Marantz SR-6001 User manual
Model SR6001 User Guide
AV Surround Receiver
SR6001UDFU0cover.inddISR6001UDFU0cover.inddI 06.12.214:13:17PM06.12.214:13:17PM
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE
DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the
NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by tuning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
NOTE:
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
IMPORTANT SAFETY
INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to
meet strict quality and safety standards. There are,
however, some installation and operation precautions
which you should be particularly aware of.
1. Read Instructions – All the safety and
operating instructions should be read before
the product is operated.
2. Retain Instructions – The safety and
operating instructions should be retained for
future reference.
3. Heed Warnings – All warnings on the product
and in the operating instructions should be
adhered to.
4. Follow Instructions – All operating and use
instructions should be followed.
5. Cleaning – Unplug this product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Attachments – Do not use attachments not
recommended by the product manufacturer
as they may cause hazards.
7. Water and Moisture – Do not use this product
near water-for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and
the like.
8. Accessories – Do not place this product on
an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious
injury to a child or adult, and serious damage
to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use
a mounting accessory recommended by the
manufacturer.
9. A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10. Ventilation – Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions
have been adhered to.
11. Power Sources – This product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your product dealer or local
power company. For products intended to
operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization – This product
may be equipped with a polarized
alternatingcurrent line plug (a plug having
one blade wider than the other). This plug will
fit into the power outlet only one way. This is
a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of
the polarized plug.
AC POLARIZED PLUG
SR6001UDFU0cover.inddIISR6001UDFU0cover.inddII 06.12.214:13:17PM06.12.214:13:17PM
FIGURE 1
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
13. Power-Cord Protection – Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit
from the product.
14. Protective Attachment Plug – The product
is equipped with an attachment plug having
overload protection. This is a safety feature.
See Instruction Manual for replacement or
resetting of protective device. If replacement
of the plug is required, be sure the service
technician has used a replacement plug
specified by the manufacturer that has the
same overload protection as the original plug.
15. Outdoor Antenna Grounding – If an outside
antenna or cable system is connected to the
product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static
charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast
and supporting structure, grounding of
the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location
of antennadischarge unit, connection to
grounding electrodes, and requirements for
the grounding electrode. See Figure 1.
16. Lightning – For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods
of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
17. Power Lines – An outside antenna system
should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might be
fatal.
18. Overloading – Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire
or electric shock.
19. Object and Liquid Entry – Never push objects
of any kind into this product through openings
as they may touch dangerous voltage points
or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind
on the product.
20. Servicing – Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualified service personnel.
21. Damage Requiring Service – Unplug
this product from the wall outlet and refer
servicing to qualified service personnel under
the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by
the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or damaged
in any way, and
f. When the product exhibits a distinct change
in performance this indicates a need for
service.
22. Replacement Parts – When replacement
parts are required, be sure the service
technician has used replacement parts
specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
23. Safety Check – Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in proper
operating condition.
24.Wall or Ceiling Mounting – The product should
be mounted to a wall or ceiling only as
recommended by the manufacturer.
25. Heat – The product should be situated away
from heat sources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
DECLARATION OF CONFORMITY
U.S. Responsible Party: Marantz America, Inc.
100 Corporate Drive,
Mahwah, NJ, 07430, U.S.A.
TEL: 630-741-0300
Type of Product:
Model:
AV Surround Receiver
SR6001
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
SR6001UDFU0cover.inddIIISR6001UDFU0cover.inddIII 06.12.214:13:18PM06.12.214:13:18PM
ENGLISH
1
TABLE OF CONTENTS
SETUP ..................................................26
ONSCREEN DISPLAY MENU SYSTEM.........................26
1 INPUT SETUP .............................................................28
2 SPKR (SPEAKER) SETUP ..........................................31
ERROR MESSAGES .......................................................34
3 SURROUND SETUP ...................................................37
4 VIDEO SETUP .............................................................39
5 PREFERENCE ............................................................40
6 ACOUSTIC EQ ............................................................42
BASIC OPERATION (PLAY BACK).....44
SELECTING AN INPUT SOURCE...................................44
SELECTING THE SURROUND MODE...........................44
ADJUSTING THE MAIN VOLUME ..................................44
NIGHT MODE...................................................................44
ADJUSTING THE TONE (BASS & TREBLE) CONTROL
..44
DIALOGUE NORMALIZATION MESSAGE.....................44
VIDEO CONVERT............................................................45
I/P CONVERT...................................................................45
TEMPORARILY TURNING OFF THE SOUND .................45
USING THE SLEEP TIMER .............................................45
SURROUND MODE .............................46
SURROUND.....................................................................46
SOURCE DIRECT ...........................................................46
PURE DIRECT ................................................................46
OTHER FUNCTION..............................50
TV AUTO ON/OFF FUNCTION........................................50
ATTENUATION TO ANALOG INPUT SIGNAL ................50
LISTENING THROUGH HEADPHONES
.........................50
DOLBY HEADPHONE MODE .........................................50
VIDEO ON/OFF................................................................50
DISPLAY MODE...............................................................51
SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO
INPUT ..............................................................................51
RECORDING AN ANALOG SOURCE.............................51
SPEAKER A/B ..................................................................51
7.1 CH INPUT...................................................................52
AUX2 INPUT.....................................................................52
LIP.SYNC ..........................................................................52
INTRODUCTION ....................................2
PRECAUTIONS......................................2
DESCRIPTION .......................................2
FEATURES .............................................5
ACCESSORIES......................................5
FRONT PANEL ......................................6
FL DISPLAY AND INDICATOR ..........................................7
REAR PANEL .........................................8
REMOTE CONTROL OPERATION .......9
FUNCTION AND OPERATION ..........................................9
OPERATION OF REMOTE CONTROL UNIT .................11
GENERAL INFORMATION OF RC5001SR TO SR6001..
12
CONTROLLING MARANTZ COMPONENTS .................13
BASIC OPERATION.........................................................15
CONNECTIONS ...................................17
SPEAKER PLACEMENT .................................................17
CONNECTING SPEAKERS.............................................17
CONNECTING AUDIO COMPONENTS..........................18
CONNECTING VIDEO COMPONENTS..........................20
ADVANCED CONNECTING ............................................21
CONNECTING THE REMOTE CONTROL JACKS.........21
CONNECTING THE ANTENNA TERMINALS.................22
XM RADIO OVERVIEW ...................................................23
CONNECTING THE XM CONNECT-AND-PLAY
ANTENNA.........................................................................23
CONNECTING FOR THE MULTI ROOM ........................24
CONNECTING OTHER EQUIPMENT.............................25
BASIC OPERATION (TUNER).............53
LISTENING TO THE TUNER...........................................53
PRESET MEMORY ..........................................................54
LISTENING TO XM SATELLITE RADIO..........................56
SEARCH MODE...............................................................57
PRESET MEMORY ..........................................................58
MULTI ROOM SYSTEM .......................60
MULTI ROOM PLAYBACK USING THE MULTI ROOM
OUT TERMINALS.............................................................60
MULTI ROOM PLAYBACK USING THE MULTI SPEAKER
TERMINALS .....................................................................60
OPERATION OF THE MULTI ROOM OUTPUTS WITH
THE REMOTE CONTROL FROM MULTI ROOM ...........61
TROUBLESHOOTING .........................62
HDMI.................................................................................63
TROUBLESHOOTING .....................................................63
TECHNICAL SPECIFICATIONS..........64
DIMENSIONS ......................................64
SR6001UDFU1ENG14.indd1SR6001UDFU1ENG14.indd1 06.12.214:13:54PM06.12.214:13:54PM
ENGLISH
2
DESCRIPTION
DTS was introduced in 1994 to provide 5.1 channels
of discrete digital audio into home theater systems.
