Makita DSL801 User manual

DSL801
EN Cordless Drywall Sander INSTRUCTION MANUAL 8
ZHCN 充电式石膏板砂光机 使用说明书 21
ID Mesin Ampelas Papan Gips
Nirkabel PETUNJUK PENGGUNAAN 34
MS Pelelas Dinding Kering Tanpa
Kord MANUAL ARAHAN 48
VI Máy Chà Nhám Tường Cầm
Tay Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 62
TH   75

12
3
Fig.1
1
2
Fig.2
1
AB
Fig.3
1
2
3
Fig.4
1
Fig.5
1
Fig.6
1
2
Fig.7
21
Fig.8
2

1
Fig.9
1
2
3
Fig.10
1 2
3
Fig.11
1
2
3
4
5
Fig.12
Fig.13
3

1
Fig.14
1
2
Fig.15
12
Fig.16
Fig.17
Fig.18
Fig.19
4

1
Fig.20
1
2
3
4
Fig.21
1
2
3
Fig.22
1
Fig.23
12
21
Fig.24
Fig.25
5

1
Fig.26
21
Fig.27
1
Fig.28
1
Fig.29
12
21
Fig.30
12
Fig.31
6

13
2
Fig.32
7

8ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DSL801
Paper size 225 mm
Pad diameter 210 mm
No load speed 1,000 - 1,800 min-1
Dimensions (L x W x H) 1,120 mm - 1,540 mm x 278 mm x 273 mm
Rated voltage D.C. 18 V
Net weight 4.6 - 5.8 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
withoutnotice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Batterycartridge BL1815N/BL1820B/BL1830B/BL1840B/BL1850B/BL1860B
Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF/
DC18SH
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Symbols
Thefollowingsshowthesymbolswhichmaybeused
fortheequipment.Besurethatyouunderstandtheir
meaningbeforeuse.
Readinstructionmanual.
Wearsafetyglasses.
Ni-MH
Li-ion
OnlyforEUcountries
Duetothepresenceofhazardouscom-
ponentsintheequipment,wasteelectrical
andelectronicequipment,accumulators
andbatteriesmayhaveanegativeimpact
ontheenvironmentandhumanhealth.
Donotdisposeofelectricalandelectronic
appliancesorbatterieswithhousehold
waste!
InaccordancewiththeEuropeanDirective
onwasteelectricalandelectronicequip-
mentandonaccumulatorsandbatteries
andwasteaccumulatorsandbatteries,
as well as their adaptation to national law,
wasteelectricalequipment,batteriesand
accumulatorsshouldbestoredseparately
anddeliveredtoaseparatecollectionpoint
formunicipalwaste,operatinginaccor-
dancewiththeregulationsonenvironmen-
talprotection.
Thisisindicatedbythesymbolofthe
crossed-outwheeledbinplacedonthe
equipment.
Intended use
Thetoolisintendedforsandingdrywallorceiling.

9ENGLISH
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm“powertool”inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless)powertool.
Work area safety
1. Keep work area clean and well lit.Clutteredor
darkareasinviteaccidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust.Powertoolscreatesparks
whichmayignitethedustorfumes.
3. Keep children and bystanders away while
operating a power tool.Distractionscancause
youtolosecontrol.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduceriskofelectricshock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.Thereisanincreasedriskofelec-
tricshockifyourbodyisearthedorgrounded.
3. Do not expose power tools to rain or wet con-
ditions.Waterenteringapowertoolwillincrease
theriskofelectricshock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.Damagedorentangledcords
increasetheriskofelectricshock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use.Useof
acordsuitableforoutdoorusereducestheriskof
electricshock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.UseofanRCDreduces
theriskofelectricshock.
7. Power tools can produce electromagnetic
elds (EMF) that are not harmful to the user.
However,usersofpacemakersandothersimilar
medicaldevicesshouldcontactthemakeroftheir
deviceand/ordoctorforadvicebeforeoperating
this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication.Amomentofinattentionwhileoperating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection.Protectiveequipmentsuch
asadustmask,non-skidsafetyshoes,hardhator
hearingprotectionusedforappropriateconditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.Carryingpowertoolswith
yourngerontheswitchorenergisingpowertools
thathavetheswitchoninvitesaccidents.
4. Remove any adjusting key or wrench before
turning the power tool on.Awrenchorakeyleft
attachedtoarotatingpartofthepowertoolmay
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times.Thisenablesbettercontrol
ofthepowertoolinunexpectedsituations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
longhaircanbecaughtinmovingparts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.Useof
dustcollectioncanreducedust-relatedhazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.Acarelessaction
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.

