Mamas & Papas Bubble bouncing cradle User manual

instructions
bubble bouncing cradle
ABUB01: V1/06/07
© Mamas & Papas (Holdings) Ltd. 2007
WARNING - IMPORTANT KEEP
FOR FUTURE REFERENCE.
Bubble Cradle V1.indd 1 8/6/07 14:24:50

BuBBle Bouncing cradle
component list
Item Description Qty
1 Leg connector 1
2 Legs 2
3 Backrest frame 1
4 Seat frame 1
5 Frame screws 2
Item Description Qty
6 Vibration unit 1
7 Cover 1
8 Play arch 1
9 Toys 3
10 Head hugger 1
THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ CAREFULLY
AND RETAIN FOR FUTURE REFERENCE.
The correct use and maintenance of your cradle will ensure it gives a long
and trouble free use. When somebody else is using your cradle, ensure they
also know how to use and adjust it and all necessary safety precautions.
The safety of your child is your responsibility.
After sales Service: If you need assistance, spare parts or you are unhappy with any aspect
of the goods please contact Customer Services on: [phone], or e-mail us at:
customer.ser[email protected]. Visit our website at www.mamasandpapas.com
for the latest product information.
1
10
8
7
- 2 -
2
3
9
5
4
6
Bubble Cradle V1.indd 2 8/6/07 14:24:51

- 3 -
assemBling the frame
A: Slot the ends of
the legs into the holes
in the ends of the leg
connector.
B: Slot the backrest
frame through the
mouldings on the seat
frame as shown in
the diagram. Fasten
the mouldings to the
backrest frame using
the two frame screws.
C: Slot the ends of the
backrest frame onto
the top of the legs.
D: Slot the vibration
unit into the slot in
seat section of the
front of the backrest
frame.
a
c
B
d
Bubble Cradle V1.indd 3 8/6/07 14:24:52

- 4 -
fitting the cover
A: Slip the back of
the cover over the
backrest frame.
B: Slot the front of
the cover over the
seat section of the
backrest frame.
C: Slot the elasticated
hole in the front of
the cover around the
top of the vibration
unit.
D: Push the seat
section of the
backrest frame down
until it locks over the
lugs on the pivots.
To remove the cover,
reverse the procedure
for fitting it.
a
B
c
d
Bubble Cradle V1.indd 4 8/6/07 14:24:52

- 5 -
fitting the toy arch and toys
A: Slot the two plastic
clips on the ends of
the toy arch over the
seat frame above the
pivot.
B: Attach the toys
to the toy arch by
looping the straps on
the toys over the toy
arch. Fasten the velcro
tabs on both ends of
the straps together.
a
B
Bubble Cradle V1.indd 5 8/6/07 14:24:54

- 6 -
using the viBration unit
Inserting/changing
the batteries.
Place the vibration
unit upside down
and remove the
screw holding the
battery cover in place
using a small cross-
head screwdriver.
Insert two type
“AA” batteries as
shown in the battery
compartment.
Ensure the batteries
are correctly inserted.
Incorrectly fitted
batteries may damage
the unit. Refit the
battery cover.
Operating the
vibration Unit.
Turn the dial clockwise
to start the unit. The
further clockwise
the dial is turned
the stronger the
sensation. Turn the
dial anti-clockwise
to turn the vibration
down and off.
Note: It may be
necessary to increase
the strength of the
vibration as your
child grows or with
fluctuations in the
battery power.
Bubble Cradle V1.indd 6 8/6/07 14:24:55

- 7 -
using the safety harness
Warning: Never place
your child in the seat
without fitting and
adjusting the safety
harness.
A: Locking the
harness. Push the
locking catch 1into
the buckle 2until
it clicks into place.
Repeat for the second
lock.
B: Releasing the
harness. Push the
two tabs 3on the
locking catch in and
detach the buckle.
C: Adjusting the
harness length. To
loosen the harness
feed the webbing
back through the
locking catch. To
tighten the harness
pull the free ends of
the webbing outwards
4.
12
3
3
4
a
B
c
Bubble Cradle V1.indd 7 8/6/07 14:24:55

- 8 -
instructions for safe use
WARNING: Never leave your child unattended in the
rocking cradle.
Not recommended for children who can sit up by
themselves (6 months approximately: until 9 kgs).
WARNING: It is dangerous to put this rocking cradle on an
elevated surface.
Never attempt to lift the rocking cradle using the toy arch.
Always use the safety harness, see page 7.
Assemble and adjust the rocking cradle with care.
Occasionally clean the metal and plastic parts with a
proprietary polish. Do not use abrasives or bleach.
The fabric may be sponged clean on the frame or removed
for washing. Check the attached wash care label for more
information.
Prolonged and direct exposure to the bright sunlight can
change the fabrics colours. Try to limit if possible.
•
•
•
•
•
•
•
•
•
ALL OUR PRODUCTS ARE MADE FROM THE FINEST QUALITY MATERIALS AND ARE
MANUFACTURED UNDER THE STRICTEST QUALITY CONTROLS
We guarantee all our products or part thereof, for a period of twelve months from the date
of delivery to the consumer against faulty manufacture. This guarantee is not effective
against damage caused as a result of incorrect usage of the product or accidental damage.
This in no way affects your statutory rights.
After sales Service: If you need assistance, spare parts or you are unhappy with any aspect
of the goods please contact Customer Services on: [phone], or e-mail us at:
customer.ser[email protected]. Visit our website at www.mamasandpapas.com
for the latest product information.
Bubble Cradle V1.indd 8 8/6/07 14:24:55