DTSbringsyou premiumquality discretemultichannel
digital sound to both movies and music.
DTS is a multichannel sound system designed to
create full range digital sound reproduction.
The no compromise DTS digital process sets the
standard of quality for cinema sound by delivering
an exact copy of the studio master recordings to
neighborhood and home theaters.
Now, every moviegoer can hear the sound exactly as
the moviemaker intended.
DTS can be enjoyed in the home for either movies or
music on of DVD’s, LD’s, and CD’s.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
The advantages of discrete multichannel systems
over matrix are well known.
Butevenin homes equippedfordiscretemultichannel,
there remains a need for high-quality matrix decoding.
This is because of the large library of matrix surround
motion pictures available on disc and on VHS tape;
and analog television broadcasts.
The typical matrix decoder of today derives a center
channel and a mono surround channel from two-
channel matrix stereo material. It is better than a
simple matrix in that it includes steering logic to
improve separation, but because of its mono, band-
limited surround it can be disappointing to users
accustomed to discrete multichannel.
Neo:6 offers several important improvements as
follow,
• Neo:6 provides up to six full-band channels of
matrix decoding from stereo matrix material. Users
with 6.1 and 5.1 systems will derive six and five
separate channels, respectively, corresponding to
the standard home-theater speaker layouts.
• Neo:6 technology allows various sound elements
within a channel or channels to be steered
separately, and in a way which follows naturally
from the original presentation.
• Neo:6 offers a music mode to expand stereo
nonmatrix recordings into the five- or six-channel
layout, in a way which does not diminish the subtlety
and integrity of the original stereo recording.
DTS-ES Extended Surround is a new multichannel
digital signal format developed by Digital Theater
Systems Inc. While offering high compatibility with
the conventional DTS Digital Surround format, DTS-
ES Extended Surround greatly improves the 360-
degree surround impression and space expression
thanks to further expanded surround signals. This
format has been used professionally in movie
theaters since 1999.
In addition to the 5.1 surround channels (FL, FR, C,
SL, SR and LFE), DTS-ES Extended Surround also
offers the SB (Surround Back) channel for surround
playback with a total of 6.1 channels. DTS-ES
Extended Surround includes two signal formats with
different surround signal recording methods, as DTS-
ES Discrete 6.1 and DTS-ES Matrix 6.1.
“DTS”, “DTS-ES and “Neo:6” are trademarks of
Digital Theater Systems, Inc.
The stereo CD is a 16-bit medium with sampling at
44.1 kHz. Professional audio has been 20- or 24-
bit for some time, and there is increasing interest
in higher sampling rates both for recording and for
delivery into the home. Greater bit depths provide
extended dynamic range. Higher sampling rates
allow wider frequency response and the use of anti-
alias and reconstruction filters with more favorable
aural characteristics.
DTS 96/24 allows for 5.1channel sound tracks to be
encoded at a rate of 96kHz/24bits on DVD-Video
titles.
When DVD-video appeared, it became possible to
deliver 24-bit, 96 kHz audio into the home, but only in
two channels, and with serious limitations on picture.
This capability has had little use.
DVD-audio allows 96/24 in six channels, but a
new player is needed, and only analog outputs are
provided, necessitating the use of the D/A converters
and analog electronics provided in the player.
INTRODUCTION
Thank you for purchasing the Marantz SR6001
Surround receiver.
This remarkable component has been engineered
to provide you with many years of home theater
enjoyment. Please take a few minutes to read this
manual thoroughly before you connect and operate
the SR6001.
Asthereare a numberof connectionandconfiguration
options, you are encouraged to discuss your own
particular home theater setup with your Marantz A/V
specialist dealer.
XM Satellite Radio Ready
The XM name and related logos are registered
trademarks of XM Satellite Radio Inc.
PRECAUTIONS
DO NOT LOCATE IN THE FOLLOWING PLACES
To ensure long-lasting use, do not locate the SR6001
where it is:
• Exposed to direct sunlight.
• Near sources of heat such as heaters.
•
In highly humid or poorly ventilated environments.
• Dusty.
• Subjected to mechanical vibrations.
• On wobbly, inclined or otherwise unstable
surfaces.
• In locations such as in cramped audio racks
where radiated heat is blocked.To ensure proper
heat radiation, ensure the below clearance from
walls and other equipment.
DIGITAL
RLVIDEO
S-VIDEO
AUX1INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
INPUTSELECTOR
AVSURROUNDRECEIVER SR6001
MultEQ
ENTER
HT-EQ
PUREDIRECT THX
7.1CHINPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PUREDIRECT
SURROUND
SPEAKER
MULTI
DSD
POWERON/STANDBY
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V-OFFDISP MULTI AUTO TUNED ST SPKRAB
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP SURR DIRECT
AUTO DISC6.1 MTX 6.1 EQ
PCM
AAC
READY
Left
8 inchs (20 cm)
or more
Above
8 inchs (20 cm)
or more
Right
8 inchs (20 cm)
or more
Rear
8 inchs (20 cm)
or more
SR6001UDFU1ENG14.indd2SR6001UDFU1ENG14.indd2 06.12.214:13:56PM06.12.214:13:56PM
ENGLISH
3
About Dolby Pro Logic II x
Dolby Pro Logic IIx technology delivers a natural
and immersing 7.1-channel listening experience
to the home theater environment. A product of
Dolby's expertise in surround sound and matrix
decoding technologies, Dolby Pro Logic IIx is a
complete surround sound solution that maximizes
the entertainment experience from stereo as well as
5.1-channel encoded sources.
Dolby Pro Logic IIx is fully compatible with Dolby
Surround Pro Logic technology and can optimally
decode the thousands of commercially available
Dolby Surround encoded video cassettes and
television programs with enhanced depth and
spatiality. It can also process any high-quality
stereo or Advanced Resolution 5.1-channel music
content into a seamless 6.1- or 7.1-channel listening
experience.
The Dolby Headphone technology provides a
surround
sound listening experience over headphones.
When listening to multichannel content such as DVD
movies over headphones, the listening experience
is fundamentally different than listening to speakers.
Since the headphone speaker drivers are covering
the pinna of the ear, the listening experience differs
greatly from traditional speaker playback. Dolby
utilizes patented headphone perspective curves to
solve this problem and provides a non-fatiguing,
immersive, home theater listening experience. Dolby
Headphone also delivers exceptional 3D audio from
stereo material.
Dolby Virtual Speaker is a technologycertified
by Dolby Laboratories that creates a virtualized
surround sound experience from two speakers using
a multichannel Dolby Digital source. Additionally,
Dolby Virtual Speaker can simulate the surround
sound effect produced by Dolby Pro Logic or Dolby
Pro Logic II.