10 ENGLISH
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application.Thecorrect
powertoolwilldothejobbetterandsaferatthe
rateforwhichitwasdesigned.
2. Do not use the power tool if the switch does
not turn it on and o󰀨.Anypowertoolthatcannot
becontrolledwiththeswitchisdangerousand
mustberepaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools.Suchpreventivesafetymeasuresreduce
theriskofstartingthepowertoolaccidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.Powertoolsaredangerousinthe
handsofuntrainedusers.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Manyaccidentsarecausedbypoorlymaintained
power tools.
6. Keep cutting tools sharp and clean.Properly
maintainedcuttingtoolswithsharpcuttingedges
arelesslikelytobindandareeasiertocontrol.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.Useofthepowertool
foroperationsdi󰀨erentfromthoseintendedcould
resultinahazardoussituation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease.Slippery
handlesandgraspingsurfacesdonotallowfor
safehandlingandcontrolofthetoolinunexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled.Theentangle-
mentofclothworkglovesinthemovingpartsmay
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer.Achargerthatissuitablefor
onetypeofbatterypackmaycreateariskofre
whenusedwithanotherbatterypack.
2. Use power tools only with specically desig-
nated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatterytermi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritationorburns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
mayexhibitunpredictablebehaviourresultingin
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
peratureabove130°Cmaycauseexplosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions.Chargingimproperlyorattemperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts.Thiswillensurethatthesafetyofthepower
tool is maintained.
2. Never service damaged battery packs.Service
ofbatterypacksshouldonlybeperformedbythe
manufacturerorauthorizedserviceproviders.
3. Follow instruction for lubricating and chang-
ing accessories.
Cordless drywall sander safety
warnings
Safety Warnings Common for Sanding Operations:
1. This power tool is intended to function as a
sander. Read all safety warnings, instructions,
illustrations and specications provided with
this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/
orseriousinjury.
2. Operations such as grinding, wire brush-
ing, polishing or cutting-o󰀨 are not recom-
mended to be performed with this power tool.
Operationsforwhichthepowertoolwasnot
designedmaycreateahazardandcauseper-
sonalinjury.
3. Do not use accessories which are not speci-
cally designed and recommended by the tool
manufacturer.Justbecausetheaccessorycan
beattachedtoyourpowertool,itdoesnotassure
safeoperation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.Accessoriesrunningfasterthan
theirratedspeedcanbreakandyapart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool.Incorrectlysizedaccessories
cannotbeadequatelyguardedorcontrolled.
6. Do not use a damaged accessory. Before each
use inspect the accessory such as pad for
cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of
the rotating accessory and run the power tool
at maximum no-load speed for one minute.
Damagedaccessorieswillnormallybreakapart
duringthistesttime.

