Manntek SBC Original operating manual

manntek.se
SBC Service instruction
Cable release – 6"

2 of 7 - Version 181009
MATERIAL:AL,SS
PARTS NEEDED FOR SERVICE:O-ring kit (see p.3)
TYPE OF CONNECTION:Threaded and Flanged couplings have the
same service instruction.
PERFORM A SERVICE:If leaking
According to application service plan, (see regular
service p.3)
Change of media
P
LEASE NOTE
!
Make sure that you are using the right type of O-rings and seals for the
media you are using. We are using a standard silicone based grease
for standard media, for special media please contact us.

3 of 7 - Version 181009
MAINTENANCE AND SERVICE INSTRUCTION
Always depressurise the system and rinse off the parts before beginning any
maintenance work. Use protective goggles. Do not handle O-ring seals if the
material appears charred, gummy or sticky.
Use tweezers and wear neoprene or PVC gloves. Do not touch adjacent parts with
unprotected hands. Rinse off the parts once again before starting the “daily
inspection”
DAILY INSPECTION
All couplings should be briefly inspected at the start of each day’s operation. Check for dirt,
seal damage and any obvious physical damage (such as impacts, etc.).
REGULAR SERVICE
Regular service interval is very much depending on local regulations and application
conditions. If nothing else is specified and it is a new application with unknown parameters
we recommend to make a first service after one year and decide then depending on the
inspection result about further intervals.
The service procedure shall be as follows:
1. Exchange seals.
2. Replace worn or damaged components.
USE ONLY ORIGINAL MANNTEK SPARE PARTS FOR MAINTENANCE.
O-ring kit (O-O6-yy)
yy means the O-ring material key according to the product catalogue. You will find it also as
the 6th to 9th sign in the serial number (e.g. O645Dxxyy).

4 of 7 - Version 181009
A
FTER RELEASE
When the coupling should go into service there is a
danger that the fluid will spurt out. Special protective
measures such as personal protective equipment must
therefore be adopted. Always ensure the system is
cleaned in a proper manner. After cleaning, remove
any residue from the cleaning agent.
a. Wear suitable personal protective
equipment.
b. Make sure that the coupling is
depressurized and empty.
c. Clean the coupling before disassembly (use
cleaning agent suitable for the pumped fluid).
D
ISASSEMBLE
Unscrew the three screws that lock the spindle
steering.
There is a distance pin in the piston
protruding from the housing.
For disassembling a support plate with a hole in the
middle will avoid any damage of the piston.
Tool: Allen Key No. 6
D
ISASSEMBLE
Press down the spindle steering and turn it free.
Release it carefully
Piston guide is spring loaded. Risk of
injury.
Using our special tool makes work easier and
therefore increases safety.
Repeat the same procedure with the second half.
D
ETAIL PARTS AFTER DISASSEMBLING
Take out all the parts from the body
1. Body
2. Spindle steering, spring cap and bushing
3. Piston
4. Spring
1
2
3
4

5 of 7 - Version 181009
P
ISTON
O-
RING
Replace the O-ring (pos.3) on the piston with a new
greased O-ring. Have an equal pressure around the O-
ring. The O-ring must be pressed into the groove on
the piston.
Use only grease which is suitable for O-ring material.
For mounting the new O-ring use MannTek spare
parts only. Special tools are helpful for a good fit of the
O-ring.
I
NNER BODY
O-
RING
Remove the nine screws and remove the coupling
flange from the body.
Replace the O-ring (pos.19) on the body with a new
greased O-ring. Use only grease which is suitable for
the O-ring material.
Mount back the coupling flange to the body, use
Loctite® 243 on the nine screws.
Tool: Allen Key 10 mm
M
OUNTING PISTON
The piston is bigger in diameter than the three
brackets for the piston guide.
Introduce the piston as shown. Put it into a relaxing
position in the valve seat. Take care, the piston is
sticking out on the other side.
R
EASSEMBLE COUPLING HALVES
Fit the spring with spring cap and spindle steering.
Press down the spindle steering and turn, to fix it in its
position.

6 of 7 - Version 181009
L
OCKING THE SPINDLE STEERING
Fit the screws into the given holes in the body and
fixate the spindle steering by mounting the three
locking screws. Use Loctite® 243 for locking the
screws.
O
UTER BODY
O-
RING
Replace the O-ring (pos.15) on the body with a new
greased O-ring.
Use only grease which is suitable for O-ring material.
R
EASSEMBLE COUPLING
Set both halves onto each other and press them
carefully together.
It is important that the bodies align to each
other when pressing the halves together. Do
it carefully, not to destroy the lip-seal.
Using a press and a fixture makes work easier
F
IX THE
C
LAMPS AND RING
Place the clamps (b) over the coupling flanges smaller
diameter (d) and put the ring (a) over the clamps to
hold them in place. Make sure that the bolts (c) are
placed on either side of the clamps. After the coupling
is completely reassembled provide a pressure test
according to test procedure on page 8.
N
OTE WHEN INSTALLING
Direction of release
Loctite® is registered trademark of Henkel.
b
a
c
d
c

7 of 7 - Version 181009
TEST PROCEDURE
After each service a pressure and tightness test of each coupling is mandatory. Test each
half separately before you connect both halves with the breaking pins. The following test
parameters are in accordance with EN12266, EN14432 and ISO5208:
Shell tightness test (water): 1,5 x Working Pressure (see 1.2) stop time 1 min.
Seat tightness test (air): 6 bar +/- 1bar stop time 15 s.
0,1 x Working Pressure stop time 15 s.
If a pressure test should be achieved for the coupling mounted in an assembly follow the
respective test instructions for the equipment.
Approved couplings get stamped on the piston.
Number tested: 100%
STORAGE
Store coupling in a dry, dust free, dark place, in ambient temperature.
© Copyright 2012 Mann Teknik AB. Mann Teknik AB reserves the right to make changes at any time in
prices, materials, specifications and models and to discontinue models without notice or obligations.