Dolby Virtual Speaker retains all the original
Multichannel audio information and provides the
listener with the sensation of being surrounded by
additional speakers.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Circle Surround II (CS-II) is a powerful and versatile
multichannel technology. CS-II is designed to enable
up to 6.1 multichannel surround sound playback
from mono, stereo, CS encoded sources and other
matrix encoded sources. In all cases the decoder
extends it into 6 channels of surround audio and a
LFE/subwoofer signal. The CS-II decoder creates a
listening environment that places the listener “inside”
music performances and dramatically improves
both hi-fi audio conventional surround-encoded
video material. CS-II provides composite stereo rear
channels to greatly improve separation and image
positioning– adding a heightened sense of realism to
both audio and A/V productions.
CS-II is packed with other useful feature like dialog
clarity (SRS Dialog) for movies and cinema-like bass
enrichment (TruBass). CS-II can enable the dialog
to become clearer and more discernable in movies
and it enables the bass frequencies contained in the
original programming to more closely achieve low
frequencies–overcoming the low frequency limitations
of the speakers by full octave.
Circle Surround II, Dialog Clarity, TruBass, SRS and
symbol are trademarks of SRS Labs, Inc.
Circle Surround II , Dialog Clarity and TruBass
technology are incorporated under license from SRS
Labs, Inc.
HDCD®(High Definition Compatible Digital ®) is a
patented process for delivering on Compact Disc the
full richness and details of the original microphone
feed.
HDCD encoded CDs sound better because they are
encoded with 20-bits of real musical information as
compared to 16-bits for all other CDs.
HDCD overcomes the limitation of the 16-bit CD
format by using a sophisticated system to encode
the additional four bits onto the CD while remaining
completely compatible with the CD format.
When listening to HDCD recordings, you hear more
dynamic range, a focused 3-D sound stage, and
extremely natural vocal and musical timbre. With
HDCD, you get the body, depth and emotion of the
original performance not a flat, digital imitation.
HDCD system manufactured under license from
Microsoft. This product is covered by one or more
of the following: In the United States 5,479,168
5,638,074 5,640,161 5,808,574 5,838,274 5,854,600
5,864,311 5,872,531 and in Australia 669,114 with
other patents pending.
HDMI, the and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
DTS 96/24 offers the following:
1. Sound quality transparent to the original 96/24
master.
2. Full backward compatibility with all existing
decoders. (Existing decoders will output a 48 kHz
signal)
3. No new player required: DTS 96/24 can be carried
on DVD-video, or in the video zone of DVD-audio,
accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality full-
motion video, for music programs and motion
picture soundtracks on DVD-video.
“DTS” and “DTS 96/24” are trademarks of Digital
Theater Systems, Inc.
Dolby Digital identifies the use of Dolby Digital audio
coding for such consumer formats as DVD and DTV.
As with film sound, Dolby Digital can provide up
to five full-range channels for left, center, and right
screen channels, independent left and right surround
channels, and a sixth (“.1”) channel for low-frequency
effects.
Dolby Surround Pro Logic
II
is an improved matrix
decoding technology that provides better spatiality
and directionality on Dolby Surround program
material; provides a convincing three-dimensional
soundfield on conventional stereo music recordings;
and is ideally suited to bring the surround experience
to automotive sound. While conventional surround
programming is fully compatible with Dolby Surround
Pro Logic
II
decoders, soundtracks will be able to be
encoded specifically to take full advantage of Pro
Logic
II
playback, including separate left and right
surround channels. (Such material is also compatible
with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output
channels from 5.1-channel sources. This is done
using a matrix decoder that derives three surround
channels from the two in the original recording. For
best results, Dolby Digital EX should be used with
movies soundtracks recorded with Dolby Digital
Surround EX.
SR6001UDFU1ENG14.indd3SR6001UDFU1ENG14.indd3 06.12.214:13:56PM06.12.214:13:56PM
ENGLISH
4
There are several factors that can degrade the sound
from even the best loudspeakers in a listening room.
One of the most important is the interaction of sound
from the loudspeakers with large surfaces such as
walls, the floor, and the ceiling in the room. Even
with careful loudspeaker placement and acoustical
treatments, there are significant problems that are
caused by room acoustics.These include reflections
from nearby surfaces and standing waves that are
created between large parallel surfaces in the room.
In a home theater the situation is further complicated
because there are several listening locations. The
effects of room acoustics on the sound arriving at
each person’s ears are very different and the result is
a listening experience that is degraded in a different
way for every person in the room. It is not uncommon
to have variations in two adjacent seats that are as
large as 10 dB, particularly in the frequency range
below 250 Hz.
The solution to this problem is to apply room correction
after precisely measuring how each loudspeaker
interacts with the room. Because the room causes
variations in the frequency response of the
loudspeakers that are so large from seat to seat, it
is important to measure each loudspeaker at several
locations in the listening room. This should be done
even if there is only one listener. Measurement at a
single location is not representative of the acoustical
problems in the room and will in most cases, degrade
overall performance. Audyssey MultEQ is the only
technology that can achieve room correction for
multiple listeners in a large listening area. It does so
by combining the data collected at several points in
the room from each loudspeaker and then applying
correction that minimizes the acoustical effects of
the room and is matched to the frequency resolution
of human perception (known as psychoacoustics).
Furthermore, MultEQ correction is applied both
in frequency and time domains and so there are
no artifacts (such as smearing of sound or modal
ringing)that are sometimes associated with traditional
methods of room equalization.
Inadditiontocorrecting frequencyresponseproblems
over a wide listening area, Audyssey MultEQ
provides a completely automated sound system
set-up process. It identifies how many loudspeakers
are connected to the amplifiers and whether they
are full-range, satellites, or subwoofers. If there is a
least one subwoofer connected, Audyssey MultEQ
determines the optimum crossover frequency
between each satellite and the subwoofer(s). It
automaticallychecks thepolarity ofeach loudspeaker
and alerts the user if there are any that may be wired
out-of-phase relative to the others. It measures the
distance to each loudspeaker from the main listening
position and adjusts the delays so that sound from
each loudspeaker arrives at the same time. Finally,
Audyssey MuitEQ determines the playback level of
each loudspeaker and adjusts the volume trims so
that all levels are equal.
MultEQ and the Audyssey MultEQ logo are
trademarks of Audyssey Laboratories, Inc. All rights
reserved.
SR6001UDFU1ENG14.indd4SR6001UDFU1ENG14.indd4 06.12.214:13:56PM06.12.214:13:56PM
ENGLISH
5
FEATURES
The SR6001 incorporates the latest generation of
digital surround sound decoding technology such as
Dolby Digital EX, Dolby Digital, DTS ES (Discrete 6.1
and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby
Pro-Logic II (Movie, Music and Game), Dolby Pro-
Logic IIx (Movie, Music and Game), Circle Surround
II (Cinema, Music and Mono).
In addition, Marantz has focused on the future. By
utilizing pre-out jacks, 7.1 direct inputs and a RS-
232C communication port, the SR6001 is tomorrow’s
technology, today!