11 ENGLISH
7. Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appro-
priate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.
Theeyeprotectionmustbecapableofstopping
yingdebrisgeneratedbyvariousoperations.
Thedustmaskorrespiratormustbecapableof
ltratingparticlesgeneratedbyyouroperation.
Prolongedexposuretohighintensitynoisemay
causehearingloss.
8. Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragmentsofworkpieceorofabrokenaccessory
mayyawayandcauseinjurybeyondimmediate
areaofoperation.
9. Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring.Contactwitha“live”wirewillalsomake
exposedmetalpartsofthepowertool“live”and
couldgivetheoperatoranelectricshock.
10. Position the cord clear of the spinning acces-
sory.Ifyoulosecontrol,thecordmaybecutor
snaggedandyourhandorarmmaybepulledinto
thespinningaccessory.
11. Never lay the power tool down until the acces-
sory has come to a complete stop.Thespinning
accessorymaygrabthesurfaceandpullthe
powertooloutofyourcontrol.
12. Do not run the power tool while carrying it at
your side.Accidentalcontactwiththespinning
accessorycouldsnagyourclothing,pullingthe
accessoryintoyourbody.
13. Do not operate the power tool near ammable
materials.Sparkscouldignitethesematerials.
14. Do not use accessories that require liquid
coolants.Usingwaterorotherliquidcoolants
mayresultinelectrocutionorshock.
Kickback and Related Warnings
Kickbackisasuddenreactiontoapinchedorsnagged
rotatingpadoranyotheraccessory.Pinchingorsnag-
gingcausesrapidstallingoftherotatingaccessory
whichinturncausestheuncontrolledpowertooltobe
forcedinthedirectionoppositeoftheaccessory’srota-
tionatthepointofthebinding.
Forexample,ifapadissnaggedorpinchedbythe
workpiece,theedgeofthepadthatisenteringintothe
pinchpointcandigintothesurfaceofthematerialcaus-
ingthepadtoclimboutorkickout.Thepadmayeither
jumptowardorawayfromtheoperator,dependingon
directionofthepad’smovementatthepointofpinching.
Padmayalsobreakundertheseconditions.
Kickbackistheresultofpowertoolmisuseand/or
incorrectoperatingproceduresorconditionsandcanbe
avoidedbytakingproperprecautionsasgivenbelow.
1. Maintain a rm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
Theoperatorcancontroltorquereactionsorkick-
backforces,ifproperprecautionsaretaken.
2. Never place your hand near the rotating acces-
sory.Accessorymaykickbackoveryourhand.
3. Do not position your body in the area where
power tool will move if kickback occurs.
Kickbackwillpropelthetoolindirectionopposite
tothewheel’smovementatthepointofsnagging.
4. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.Corners,sharpedgesorbouncing
haveatendencytosnagtherotatingaccessory
andcauselossofcontrolorkickback.
5. Do not attach a saw chain woodcarving blade
or toothed saw blade.Suchbladescreatefre-
quentkickbackandlossofcontrol.
Safety Warnings Specic for Sanding Operations:
1. Do not use excessively oversized sanding
disc paper. Follow manufacturers recommen-
dations, when selecting sanding paper. Larger
sandingpaperextendingbeyondthesanding
padpresentsalacerationhazardandmaycause
snagging,tearingofthediscorkickback.
Additional Safety Warnings:
1. Do not leave the tool running. Operate the tool
only when hand-held.
2. Check that the workpiece is properly
supported.
3. Pay attention that the pad continues to rotate
after the tool is switched o󰀨.
4. If working place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
5. Do not use the tool on any materials contain-
ing asbestos.
6. Do not use cloth work gloves during operation.
Fibersfromclothglovesmayenterthetool,which
causestoolbreakage.
7. Always work in well ventilated area.
8. When placing the tool, place it on a at and
stable surface.
9. When operating the tool, connect the tool to a
vacuum cleaner as much as possible to keep
the working area clean and prevent the oper-
ator from inhaling particles generated by the
operation.
10. Handle and store accessories with care.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.

12 ENGLISH
2. Do not disassemble or tamper with the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge.Suchconductmayresultina
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwardingagents,specialrequirementonpack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
inganexpertforhazardousmaterialisrequired.
Pleasealsoobservepossiblymoredetailed
nationalregulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
aroundinthepackaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita.Installingthebatteriesto
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge.Itmayresultinpoorperformanceor
breakdownofthetoolorbatterycartridge.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines.Itmayresultinamalfunctionor
breakdownofthetoolorbatterycartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wire-
less unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3. Use the wireless unit only with Makita tools.
4. Do not expose the wireless unit to rain or wet
conditions.
5. Do not use the wireless unit in places where
the temperature exceeds 50 °C (122 °F).
6. Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are nearby.
7. Do not operate the wireless unit in places
where automated devices are nearby.Ifoper-
ated,automateddevicesmaydevelopmalfunction
or error.
8. Do not operate the wireless unit in places
under high temperature or places where
static electricity or electrical noise could be
generated.

