіткотримача
ТЕХНІЧНІ ХАРАКТЕРИСТИКИ
Модель BFL060F BFL080F BFL120F BFL081F BFL121F BFL200F
Жорстке з'єднання 1,5 - 6 Н• м2 - 8 Н• м5 - 12 Н• м2 - 8 Н• м5 - 12 Н• м8 - 20 Н• м
Момент
затягування
М'яке з'єднання 1,5 - 6 Н• м2 - 7,5 Н• м5 - 12 Н• м2 - 7,5 Н• м5 - 11,5 Н• м8 - 18 Н• м
Квадратна викрутка 9,5 мм 9,5 мм 9,5 мм 9,5 мм 9,5 мм 9,5 мм
Швидкість холостого ходу (хв
-1
) 450 450 250 700 410 220
430 x 65 x 74 мм (зкасетою закумулятором BH9020A) 430 x 71 x 92 мм
(зкасетою закумулятором BH1220)
413 X 74 X 92 мм (зкасетою закумулятором BH1220C)
Габарити
454 x 65 x 74 мм (зкасетою закумулятором BH9033A) 454 x 71 x 92 мм
(зкасетою закумулятором BH1233)
421 x 74 x 107 мм (зкасетою закумулятором BH1233C)
1,5 кг (зкасетою закумулятором BH9020A) 1,7 кг (зкасетою закумулятором BH1220)
1,6 кг (зкасетою закумулятором BH1220C)
Чиста вага
1,7 кг (зкасетою закумулятором BH9033A) 2,0 кг (зкасетою закумулятором BH1233)
1,9 кг (зкасетою закумулятором BH1233C)
Номінальна напруга 9,6 Впост. Тока 12 Впост. Тока
• Через те, що ми не припиняємо програми досліджень ірозвитку, наведені тут технічні характеристики можуть бути змінені
без попередження.
• Примітка. Урізних країнах технічні характеристики можуть бути різними.
ENE033-1
Призначення
Інструмент призначено для укручування гвинтів у
деревину, пластмасу та метал.
ENG001-1
Для Європейських країн тільки
шум та вібрація
Рівень шуму за шкалою Аутиповому виконанні
становить макс. 70 дБ (A).
Рівень шуму під час роботи може перевищувати 85
дБ (A).
Користуйтеся засобами захисту слуху.
Типове зважене середньоквадратичне прискорення
не перевищує 2,5 м/с2.
ENH002-4
Модель; BFL060F,BFL080F,BFL081F,BFL120F,
BFL121F,BFL200F
ДЕКЛАРАЦІЯ ВІДПОВІДНОСТІ ЄС
Ми заявляємо під нашу виключну відповідальність,
що цей виріб відповідає вимогам наведених нижче
стандартів нормативної документації;
EN50260, EN55014 згідно зКерівними Інструкціями
Ради, 89/336/EEC, 98/37/EC.
Ясухіко Канзакі CE2005
000087
Директор
МАКІТА ІНТЕРНЕШНЛ ЮРОП ЛТД.
Мічіган-Драйв, Тонгвелл, Мілтон-Кейнес, графство
Бекінгемшир MK15 8JD, АНГЛІЯ
Відповідальний виробник:
Макіта Корпорейшн Анджо Аічі Японія
ENC002-3
ВАЖЛИВІ ІНСТРУКЦІЇ З
БЕЗПЕКИ ДЛЯ ЗАРЯДНОГО
ПРИСТРОЮ ТА КАСЕТИ З
БАТАРЕЄЮ
1. ЗБЕРЕЖІТЬ ЦЮ ІНСТРУКЦІЮ – вона містить
важливі вказівки зтехніки безпеки іроботи
ззарядним пристроєм акумулятора.
2. Перед тим як користуватися касетою з
батареєю, слід прочитати усі інструкції та
попереджуючі відмітки про (1) зарядний
пристрій, (2) акумулятор та (3) вироби, що