The SR6001 incorporates the most advanced
Digital Signal Processing circuitry, along with a 192
kHz/24 bit D/A converter in each of the 7 channels.
Independentpowersupplycircuitsareincorporatedfor
the FL display, audio and video sections for maximum
separation, clarity and dynamic range. Together with
hand-selected customized components, all elements
work in harmony to recreate the emotion, exactly as
the artist had intended.
The SR6001 is designed and engineered with
extensive feedback from custom installation experts,
dealers and consumers. It features multi-room/
multisource, assignable DC trigger, a RS-232C
communication port, Flasher input, heavy duty
speaker binding posts and an extensive array of both
analog and digital inputs / outputs.With 5 assignable
digital inputs (6 total), 4 component inputs, Super
Audio CD Multi Channel (7.1 channel) direct inputs,
video convert system and a speaker-B and OSD
output versatility is taken to a stunning new level.
Furthermore, the SR6001 can output the OSD
information through the Y/C (S-video) and composite
video outputs.
An easy-to-use programmable, learning remote
control allows full access to all of the operating
functions and can be used for system operation as
well.
The new generation of Marantz Receivers is stylish
and completely symmetrical. On the front panel of
the SR6001, buttons are kept to a minimum. Source
selectors and volume controls are intuitively placed.
The SR6001 is here to perform in your unrivaled home
entertainment setup.
• HDMI
HDMI (High-Definition Multimedia Interface) is an
enhancement to the DVI (Digital Visual Interface)
standard. It adds capabilities for digitally transmitting
audio signals in addition to video signals. Where
multiple cables were previously needed for audio/
video, HDMI enables audio/video connection via a
single cable.
The HDMI input jacks of this receiver support HDMI
Ver.1.2.and the HDMI output jacks of this transmitter
support HDMI Ver. 1.1.
Ver. 1.2 supports 1-bit audio formatting and enables
transmission of DSD (Direct Stream Digital) signals
of Super Audio CD.
Copyright Protection
This receiver supports HDCP (High-bandwidth Digital
Content Protection). HDCP is copyright protection
technology that consists of data encoding and other
device authentication. Its purpose is to protect digital
video content. Both this receiver and the connected
component (such as a video player or monitor) must
support HDCP. Before connecting a component to
this receiver, refer to its instruction manual.
• Dolby Digital EX, Dolby Digital, DTS ES
(Discrete 6.1, Matrix 6.1, Neo:6)
• Dolby Pro Logic II (Movie, Music, Game)
• Dolby Pro Logic II x (Movie, Music, Game)
• Circle Surround II (Cinema, Music, Mono)
• Audyssey Mult EQ
• 7 ×100 Watts (8 Ohms), Discrete Amplifiers
• High Power Current Feedback Circuitry
• Massive Energy Power Supply, Huge EI
Transformer, Large ELCO’s.
• 192 kHz/24 bit DAC for all 8 Channels
• 32 bit Digital Surround Processing Chipsets
• Video Off Mode
• Large Heavy Duty Speaker Terminals for all
Channels
• RS-232C Terminal for Future Upgrade or System
Control
•
Set Up Menu via all Video Output
(Composite, S-Video, Component video and
HDMI)
• Auto Input Signal Detection
• Improved Station Name Input Method, 60 Presets
• Auto Adjust Function for Speaker Distance Settings
(Delay Time)
• Front Optical AUX Input
(Digital Camera, Portable DVD)
• Programmable, learning remote control
• Video convert system
HDMI ←Component Video ↔
S-Video ↔Composit Video
• Video I/P Converter
• Assignable Video Input
• Lip Sync (Audio Delay)
FM Antenna
Front AUX Jack Cover
PUSH
PUSH
User Guide
Warranty Card
USA ×1
Canada ×1
• Function Rename
• HDCD
• Dolby Headphone
• Bi-amp drive
• Source/Pure Direct mode
• 9 bands x 7 ch GEQ
• DSD direct conversion
• DSD to PCM converter
• Assignable DC Trigger Output
• Flasher Input
ACCESSORIES
Remote Controller RC5001SR
SYSTEM REMOTECONTROLLER
RC5500SR
EXIT
SETUP/
MENU
OSD
ENTER
7.1CHIN
A/D
HT-EQ
P.SCAN
STEREO
NIGHT
M-CHST
CSII
EX/ES
VIRTUAL
T.MODE
INPUT
LIPSYNC/
dts
AITP
MULTI/CAT
M-SPKR
SPKRA/B
MUTE
TREBLE
BASS
CH-SEL
V-OFFATT.
AUDIO
SUBTITLE
DISC+ANGLE
3
BAND
2
1
64
5
4
94
8
7
+10
MEMO
0
CL
DSS
VCR
DVD
TV
F.DIRECT
PTY
T.DISP
BASS
TUNING
PRESET
T.TONE
CH/CAT VOLLUME
OFF
ON
SOURCE
SURROUND
P.DIRECT
DISPLAY
SLEEP
SET
LEARN SEND
TAPE AUX1 AUX2 AMP
TUNER CD CDR MD
l/l/
AAA-size batteries × 2
AC cable
AM Loop Antenna
SR6001UDFU1ENG14.indd5SR6001UDFU1ENG14.indd5 06.12.214:13:57PM06.12.214:13:57PM
ENGLISH
6
rSURROUND MODE button
You can select the surround mode by pressing this
button.
tAUTO (Auto surround) button
Press this button to select the AUTO mode from
the surround modes. When this mode is selected,
the receiver determines the surround mode
corresponding to a digital input signal automatically.
yMULTI (Multi Room) button
Press this button to activate the Multiroom system.
“MULTI” indicator will be illuminated in the display.
(See page 60)
uMULTI SPEAKER button
Press this button to activate the Multiroom Speaker
system. “MULTI” indicator will be illuminated in the
display.
(See page 60)
iBAND button
Press this button to switch between FM and AM in
the TUNER mode.
oT-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
(See page 53)
qPOWER switch and STANDBY
indicator
When this switch is pressed once, the unit turns ON
and the display illuminates. When pressed again, the
unit turns OFF and the STANDBY indicator will be
illuminated.
wINPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources.
Note:
• When the input source is set to TUNER, it is possible
to select the video source separately.
e
HEADPHONE jack for stereo headphones
This jack may be used to listen to the SR6001’s
output through a pair of headphones. Be certain
that the headphones have a standard 1/4” stereo
phono plug. Note that the main room speakers will
automatically be turned off when the headphone
jack is in use.
Notes:
• When using headphones, the surround mode will
change to STEREO and Dolby Headphone by
MENU and Cursor button.
• The surround mode returns to the previous setting
as soon as the headphone plug is removed from the
jack.
!0 MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 54)
!1 CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 55)
!2
INFRARED receiving sensor window
This window receives infrared signals for the remote
control.
!3 VOLUME control knob
Adjusts the overall sound level. Turning the control
clockwise increases the sound level.
!4 AUX1 INPUT jacks
These auxiliary video/audio input jacks accept the
connections of a camcorder, portable DVD, game
etc. When not using these jacks, protect with the
included jack covers.