13 ENGLISH
9. The wireless unit can produce electromagnetic
elds (EMF) but they are not harmful to the
user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doingsomaycauseamalfunctionofthewireless
unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged.Water,dust,anddirtcomeintotheslotmay
causemalfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary.Restorethelidifitcomeso󰀨
fromthetool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipo󰀨yourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
►Fig.1: 1.Redindicator2.Button3.Batterycartridge
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoras
showninthegure,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen.Ifnot,
itmayaccidentallyfalloutofthetool,causinginjuryto
youorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.2: 1.Indicatorlamps2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
lightupforafewseconds.

14 ENGLISH
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE:Dependingontheconditionsofuseandthe
ambienttemperature,theindicationmaydi󰀨erslightly
fromtheactualcapacity.
NOTE:Therst(farleft)indicatorlampwillblinkwhen
thebatteryprotectionsystemworks.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutso󰀨powertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placedunderoneofthefollowingconditions:
Overload protection
Whenthetoolorbatteryisoperatedinamannerthat
causesittodrawanabnormallyhighcurrent,thetool
automaticallystopsandthelampblinks.Inthissit-
uation,turnthetoolo󰀨andstoptheapplicationthat
causedthetooltobecomeoverloaded.Thenturnthe
tool on to restart.
Overheat protection
Whenthetoolorbatteryisoverheated,thetoolstops
automaticallyandthelamplightsup.Inthiscase,letthe
toolandbatterycoolbeforeturningthetoolonagain.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automatically.Inthiscase,removethebatteryfromthe
toolandchargethebattery.
Switch action
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
CAUTION: Switch can be locked in “ON” posi-
tion for ease of operator comfort during extended
use. Apply caution when locking tool in “ON”
position and maintain rm grasp on tool.
CAUTION: Do not install the battery cartridge
with the lock button engaged.
CAUTION: When not operating the tool,
depress the trigger-lock button from side to
lock the switch trigger in the OFF position.
►Fig.3: 1.Trigger-lockbutton
►Fig.4: 1.Switchtrigger2.Lockbutton3.Trigger-
lockbutton
Topreventtheswitchtriggerfromaccidentallypulled,
thetrigger-lockbuttonisprovided.Tostartthetool,
depressthetrigger-lockbuttonfromA( )sideandpull
theswitchtrigger.Releasetheswitchtriggertostop.
Afteruse,depressthetrigger-lockbuttonfromB( )
side.
Forcontinuousoperation,depressthelockbuttonwhile
pullingtheswitchtrigger,andthenreleasetheswitch
trigger.Tostopthetool,pulltheswitchtriggerfully,then
release it.
Speed adjusting dial
►Fig.5: 1.Speedadjustingdial
Therotationspeedofthetoolcanbechangedbyturn-
ingthespeedadjustingdial.Thetablebelowshows
thenumberonthedialandthecorrespondingrotation
speed.
Number Speed
11,000 min-1
21,200 min-1
31,400 min-1
41,600 min-1
51,800 min-1
NOTICE: The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1, or the speed adjusting function may no
longer work.
Overload and overheat indicator
lamp
►Fig.6: 1.Indicatorlamp
Ifthetoolisoperatedwithexcessiveload,thetoolstops
automaticallyandtheindicatorlampblinksinred.Inthis
case,reducetheloadonthetool.
Ifthetoolisoverheated,thetoolstopsautomatically
andtheindicatorlamplightsupinred.Inthiscase,let
thetoolcooldownbeforeturningthetoolonagain.

