Manhattan Comfort Libra Long Floating 45.35 Entertainment... User manual

Ed. 001, 2020/05 - Manhattan Comfort.
Libra Long Floating 45.35
Entertainment Center
Model # 237BMC6, 237BMC8, 237BMC9, 237BMC97
888-230-2225
[e-mail]
40
lb
The indicated values consider static weights and evenly distributed over the parts.
11
lb
11
lb
11
lb
11
lb
22
lb

n.° ID Parts Identification (Description) Quantity
REAR VIEW
2
1
2
2
1
01
04
06
02
05
03
1
2
INCLUDED IN THE PACKAGE
Left and Right Panel
Rear Column
Middle Panel
Upper Rear Bar
Upper and Lower Shelf
Bar for wall
07
08
09
10
2
Middle Shelf
2
Left and Right Side Panel
1
Middle Partition
1
Lower Rear Support
05
05
06
06
07
10
For fixing
behind
the panel
04
For fixing
on the wall
03
03
07
02
01
06
06
07
08
05
05
01
09
For fixing
on the wall

3
INCLUDED IN THE HARDWARE
TOOLS NEEDED
Simple hammer.Flat head and phillips
screwdriver.
Electric drill and electric screwdriver with
drill bit Ø1/2 inch and phillips tips.
Level indicator.
!IMPORTANT! Two people are recommended to assemble and install this product.
6x
A20x B6x
C
12x
D28x E6x F
6x
G6x
H2x I
24x
J4x K4x L

4
DETAIL 1
• Line the floor with
the foam mantle of the
packing to protect the parts
and arrange the Panels (01)
and (02) with the rear face
upwards, correctly checking the
position of each according the
holes and as shown in the drawing.
• Align the edges of the Panels (01)
and (02) and fix them together by
applying the steel plates (C) with
bolts (D), as shown in the DETAIL 1.
• Position the Rear Columns (03)
behind the Panels (01) with dowels (A)
according to the drawing, and fix them
with bolts (E).
• Fix Upper Rear Bar (04), positioning it
correctly behind the panels with dowels (A)
and glue (I) and applying the bolts (E).
ATTENTION!
APPLY GLUE.
04
02
01
Rear face
Rear face
STEP 1
03
01
Rear face
03
STEP 2
06
07
08
07
DETAIL 2
• Connect the Middle Shelves (06) at the Left and Right
Sideboards (07) and the Middle Partition (08) with dowels
Ø6 x 30mm (B) and cam lock hardware (F + G).
• After finishing fixing, apply the adhesive caps (H) to the
holes in the drums (G).
06
STEP 3
• Fix the Shelves (05) and (06) in the
Panels (01) and (02) with dowels (B)
and bolts (J).
DETAIL 3
02
Rear face
01
Rear face
01
Rear face
06
06
05
05
07
04
03
03

STEP 4
5
55.00in*
23.00in
Minimum fixing distance of the
middle point of the Support (09)
and Bar (10) for the panel
installation close to walls corner.
10
ATENTION!
Before installing the panel, check the
conditions of the wall for strength to
properly support and anchor the
weight of the suspended furniture,
including equipment and objects
that may be fixed to the panel.
The Kap Toggle bushings (K) supplied
with the product are for hollow walls or
dry wall type.
Check the type of wall on which the
installation will be made and, if
necessary, look for more suitable
bushings or fastening systems.
To mark the position and fix the
Support (09) and the Bar (10) on the
wall, check the level of the parts.
• Mark the position of the holes on the
wall to fix the Support (09) and the
Bar (10), as shown in the drawing
and using the bars themselves as a
reference.
• With electric drill and drill bit Ø1/2in,
make the holes in the wall.
• Apply the bushings (K) into the holes
in the wall and fix the Support (09)
and the Bar (10) with the bevelled
edge facing up and to the wall,
applying the bolts 1/4 x 2.1/4",
as indicated in the drawing.
1/2 inch hole
in the wall
Kap Toggle
bushing (K)
Bolt
1/4 x 2.1/4 inches
*The heights of 22.00 inches and 55.00
inches indicated in the drawing, between
the floor and the lower edge of the
Support (09) and the Bar (10),
respectively, are only suggestive, to
install the Panel with its lower edge than
approximately 4 inches from the floor.
DETAIL 4
22.00in*
09