How to Attach the Front AUX Jack Cover
AUX 1 INPUT
AUDIO
S-VIDEO
DIGITALVIDEOLR
UP
PUSH
PUSH
Front AUX Jack Cover
!5
PURE DIRECT button and indicator
When this button is pressed once, “SOURCE
DIRECT” appears on the FL display. If pressed again,
“PURE DIRECT” appears. After 2 seconds, the FL
display indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct function is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
!6 HT-EQ button
Press this button to switch between HT-EQ ON/Off.
!7 7.1CH INPUT button
Press this button to select the output of an external
multichannel player.
!8 MENU button
This button is used to enter the SETUP MAIN
MENU.
!9
Cursor (
5, ∞, 2, 3
) / ENTER button
Use these buttons when operating the SETUP MAIN
MENU and TUNER function.
@0 EXIT button
This button is used to exit from the SETUP MAIN
MENU.
@1 DISPLAY button
When this button is pressed, the FL display mode
is changed as Input display →Surround Mode →
Auto-display Off →Display Off →Function name
display and the display off indicator (DISP) lights up
is condition DISPLAY OFF.
@2 MultEQ button / MIC jack
Presstoautomaticallymeasurespeakercharacteristics
using the microphone. (See page 32)
Note:
• A special microphone (option) is needed to use the
MultiEQ function. (See page 32)
@3 SPEAKER A/B button
Press this button to select speaker systems A and/or
B.
FRONT PANEL
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MultEQ
ENTER
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/STANDBY
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V-OF FDISP MULTI AUTO TUNED ST SPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP SURR DIRECT
AUTO DISC 6.1 MT X 6.1 EQ
PCM
AAC
READY
!8 @0 @2!9
q tyur !2 !3 !4ew
!5 !6 !7 @1 @3
io!0!1
SR6001UDFU1ENG14.indd6SR6001UDFU1ENG14.indd6 06.12.214:13:57PM06.12.214:13:57PM
ENGLISH
7
FL DISPLAY AND INDICATOR
DISP MULTI AUTO TUNED ST V
–
OFF NIGHT PEAK ANALOG
DIGITAL
ATT
EQ
SLEEP SURR
AUTO DISC 6.1DIRECT MTX 6.1 SPKR AB
DIGITAL
SURROUND
PCM
L
C
R
SL S SR
LFE
¡
6
g
s
a
¡
7
™
0
™
1
¡
8
¡
5
hk¡0 ¡1 ¡3f
jl ¡2 ¡4d
¡
9
™
2
aDISP (Display Off) indicator
This indicator is illuminated when the SR6001 is in
the display off condition.
sSLEEP timer indicator
This indicator is illuminated when the sleep timer
function in the main-room is in use.
dMulti-room system indicator
This indicator is illuminated when the multi-room
system is active.
fAUTO SURR
(Auto Surround mode) indicator
This indicator is illuminated to show that the AUTO
SURROUND mode is in use.
gTUNER’s indicators
AUTO : This indicator illuminates when the
tuner’s Auto mode is in use.
TUNED : This indicator illuminates when
a station is being received with
sufficient signal strength to provide
acceptable listening quality.
ST(Stereo) : This indicator illuminates when an
FM station is being tuned into stereo
condition.
h
DTS-ES mode indicators (DISC6.1, MTX6.1)
These indicators will illuminate to show the DTS-ES
decoding mode (Discrete 6.1 or Matrix 6.1).
jV (video)-OFF mode indicator
This indicator is illuminated when the Video-OFF
function is active.
kNIGHT mode indicator
This indicator is illuminated when the SR6001 is in
the Night mode, which reduces the dynamic range of
digital program material at low volume levels.
lSPKR (speaker) AB indicator
Active speaker system will be illuminated by this
indicator.
¡0 PEAK indicator
This indicator is a monitor for an analog audio input
signal. If the selected analog audio input signal is
greater than the capable level of internal processing,
this will illuminate. If this happens, you should press
the ATT button on the remote. (See page 10)
¡1 ATT (Attenuation) indicator
This indicator is illuminated when the attenuation
function is active.
¡2 DIGITAL Input Indicator
This indicator lights when a digital input has been
selected.
¡3 ANALOG input indicator
This indicator is illuminated when an analog input
source has been selected.
¡4 SIGNAL FORMAT indicators
2DIGITAL
This indicator is illuminated when a Dolby Digital
signal is input.
EX
This indicator is illuminated when a Dolby Digital EX
signal is input.
dts
This indicator is illuminated when a DTS signal is
input.
ES
This indicator is illuminated when a DTS ES signal
is input.
96/24
This indicator is illuminated when a DTS 96/24 signal
is input.
PCM
This indicator is illuminated when the input signal is
PCM (pulse code modulation).
2SURROUND
This indicator is illuminated when a Dolby Surround
signal is input.
¡5
ENCODED CHANNEL STATUS indicators
These indicators display the channels that are
encoded with a digital
input signal. If the selected digital input signal is
Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”,
“SR” and “LFE” will be illuminated.If the digital input
signal is 2 channel PCM-audio, “L” and “R” will be
displayed.
If Dolby Digital 5.1ch signal with Surround EX flag
or DTS-ES signal comes in, “L”, “C”, “R”, “SL”, “S” ,
“SR” and “LFE” will be illuminated.
¡6 Main Information Display
This display shows messages relating to the status,
input source, surround mode, tuner, volume level or
other aspects of unit’s operation.
¡7 SOURCE DIRECT indicator
This indicator is illuminated when the SR6001 is in
the SOURCE DIRECT mode.
¡8 DSD indicator
This indicator illuminates when a DSD (Direct Stream
Digital) signal of an Super Audio CD is input via the
audio signal included in the HDMI input signal.
¡9 PURE DIRECT indicator
This indicator is illuminated when the SR6001 is in
the PURE DIRECT mode.
™0 HDCD indicator
When HDCD signal is decoded, this indicator will
light up.
™1 HDMI indicator
This indicator illuminates when an HDMI device is
connected to the input and a link is established.
™2 EQ indicator
This indicator is illuminated when the EQ MODE is
selected to “AUDDYSSEY”, “FRONT” or “FLAT”.
Opening and closing the front panel door
When you want to use the controls behind the front
panel door, open the door by gently pressing on the
lower part of the panel. Keep the door closed when
not using these controls.
AVSURROUND RECEIVER SR6001
PHONES
STANDBY
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
DISPMULTIAUTO TUNEDSTSPKRAB V-OFF
NIGHT
PEAKANALOG
DIGITAL
ATT
SLEEPSURRDIRECT
AUTODISC6.1MTX6.1
PCM
AAC
AUX1INPUT
AUDIO
S-VIDEO
DIGITALVIDEOLR
ENTER
DOWN
UP
VOLUME
POWERON/OFF
INPUTSELECTOR
READY
Caution:
• Be careful not to pinch your fingers between the
door and the panel.
SR6001UDFU1ENG14.indd7SR6001UDFU1ENG14.indd7 06.12.214:13:57PM06.12.214:13:57PM
ENGLISH
8
uSpeaker outputs terminals
(SURROUND BACK / MULTI
SPEAKER / SPEAKER C)
Two terminals are provided for the front left, and
right speakers for multi room (2nd zone) or surround
back.