15 ENGLISH
Electronic function
Thetoolsequippedwithelectronicfunctionareeasyto
operatebecauseofthefollowingfeatures.
Constant speed control
Possibletogetnenish,becausetherotatingspeedis
keptconstantevenundertheloadedcondition.
Soft start feature
Softstartbecauseofsuppressedstartingshock.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
Installing the abrasive disc
►Fig.7: 1.Abrasivedisc2. Pad
Removeanydirtorforeignmatterfromthepad,and
thenattachtheabrasivedisctothepadwhilealigning
theholesintheabrasivediscwiththoseinthepad.
Adjusting the pipe length
CAUTION: When adjusting the pipe length,
hold the tool horizontally. Otherwise, the pipe
lengthmaychangeunintentionallyanditmaycause
aninjuryormalfunctionofthetool.
NOTICE: Do not extend the pipe beyond the
limit.Failuretodosomaycauseamalfunctionof
the tool.
►Fig.8: 1.Sleeve2. Pipe
Toadjustthepipelength,loosenthesleeve,thenadjust
thelengthofthepipe,andthentightenthesleeve.
Hex wrench storage
►Fig.9: 1.Hexwrench
Whennotinuse,storethehexwrenchasshowninthe
guretokeepitfrombeinglost.
Installing or removing the pad
►Fig.10: 1.Hexwrench2. Bolt 3. Pad
Toremovethepad,removetheabrasivediscfromthe
pad,andthenturntheboltcounterclockwisewithahex
wrench.Toinstallthepad,performtheremovalproce-
dureinreverse.
CAUTION: Make sure that the pad is secured
properly.Looseattachmentwillrunoutofbalance
andcauseanexcessivevibrationwhichmaycause
lossofcontrol.
Connecting a vacuum cleaner
Optional accessory
Whenyouwishtoperformoperationcleanly,connecta
Makitavacuumcleanertoyourtool.Connectahoseof
thevacuumcleanertothedustnozzleusingthefront
cu󰀨24.
►Fig.11: 1.Hoseofthevacuumcleaner2.Frontcu󰀨
24 3.Dustnozzle
Installing or removing the extension
handle
Optional accessory
Toinstalltheextensionhandle,attachtheextension
handletothetoolandsecureitwiththeknobrmly.Be
suretoinserttheendofthetoolintotheholderofthe
extensionhandle.Toremovetheextensionhandle,
performtheinstallationprocedureinreverse.
►Fig.12: 1.Extensionhandle2.Knob3. Holder
4.Endoftool5.Mountinghole
WARNING: Use the mounting hole of the tool
only for attaching the extension handle.
Usingthemountingholeforanyotherpurposemay
causeanunexpectedaccident.
OPERATION
CAUTION: Only use Makita genuine pads for
sanding (optional accessories).
CAUTION: Make sure the work material is
secured and stable. Falling object may cause
personal injury.
CAUTION: Hold the tool rmly with one hand
on the switch handle and the other hand on the
front grip when operating the tool.
CAUTION: Do not run the tool at high load
over an extended time period.Itmayresultintool
malfunctionwhichcauseselectricshock,reand/or
seriousinjury.
CAUTION: Be careful not to touch the rotating
part.
NOTICE: Never force the tool. Excessivepressure
mayleadtodecreasedsandinge󰀩ciency,damaged
pad,orshortentoollife.
NOTICE: Continuous operation at high speed
may damage work surface.
1. Positionthetoollightlyagainsttheworksurface.
Applylightpressureenoughtoalignthesandinghead
withtheworksurface.
2. Applyadditionalpressuretoengagethepad
ontheworksurface.Movethetoolinanoverlapping
patterninconstantmotiontosmooththedrywall
compound.
►Fig.13

