Manhattan Comfort Tribeca Shoe Closet User manual

Tribeca Shoe Closet

13
Lb
Before starting
Prepare the room before starting the assembly,
leaving it completely clean and the area in
good condition to start the work.
Use the cardboard of the packaging and
the foam sheets protection to separate and
support the parts removed from the boxes.
1
13
Lb
13
Lb
13
Lb
13
Lb
Dimension:
W: 32.67" H: 50.59" D: 15.94"
QUANTITY OF PEOPLE
TO ASSEMBLE THIS
FURNITURE
REQUIRED TOOLS

2
06
06
06
09
09
02
01
08
03
08
05
04
07
07
07
PART DESCRIPTION QUANTITY
01 TOP 01
02 RIGHT SIDE 01
03 FIXED SHELF 01
04 LEFT SIDE 01
05 BASE 01
06
FEET
04
07
BACK COVER
03
08 SUSPENDED SHELF 02
09 DOOR 02
HARDWARE
AF
04x B04x C08x E04x
D04x 34x
GH08x J
I02x 24x KL01x
02x 02x
GLUE
N
M01x 02x OQ01x
01x P04x
FRONT VIEW REAR VIEW

3
STEP 1
STEP 3
STEP 2
- Insert the hardware (B) on the pieces (01, 02 and 04).
- Insert the accessory (H) on the parts (02 and 04).
B
04x
01
02
04
B
B
B
B
H
H
H
H
H
H
H
H
H
08x
- Join the parts (01 and 02) with hardware (A).
- Fix the part (03) into part (02) with a bolts (C).
C
C
C
C
A
A
05
04
A02x
C06x
02
01
03
A
A
- Join the parts (04 and 01) with the hardware (A).
- Fix the part (03) into part (04) with a bolts (C).
- Connect the base (05) whit bolts (C).
02x
A
C02x
C
C
03
01

STEP 4
STEP 5
STEP 6
4
P+E
P+E
07
07
07
07
- Fix the feet (07) under the base (05), using bolts (P).
- Apply the plastic covers (E) on top of the bolts (P)
L
USE THE GLUE (L)
BEFORE FASTENING
THE FEET (07).
07
- Fix back cover (06) with nails (F).
- Insert the hardware (K) among pieces (06).
- Insert the shelfs (08) shawn in image.
08
08
F
K
02x
34x
06
06
06
05
P
04x
04x
E

STEP 8
5
STEP 7
Approach as close
as possible to the wall
STEP 9
WALL
Attention! This step is very important!
- Fix the hinges (D) in the doors (09) with bolts (J).
- Fix the handles (I) in the doors (09) with bolts (G).
G
I
D
J
D+2J D+2J
D+2J
G
I
02x
02x
04x
08x
09
09
- Fix the hinge connectors (D) of the doors (09) in the
parts (02 and 04) with a bolts (J), taking the marking as
reference for correct positioning.
D+2J
4J
4J
09
09
J
16x
04
02
You need to attach the Shoe Closet on the wall to
avoid any tip over risk. Follow the procedures as showed
below.

08
6
Screws the hardware O passing
through the hardware M until the
hardware Q.
*press the wings of the hardware Q
to put in the hole that you drilled in the wall.
Pass the hardware M through the hole of the part 08 as showed in the
figure above. You will need a pencil to mark where you should drill the
wall with a 5/16" drill bit to put in the hardware Q.
wings
wings
Hardware P, plugged in the wall.
Q
M
N
Screws the hardware N passing through the hardware M and fit in
below the piece 01.
O
N
Q
M