The terminals can be used to connect a third set of
speakers by setting the SPEAKER C selector switch
to ON. For connection and use, see page 24.
iSpeaker outputs terminals
Seven terminals are provided for the front (A) left,
front (A) right, front (B) left, front (B) right, front center,
surround left, and surround right speakers.
oSPEAKER C switch
Set to ON to connect a bi-amp to this receiver or set
to OFF for normal speaker connection (surround
back and multiroom speakers). (See page 24)
!0 AC OUTLETS
Connect the AC power cables of components such as
a DVD and CD player to these outlets. SWITCHED and
UNSWITCHED outlets are provided.
The one marked SWITCHED provides power only
when the SR6001 is turned on and is useful for
components which you use every time you play your
system.
The one marked UNSWITCHED is always live as
long as the SR6001 is plugged into a live outlet.
A component connected here may be left on
permanently, or may be switched off with via its own
power switch.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into these outlets should be powered up
before the SR6001 is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more than
the capacity of these AC outlets. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
!1 AC INLET
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
SR6001 can be powered by 120V AC only.
!2 Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L (front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifiers.
!3 Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifier is used,
connect this jack to the subwoofer amplifier input.
If you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifier, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifier.
!4 7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!5
FLASHER IN (Flasher input terminal)
These terminals are to control the unit from each zone.
Connect the control signal from a Keypad, etc.
!6 DC TRIGGER output terminal
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
• This output voltage is for (status) control only, It is
not sufficient for drive capability.
!7
MULTI ROOM REMOTE IN/OUT terminals
IN: Connect to a multi-room remote control
device, available from your Marantz dealer.
OUT: Connect to the Marantz component equipped
with remote control (RC-5) terminals in Multi
zone (Multi room).
!8 REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
REAR PANEL
eMultiroom Output (Audio output)
This is the audio output jack for the Multi zone (Multi
room).
Connectthese jackstooptional audiopoweramplifiers
to listen the source selected by the multiroom system
in a remote room.
rMONITOR OUT
These are monitor outputs and each one includes
both composite video and S-video configurations.
When connecting two video monitors or televisions,
be aware that the OSD interface can be used with
both MONITOR OUT connections.
tRS-232C
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
SR6001 by using an external device.
The RS-232C port may also be used in the future to
update the operating software of the SR6001 so that
it will be able to support new digital audio formats and
the like as they are introduced.
yXM terminal
See page 23 for connecting information.
qFM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”.The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
wCOMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the SR6001. The
SR6001 has 4 component video input connectors to
obtain the color information (Y, CB, CR) directly from
the recorded DVD signal or other video component,
and 1 component video output connector to output
the information directly into the matrix decoder of the
display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image.The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
FM (75)GND AM
DC OUT
OUTPUT
COMPONENT
VIDEO
IN OUT
PRE
OUT
SLL
RSR
FLASHER
IN
SPEAKER
SYSTEMS
INPUT 1(DVD)
COAX.
DIGITALIN
DIGITALOUT
3
54
21
SURROUND
BACK
OUT
R
OUT
L
RS-232C
OUTPUT
TAPE CD/CD-R
OUTOUTIN
MULTI
R
L
DSS
(AUX2)
AUDIO
TV
7.1CH
IN
IN
OPT.
DVD(2)DSS(4)
TV(1)
VIDEO
OUT
VCR(3)
OUTIN
RC-5 MULTI RC
INPUT 1(TV)
INPUT 4(DSS)
IN
SR
VCR
IN
INPUT 3(VCR)
DVD SL
INPUT 2(DSS)
ANTENNA
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
YYY
DVD(2)
DSS(4)
VCR(3)
TV(1)MONI. OUT
MONITOR
OUT
SBR
SBL
SBR
SBL
C
SW
SW
C
R
L
R
R
R
L
LL
AC IN
INPUT 2(DVD)
S-VIDEO
MODEL NO. SR6001
FRONT
B
SURR
OUND
CEN
TER
FRONT
A
ON
OFF
MULTI SPEAKER
/
SPEAKER C
FRONT A OR B.CENTER.SURR.
SURR BACK : 6 - 8 OHMS
FRONT A + B : 8 OHMS
HDMI
Ver1.2
UNSWITCHED
1.25A 150W
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
XM
rq tw uyi
o!0!1!2!4
!7!8
@1
@2
!3
@0
!9
e
!6 !5
SR6001UDFU1ENG14.indd8SR6001UDFU1ENG14.indd8 06.12.214:13:58PM06.12.214:13:58PM
ENGLISH
9
!9 AUDIO IN/OUT (TV, DVD, VCR,
DSS, TAPE, CD/CDR)
These are the analog audio inputs and outputs.
There are 6 audio inputs and 3 audio outputs. The
audio jacks are nominally labeled for cassette tape
decks, compact disc players, DVD players and etc....
The audio inputs and outputs require RCA-type
connectors.
@0 DIGITAL INPUT (Dig.1 - 5) /
OUTPUT (coaxial, optical)
These are the digital audio inputs and outputs.There
are 2 digital inputs with coaxial jacks, 3 with optical
jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other similar
components.
@1
VIDEO IN/OUT
(TV, DVD, VCR, DSS)
These are the video inputs and outputs. There
are 4 video inputs and 1 video output and each
one includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 1 video output channel can be used to connected
to video tape recorders for making recordings.
@2 HDMI INPUT / OUTPUT
This unit has 2 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 19)
9/NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This function
reduces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
0/7.1CH IN button
Press this button to select the output of an external
multi channel decoder.
(+10) A/D button
Used to switch between the analog and digital
inputs.
mCL (Clear) button
This button is used to erase the memory or program
of a source.
,SPKR A/B button
Used to select the speaker system.
The speaker system is switched in the following
sequence.
A →B →A+B →off
.CH/CAT3(UP) / 4(DOWN) buttons
These buttons are used to change channels.
⁄0 MULTI/CAT button
(When AMP mode is selected)
Used to turn on and off multi room.
⁄1 INFO button
(When AMP mode is selected)
When this button is pressed, the current setting are
displayed on the TV monitor.
⁄2 T.TONE/SET UP button
(When AMP mode is selected)
Used to enter the test tone menu.
REMOTE CONTROL
OPERATION
FUNCTION AND OPERATION
The provided remote control unit is a universal
remote controller. The POWER button, numeric
buttons and control buttons are used in common
across different input source components.
The input source controlled with the remote control
unit changes when one of the input selector buttons
is pressed.
zLEARN indicator
Indicates when the remote controller is in the LEARN
mode.
xSET button
This button is used to enter learn mode and preset
mode.
c/ SOURCE ON/OFF button
This button is used to turn a specific source (such as
a DVD player) on or off independently from the rest
of the system.
vSLEEP button
This button is used for setting the sleep timer.
bDISPLAY button
Selects the display mode for the front display of the
SR6001.
nNumeric buttons
These buttons are used to switch between 0 to +10
of the source components.
If the source is set to the amplifier, these buttons are
used to perform operations.
(When AMP mode is selected)
1/AUTO button
Used to select auto surround.
2/Dolby button
Used to select DOLBY mode.
3/dts button
Used to select dts mode.
4/CSII button
Used to select CSII mode.
5/EX/ES button
Used to select EX/ES mode.