16 ENGLISH
Operating the tool with the
extension handle
Optional accessory
CAUTION: Hold the tool rmly with one hand
on the switch handle and the other hand on the
extension handle when operating the tool with the
extension handle.
CAUTION: Take extra care for the footing and
balance when handling the tool with the extension
handle.
1. Wearthebeltfortheextensionhandleasshownin
thegure.
►Fig.14: 1. Belt
2. Attachtheholdertothebelt.
►Fig.15: 1. Holder 2. Belt
3. Puttheendoftheextensionhandleintotheholder
tosupportthetool.
►Fig.16: 1.Endofextensionhandle2. Holder
Operatethetoolinthesamewayasthetoolwithoutthe
extension handle.
►Fig.17
Youcanalsooperatethetoolwithoutusingthebeltand
theholderasshowninthegure.
►Fig.18
WIRELESS ACTIVATION
FUNCTION
Optional accessory
What you can do with the wireless
activation function
Thewirelessactivationfunctionenablescleanandcom-
fortableoperation.Byconnectingasupportedvacuum
cleanertothetool,youcanrunthevacuumcleaner
automaticallyalongwiththeswitchoperationofthetool.
►Fig.19
Tousethewirelessactivationfunction,preparefollow-
ingitems:
• Awirelessunit(optionalaccessory)
• Avacuumcleanerwhichsupportsthewireless
activationfunction
Theoverviewofthewirelessactivationfunction
settingisasfollows.Refertoeachsectionfordetail
procedures.
1. Installingthewirelessunit
2. Toolregistrationforthevacuumcleaner
3. Startingthewirelessactivationfunction
Installing the wireless unit
Optional accessory
CAUTION: Place the tool on a at and stable
surface when installing the wireless unit.
NOTICE: Clean the dust and dirt on the tool
before installing the wireless unit.Dustordirt
maycausemalfunctionifitcomesintotheslotofthe
wirelessunit.
NOTICE: To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTICE: When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1. Openthelidonthetoolasshowninthegure.
►Fig.20: 1. Lid
2. Insertthewirelessunittotheslotandthenclose
the lid.
Wheninsertingthewirelessunit,aligntheprojections
withtherecessedportionsontheslot.
►Fig.21: 1.Wirelessunit2.Projection3. Lid
4.Recessedportion
Whenremovingthewirelessunit,openthelidslowly.
Thehooksonthebackofthelidwillliftthewirelessunit
asyoupullupthelid.
►Fig.22: 1.Wirelessunit2. Hook 3. Lid
Afterremovingthewirelessunit,keepitinthesupplied
caseorastatic-freecontainer.
NOTICE: Always use the hooks on the back of
the lid when removing the wireless unit.Ifthe
hooksdonotcatchthewirelessunit,closethelid
completelyandopenitslowlyagain.
Tool registration for the vacuum
cleaner
NOTE:AMakitavacuumcleanersupportingthe
wirelessactivationfunctionisrequiredforthetool
registration.
NOTE:Finishinstallingthewirelessunittothetool
beforestartingthetoolregistration.
NOTE:Duringthetoolregistration,donotpullthe
switchtriggerorturnonthepowerswitchonthe
vacuumcleaner.
NOTE:Refertotheinstructionmanualofthevacuum
cleaner,too.
Ifyouwishtoactivatethevacuumcleaneralongwith
theswitchoperationofthetool,nishthetoolregistra-
tionbeforehand.
1. Installthebatteriestothevacuumcleanerandthe
tool.
2. Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
►Fig.23: 1.Stand-byswitch

