Manhattan Comfort HOPKINS 2GLF User manual

V.10102022
Assembly Guide
2GLF

2GLF
Page 2
SUPPORT SITE
QR CODE
Stuck? Question? We are here to help.
tel: [phone]
e-mail: [email protected]
View our assembly video online:
WWW.MANHATTANCOMFORT.COM
TOOLS REQUIRED
 Do not throw away packaging materials until assembly is complete.
 Assemble item on a soft surface, such as cardboard or carpet, to protect finish.
 Proper assembly requires two people.
FOR BEST RESULTS:
Before beginning the assembly process,
ensure all boxes and parts have been delivered.
STOP!
STOP!

Page 3
2GLF
Included in this package:
A. TOP (1)
B. SHELF (1)
C. BOTTOM (1)
D. LEFT END (1)
E. RIGHT END (1)
F. UPRIGHT (1)
G. BACK (1)
H. ADJUSTABLE SHELF (4)
J. MOLDING (1)
K. SKIRT (1)
O. LEFT DOOR (1)
P. RIGHT DOOR (1)

Hardware Identification
2GLFPage 4

319 Ridge Rd. Dayton, NJ 08810
908-888-0818
All Manhattan Comfort furniture products are warranted, to the original purchaser at the
time of purchase and for a period of 30 days thereafter.
Our warranty is limited to new products purchased in factory sealed cartons. This war -
ranty is valid in the United States of America and Canada.
In order to provide you with timely assistance, please thoroughly inspect your furniture
for missing or defective parts immediately after opening the carton.
Manhattan Comfort offers a 30-day parts replacement warranty on all items.
Our furniture products are not intended for outdoor use.
THE WARRANTY DOES NOT COVER:
- Defects/damages by improper assembly or disassembly.
- Defects/damages caused by shipping. Claims for damage during transit should be
placed immediately to the transportation company.
- Defects/damages caused by inappropriate use of the furniture.
WARRANTY POLICY

Step 1
◆Fasten the MOLDING (J) to the TOP (A) and the SKIRT (K) to the BOTTOM (C).
Use six FLAT HEAD SCREWS (5).
2GLFPage 6

◆Fasten the UPRIGHT (F) to the SHELF (B) and the BOTTOM (C) .
Use four FLAT HEAD SCREWS (5).
Step 2
Page 7
2GLF

Fasten the RIGHT END (E) to the SHELF (B), BOTTOM (C) and the TOP (A).
Use eleven FLAT HEAD SCREWS (5).
◆
Step 3
2GLFPage 8

Step 4
◆Fasten the LEFT END (D) to the TOP (A), SHELF (B) and the BOTTOM (C).
Use eleven FLAT HEAD SCREWS (5).
Page 9
2GLF

Make equal margins along all four edges of the BACK (G). Push on opposite
corners of your unit if needed to make it "square".
Using your hammer, fasten the BACK (G) to your unit using the NAILS (7).
NOTE : Be sure to tap NAILS into the holes that line up over the UPRIGHT (F).
! Caution !
Do not stand the unit upright without the
BACK fastened.
The unit may collapse.
Step 5
◆
◆
◆
2GLFPage 10

Step 6
◆Fasten the HINGES (2) to the DOORS (O and P). Use twelve FLAT HEAD SCREWS (8).
Fasten the PULLS (1) to the DOORS (O and P). Use four MACHINE SCREWS (6).
Page 11
2GLF

Step 7
◆
◆
◆
Carefully stand your unit upright.
Faten the DOORS (O and P) to the ENDS (D and E). Use the FLAT HEAD SCREWS (8) in the HINGES.
You should start each SCREW a few turns before completely tightening any of them.
2GLFPage 12

Step 8
◆Insert the METAL PINS (3) into the hole location of your choice in the ENDS (D and E) and UPRIGHT (F).
Set The ADJUSTABLE SHELVES (H) onto the METAL PINS.
Page 13
2GLF

Step 9
◆
◆
◆
Open the FURNITURE TIPPING RESTRAINT KIT and fasten the SAFETY STRAP to the TOP (A).
Use the SHORT SCREW through the hole in the strap and into the top surface of the TOP (1).
Place your unit in its final location.
NOTE: The following instructions show your unit being fastened to a wall stud. If you are not
fastening your unit wall stud, go to the next step now.
1st- Locate the center of a stud in your wall near your unit and mark it with a pencil.
2nd- Drill a 1/8" hole on the mark and into the stud in your wall.
3rd- Fasten the unit to the wall. Use the LONG SCREW through the other end of the SAFETY
STRAP and into the 1/8'' hole.
2GLFPage 14
Mark and drill
a 1/8" hole into
the wall stud.
2nd
1st
3rd

Mark and drill
a 3/8" hole into
the wall stud.
Step 10
◆
◆
◆
1st- With your pencil, strike a mark through the center of the hole in the SAFETY STRAP.
2nd- Drill a 3/8" hole on the mark.
3rd- While you squeeze the wings together, gently tap the WALL ANCHOR from the FURNITURE
TIPPING KIT (96) into the hole until it is even with the surface of the wall.
4th- Turn the LONG SCREW through the hole in the SAFETY STRAP and into the WALL ANCHOR.
NOTE: You will need to turn the LONG SCREW multiple turns to completely tighten and secure your
unit.
Peel the APPLIQUES (4) from the applique card and stick them over the heads of the SCREWS
in the ENDS.
Page 15
2GLF
2nd
1st
3rd
4th

2GLFPage 16
Step 11
No Load
35 lbs
25 lbs
25 lbs
25 lbs
25 lbs
30 lbs
30 lbs