6/VIRTUAL button
Used to select VIRTUAL mode.
7/M-CH ST button
Used to select Multi Channel Stereo.
8/STEREO button
Used to select STEREO mode.
TAP E
CAT
P.SCAN
CAT
T.MODE
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
123
456
789
0
+10
REMOTE CONTROLLER
RC5001SR
HT-EQ
MULTI/
SEND
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
INPUT
T.TONE
/SET UP
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
EX/ES
VIRTUAL
CS
VOLUME
BASS
TREBLE
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
A/D
LEARN
LIP SYNC/
MEMO
BAND
CL
SOURCE
z
m
.
⁄1
⁄2
⁄3
⁄6
⁄5
c
v
x
‹0
n
b
,
⁄0
⁄4
¤9
¤8
‹4
¤6
¤4
¤3
‹5
¤2
¤0
¤1
⁄7
⁄9
‹2
‹3
‹1
⁄8
¤5
¤7
SR6001UDFU1ENG14.indd9SR6001UDFU1ENG14.indd9 06.12.214:13:58PM06.12.214:13:58PM
ENGLISH
10
⁄3 CONTROL buttons
These buttons are used when operating PLAY, STOP,
PAUSE and other commands of a source.
(When TUNER mode is selected)
T.DISP button
Used to select the display mode in RDS.
PTY button
Used to display the programme type information of
the current station.
F.DIRECT button
Used to select the "Frequency direct input".
PRESET +/- buttons
Used to select a preset station up and down.
TUNING +/- buttons
Used to tune a frequency station up and down.
⁄4 ANGLE/V-OFF buton
(When AMP mode is selected)
Used to turn off the video signal.
⁄5 DISC+/CH. SEL button
(When AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust
speaker levels or 7.1 ch input level.
⁄6 BASS +/- buttons
These buttons are used to adjust the tone control
of low frequency sound for left, right and subwoofer
speaker.
⁄7 SEND indicator
Indicates when the remote controller is transmitting
a signal.
⁄8 / POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the SR6001 on or
off.
⁄9 SURROUND button
This button is used to selects the surround mode.
¤0 P.DIRECT button
When this button is pressed, the tone control circuit
is bypassed.
¤1 BAND/LIP SYNC/INPUT button
(When TUNER mode is selected)
Used to select a radio band.
(When AMP mode is selected)
Used to select LIP SYNC mode.
(When TV mode is selected)
Used to select monitor input.
¤2 T.MODE button
(When TUNER mode is selected)
Used to select auto stereo mode or mono mode
when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
¤3 P.SCAN button
(When TUNER mode is selected)
Used to start preset scan.
¤4 MEMO/HT-EQ button
This button is used to store setting to memory or
program a source.
(When AMP mode is selected)
Used to turn on or off HT(Home Theater)-EQ mode.
This mode compensates for the audio portion of a
movie sounding “bright”.
¤5 MUTE button
This button is used to mute the audio for the amplifier
and television.
Note:
Set the AMP mode to use this button with the
SR6001.
¤6 VOLUME +/- buttons
This button is used to adjust the volume for the
amplifier and television.
Note:
Set the AMP mode to use this button with the
SR6001.
¤7 M-SPKR button
(When AMP mode is selected)
Used to turn on and off multi speaker.
¤8 MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN
MENU of the SR6001.
¤9 1,
2,
3,
4
(CURSOR) / ENTER
buttons
These buttons are used when controlling the cursor
of the SR6001, DVD or other AV equipment.
‹0 EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup
menu.
‹1 SUBTITLE/ATT. button
(When AMP mode is selected)
When the input signal is too high and the voice
distorts even by throttling the SR6001 VOLUME
control, turn on this function.
“ATT ” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the
output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is
selected.
‹2 AUDIO buttons
(When DVD mode is selected)
Used to select one of the audio language.
‹3 TREBLE +/- buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
‹4 SOURCE button
These buttons are used to switch the source of your
A/V Receiver / amplifer. Each time a source button is
pressed, the remote control changes to the source
which was pressed.
This remote control can control 12 types of equipment.
To change the A/V Receiver / amplifier source, press
this button twice within two seconds. The signal is
sent when it is pressed the second time.
Note:
Select the AMP as the source to use this remote
controll with the SR6001.
‹5 Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the
buttons while pointing the transmitter towards the
infrared receiver window of the SR6001 or other
AV equipment. Be sure to also point towards other
remote controls when using the learning function.
SR6001UDFU1ENG14.indd10SR6001UDFU1ENG14.indd10 06.12.214:13:58PM06.12.214:13:58PM
ENGLISH
11
OPERATION OF REMOTE CONTROL UNIT
REMOTE CONTROL
The distance between the transmitter of the remote
control and the IR SENSOR of the SR6001 should
be less than 5 meters. If the remote control is pointed
in a direction other than the IR SENSOR or if there is
an obstacle between them, use of the remote control
may not be possible.
Remote-controllable range
AVSURROUNDRECEIVERSR6001
PHONES
STANDBY
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
DISP MULTI AUTOTUNED STSPKR AB V-OFF
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP SURR DIRECT
AUTODISC6.1 MTX6.1
PCM
AAC
AUX1INPUT
AUDIO
S-VIDEO
DIGITALVIDEOLR
ENTER
DOWN
UP
VOLUME
POWERON/OFF
INPUTSELECTOR
SYSTEMREMOTECONTROLLER
RC5500SR
60°
SR6001
Approx. 5 m
Remote control unit (RC5001SR)
LOADING BATTERIES
The life of the batteries used with the remote control
is about 4 months with normal use. Also be sure to
replace batteries earlier when you notice that they
are getting weak.
1. Remove the back cover.
2. Insert the new batteries (AAA type) with correct
and polarity.
3. Close the cover until it clicks.
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
CAUTIONS ON BATTERIES
• Use “AAA” type batteries in this remote control
unit.
• We recommend that you use alkali batteries.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so in
the proper direction, following the + and - marks in
the remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use the
remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
SR6001UDFU1ENG14.indd11SR6001UDFU1ENG14.indd11 06.12.214:13:59PM06.12.214:13:59PM
ENGLISH
12
GENERAL INFORMATION OF RC5001SR TO SR6001
To control the SR6001 by your RC5001SR, you have to select the device AMP or TUNER by pressing the
SOURCE button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
CAT
P.SCAN
CAT
T.MODE
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
112233
445566
778899
00
+10+10
REMOTE CONTROLLER
RC5001SR
HT-EQHT-EQ
MULTI/MULTI/
SEND
MENUMENU
SPKR A/BSPKRA/B
ENTERENTER
EXITEXIT
INFOINFO
CH/
INPUTINPUT
T.TO NET.TON E
/SET UP/SET UP
M-SPKRM-SPKR
MUTEMUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
VOLUME
BASSBASS
TREBLETREBLE
dtsdts
P.DIRECTP.DIRECT
l/l/
OFF
ONON
SET
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
SURROUNDSURROUND
SLEEPSLEEP
DISPLAYDISPLAY
REC
AUDIOAUDIO
ANGLEANGLE
SUB TITLESUB TITLE
DISC+DISC+
CH-SELCH-SEL
V-OFFV-OFF
ATT.ATT.