17 ENGLISH
3. Pressthewirelessactivationbuttononthevac-
uumcleanerfor3secondsuntilthewirelessactivation
lampblinksingreen.Andthenpressthewirelessacti-
vationbuttononthetoolinthesameway.
►Fig.24: 1.Wirelessactivationbutton2. Wireless
activationlamp
Ifthevacuumcleanerandthetoolarelinkedsuccess-
fully,thewirelessactivationlampswilllightupingreen
for2secondsandstartblinkinginblue.
NOTE:Thewirelessactivationlampsnishblinking
ingreenafter20secondselapsed.Pressthewireless
activationbuttononthetoolwhilethewirelessacti-
vationlamponthecleanerisblinking.Ifthewireless
activationlampdoesnotblinkingreen,pushthewire-
lessactivationbuttonbrieyandholditdownagain.
NOTE:Whenperformingtwoormoretoolregistra-
tionsforonevacuumcleaner,nishthetoolregistra-
tiononebyone.
Starting the wireless activation
function
NOTE:Finishthetoolregistrationforthevacuum
cleanerpriortothewirelessactivation.
NOTE:Refertotheinstructionmanualofthevacuum
cleaner,too.
Afterregisteringatooltothevacuumcleaner,the
vacuumcleanerwillautomaticallyrunsalongwiththe
switchoperationofthetool.
1. Installthewirelessunittothetool.
2. Connectthehoseofthevacuumcleanerwiththe
tool.
►Fig.25
3. Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
►Fig.26: 1.Stand-byswitch
4. Pushthewirelessactivationbuttononthetool
briey.Thewirelessactivationlampwillblinkinblue.
►Fig.27: 1.Wirelessactivationbutton2. Wireless
activationlamp
5. Pulltheswitchtriggerofthetool.Checkifthe
vacuumcleanerrunswhiletheswitchtriggerisbeing
pulled.
Tostopthewirelessactivationofthevacuumcleaner,
pushthewirelessactivationbuttononthetool.
NOTE:Thewirelessactivationlamponthetoolwill
stopblinkinginbluewhenthereisnooperationfor
2hours.Inthiscase,setthestand-byswitchonthe
vacuumcleanerto“AUTO”andpushthewireless
activationbuttononthetoolagain.
NOTE:Thevacuumcleanerstarts/stopswithadelay.
Thereisatimelagwhenthevacuumcleanerdetects
aswitchoperationofthetool.
NOTE:Thetransmissiondistanceofthewirelessunit
mayvarydependingonthelocationandsurrounding
circumstances.
NOTE: When two or more tools are registered to one
vacuumcleaner,thevacuumcleanermaystartrun-
ningevenifyoudonotpulltheswitchtriggerbecause
anotheruserisusingthewirelessactivationfunction.
Description of the wireless activation lamp status
►Fig.28: 1.Wirelessactivationlamp
Thewirelessactivationlampshowsthestatusofthewirelessactivationfunction.Refertothetablebelowforthe
meaningofthelampstatus.
Status Wireless activation lamp Description
Color
On Blinking
Duration
Standby Blue 2hours Thewirelessactivationofthevacuumcleanerisavailable.The
lampwillautomaticallyturno󰀨whennooperationisperformed
for2hours.
When
the tool is
running.
Thewirelessactivationofthevacuumcleanerisavailableandthe
toolisrunning.
Tool
registration
Green 20seconds Readyforthetoolregistration.Waitingfortheregistrationbythe
vacuumcleaner.
2seconds Thetoolregistrationhasbeennished.Thewirelessactivation
lampwillstartblinkinginblue.
Cancelling
tool
registration
Red 20seconds Readyforthecancellationofthetoolregistration.Waitingforthe
cancellationbythevacuumcleaner.
2seconds Thecancellationofthetoolregistrationhasbeennished.The
wirelessactivationlampwillstartblinkinginblue.
Others Red 3seconds Thepowerissuppliedtothewirelessunitandthewirelessactiva-
tionfunctionisstartingup.
O󰀨 - - Thewirelessactivationofthevacuumcleanerisstopped.

18 ENGLISH
Cancelling tool registration for the
vacuum cleaner
Performthefollowingprocedurewhencancellingthe
toolregistrationforthevacuumcleaner.
1. Installthebatteriestothevacuumcleanerandthe
tool.
2. Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
►Fig.29: 1.Stand-byswitch
3. Pressthewirelessactivationbuttononthevac-
uumcleanerfor6seconds.Thewirelessactivation
lampblinksingreenandthenbecomered.Afterthat,
pressthewirelessactivationbuttononthetoolinthe
sameway.
►Fig.30: 1.Wirelessactivationbutton2. Wireless
activationlamp
Ifthecancellationisperformedsuccessfully,thewire-
lessactivationlampswilllightupinredfor2seconds
andstartblinkinginblue.
NOTE:Thewirelessactivationlampsnishblinkingin
redafter20secondselapsed.Pressthewirelessacti-
vationbuttononthetoolwhilethewirelessactivation
lamponthecleanerisblinking.Ifthewirelessacti-
vationlampdoesnotblinkinred,pushthewireless
activationbuttonbrieyandholditdownagain.

19 ENGLISH
Troubleshooting for wireless activation function
Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,
donotattempttodismantlethetool.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakitareplace-
mentpartsforrepairs.
State of abnormality Probable cause (malfunction) Remedy
Thewirelessactivationlampdoes
notlight/blink.
Thewirelessunitisnotinstalledinto
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Installthewirelessunitcorrectly.
Theterminalofthewirelessunitand/or
theslotisdirty.
Gentlywipeo󰀨dustanddirtontheterminalofthe
wirelessunitandcleantheslot.
Thewirelessactivationbuttononthe
toolhasnotbeenpushed.
Pushthewirelessactivationbuttononthetool
briey.
Thestand-byswitchonthevacuum
cleanerisnotsetto“AUTO”.
Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
Nopowersupply Supplythepowertothetoolandthevacuum
cleaner.
Cannotnishtoolregistration/can-
cellingtoolregistrationsuccessfully.
Thewirelessunitisnotinstalledinto
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Installthewirelessunitcorrectly.
Theterminalofthewirelessunitand/or
theslotisdirty.
Gentlywipeo󰀨dustanddirtontheterminalofthe
wirelessunitandcleantheslot.
Thestand-byswitchonthevacuum
cleanerisnotsetto“AUTO”.
Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
Nopowersupply Supplythepowertothetoolandthevacuum
cleaner.
Incorrectoperation Pushthewirelessactivationbuttonbrieyand
performthetoolregistration/cancellationprocedures
again.
Thetoolandvacuumcleanerareaway
fromeachother(outofthetransmission
range).
Getthetoolandvacuumcleanerclosertoeach
other.Themaximumtransmissiondistanceis
approximately10mhoweveritmayvaryaccording
tothecircumstances.
Beforenishingthetoolregistration/
cancellation;
-theswitchtriggeronthetoolispulled
or;
-thepowerbuttononthevacuum
cleaneristurnedon.
Pushthewirelessactivationbuttonbrieyand
performthetoolregistration/cancellationprocedures
again.
Thetoolregistrationproceduresfor
thetoolorvacuumcleanerhavenot
nished.
Performthetoolregistrationproceduresforboththe
toolandthevacuumcleaneratthesametiming.
Radiodisturbancebyotherappliances
whichgeneratehigh-intensityradio
waves.
Keepthetoolandvacuumcleanerawayfromthe
appliancessuchasWi-Fidevicesandmicrowave
ovens.

State of abnormality Probable cause (malfunction) Remedy
Thevacuumcleanerdoesnotrun
alongwiththeswitchoperationof
the tool.
Thewirelessunitisnotinstalledinto
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Installthewirelessunitcorrectly.
Theterminalofthewirelessunitand/or
theslotisdirty.
Gentlywipeo󰀨dustanddirtontheterminalofthe
wirelessunitandcleantheslot.
Thewirelessactivationbuttononthe
toolhasnotbeenpushed.
Pushthewirelessactivationbuttonbrieyandmake
surethatthewirelessactivationlampisblinking
inblue.
Thestand-byswitchonthevacuum
cleanerisnotsetto“AUTO”.
Setthestand-byswitchonthevacuumcleanerto
“AUTO”.
More than 10 tools are registered to the
vacuumcleaner.
Performthetoolregistrationagain.
Ifmorethan10toolsareregisteredtothevacuum
cleaner,thetoolregisteredearliestwillbecancelled
automatically.
Thevacuumcleanererasedalltool
registrations.
Performthetoolregistrationagain.
Nopowersupply Supplythepowertothetoolandthevacuum
cleaner.
Thetoolandvacuumcleanerareaway
fromeachother(outofthetransmission
range).
Getthetoolandvacuumcleanerclosereachother.
Themaximumtransmissiondistanceisapproxi-
mately10mhoweveritmayvaryaccordingtothe
circumstances.
Radiodisturbancebyotherappliances
whichgeneratehigh-intensityradio
waves.
Keepthetoolandvacuumcleanerawayfromthe
appliancessuchasWi-Fidevicesandmicrowave
ovens.
Thevacuumcleanerrunswhilethe
tool'sswitchtriggerisnotpulled.
Otherusersareusingthewireless
activationofthevacuumcleanerwith
their tools.
Turno󰀨thewirelessactivationbuttonoftheother
toolsorcancelthetoolregistrationoftheother
tools.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
Storing the tool in the tool bag
Whenstoringthetoolinthetoolbag,xitwiththehook
andloopfastenersasshowninthegure.
►Fig.31: 1.Hookandloopfastener2.Tool
When storing the tool and the extension handle in the
toolbag,xthemwiththehookandloopfastenersas
showninthegure.
►Fig.32: 1.Hookandloopfastener2.Extension
handle 3.Tool
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessoriesorattachmentsmightpresentariskof
injurytopersons.Onlyuseaccessoryorattachment
foritsstatedpurpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Abrasivedisc
• Pad
• Extensionhandle(withbeltandholder)
• Wirelessunit
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
di󰀨erfromcountrytocountry.
20 ENGLISH