AUX1
TAPE
A/DA/D
LEARN
LIP SYNC/LIP SYNC/
MEMOMEMO
CL
SOURCESOURCE
BAND
SOURCE ON / OFF
Turns the SR6001 on and off
POWER OFF Turns the SR6001 off
POWER ON Turns the SR6001 on
SLEEP Sets the sleep timer function
DISPLAY Changes the front display mode
P.DIRECT Selects the pure direct mode
SURROUND Selects the surround mode
AUTO (1) Selects auto surround
DOLBY (2) Selects DOLBY mode
dts (3) Selects dts mode
CSII (4) Selects CSII mode
EX/ES (5) Selects EX/ES
VIRTUAL (6) Selects VIRTUAL mode
M-CH ST (7) Selects Multi Channel Stereo
STEREO (8) Selects STEREO mode
NIGHT (9) Turns on or off NIGHT mode
7.1CH IN (0) Selects the 7.1CH IN
A/D (+10) Switches between the analog or digital inputs
LIP SYNC / INPUT Selects the LIP SYNC mode
HT-EQ Turns on or off HT-EQ mode
SPKR A / B Selects the speaker system
MULTI / CAT Turns on or off multi room
MUTE Decreases the sound temporarily
M-SPKR Turns on or off multi speaker
VOLUME 3/ 4Adjusts the over all sound level
INFO Displays the current setting on the monitor
MENU Enters the "SETUP MENU"
ENTER Enters the "SETUP MENU"
Confirms the setting in "SETUP MENU" mode
CURSOR Moves the cursor for setting in "SETUP MENU" mode
T.TONE / SET UP Enters the test tone menu
EXIT Exits from SETUP MENU
CH-SEL Calls up SETUP MENU and adjusts speaker levels or 7.1ch input level
V-OFF Turns on or off video output
ATT. Reduces the input level
BASS 3/ 4Adjusts the tone control of low frequency sound
TREBLE 3/ 4Adjusts the tone control of high frequency sound
SOURCE Selects a particular source component
TUNER MODE
TAPE
CAT
P.S C A NP.SC A N
CAT
T.MO DET.M OD E
--
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNINGTUNING
PRESETPRESET
--
++++
112233
445566
778899
00
+10+10
REMOTE CONTROLLER
RC5001SR
HT-EQHT-EQ
MULTI/MULTI/
SEND
MENUMENU
SPKR A/BSPKR A/B
ENTERENTER
EXITEXIT
INFOINFO
CH/
INPUTINPUT
T.TO NET.TON E
/SET UP/SET UP
M-SPKRM-SPKR
MUTEMUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
VOLUMEVOLUME
dtsdts
P.DIRECTP.DIRECT
l/l/
OFF
ON
SET
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
SURROUNDSURROUND
SLEEPSLEEP
DISPLAYDISPLAY
REC
AUX1
A/DA/D
LEARN
LIP SYNC/LIP SYNC/
MEMOMEMO
CLCL
SOURCESOURCE
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
BAND
0-9 Inputs the numeric
BAND Selects a radio band
T.MODE Selects the auto stereo mode or mono mode
P.SCAN Starts preset scan
CL Clears the inputting
MEMO Enters the tuner preset memory numbers
INFO Shows preset information
T.DISP Selects the display mode in RDS
F.DIRECT Selects the “Frequency direct input”
PRESET 3/ 4Selects a preset station up and down
TUNING 3/ 4Tunes a frequency station up and down
MULTI/CAT Turns XM Category Search mode ON/OFF
CH/CAT Switches categories in Category Search mode
SR6001UDFU1ENG14.indd12SR6001UDFU1ENG14.indd12 06.12.214:13:59PM06.12.214:13:59PM
ENGLISH
13
CONTROLLING MARANTZ COMPONENTS
1. Press the desired SOURCE button.
2. Press the desired operation buttons to play the selected component.
• For details, refer to the component’s user guide.
• It may not be possible to operate some models.
CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) CONTROLLING A MARANTZ VCR (VCR MODE)
SOURCE ON / OFF Turns the VCR on and off
0-9,+10 Inputs the numeric
LIP SYNC/INPUT Selects TV/VCR
CL Clears the inputting
MEMO Calls up programming menu
CH 3/ 4Selects VCR channel up or down
MENU Calls up the menu
ENTER Enters the setting
CURSOR Moves the cursor for setting in
"On Screen Display" mode
EXIT Exits the programming menu
REC Record
Pause Pause
Play Play
Stop Stop
Previous / Next Skips forward or previous track
Rewind / Forward Searchs forward or backward
AUDIO Selects the audio language
CONTROLLING A MARANTZ CD (CD MODE)
SOURCE ON / OFF Turns the CD player on and off
POWER OFF Turns the CD player off
POWER ON Turns the CD player on
0-9 Inputs the numeric
CL Clears the inputting
MEMO Programs
INFO Scrolls the disc information
MENU Switches the display information
Pause Pause
Play Play
Stop Stop
Previous/ Next Skips forward or previous track
Rewind/ Forward Searchs forward or backward
DISC+ CD changer next disc
SOURCE ON / OFF Turns the DVD player on and off
POWER OFF Turns the DVD player off
POWER ON Turns the DVD player on
0-9,+10 Inputs the numeric
CL Clears the inputting
MEMO Calls up programming menu
INFO Displays the disc information
MENU Calls up the menu of DVD disc
ENTER Enters the setting
CURSOR Moves the cursor for setting in
"On Screen Display" mode
T.TONE / SET UP Enters the test tone menu
EXIT Exits from SETUP MENU
T.Tone/Set up Calls up the setup menu of the
DVD player
Pause Pause
Play Play
Stop Stop
Previous/Next Ski p s f o r ward or previous
chapter/track
Rewind/ Forward Searchs forward or backward
DISC+ DVD changer next disc
ANGLE Selects the camera angle
SUBTITLE Selects the subtitle language
AUDIO Selects the audio language
TAP E
CAT
P.SCAN
CAT
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
+10+10
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TONET.TONE
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
CH/
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUME
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
REC
AUX1
LEARN
LIP SYNC/
HT-EQHT-EQ
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
OFFOFF
ONON
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
A/DA/D
MEMOMEMO
CLCL
SOURCESOURCE
AUDIOAUDIO
ANGLEANGLE
SUB TITLESUB TITLE
DISC+DISC+
CH-SELCH-SEL
V-OFFV-OFF
ATT.AT T.
BAND
TAP E
CAT
P.SCAN
CAT
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
+10+10
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TO NET. TON E
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
CH/
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUME
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
REC
AUX1
LEARN
LIP SYNC/
HT-EQHT-EQ
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
OFFOFF
ONON
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
A/DA/D
MEMOMEMO
BAND
CLCL
SOURCESOURCE
AUDIOAUDIO
ANGLEANGLE
SUB TITLESUB TITLE
DISC+DISC+
CH-SELCH-SEL
V-OFFV-OFF
ATT.AT T.
TAP E
CAT
P.S C A N
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
CATCAT
+10
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TONET.TONE
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUM E
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
RECREC
AUX1
LEARN
LIP SYNC/
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
CLCL
SOURCESOURCE
AUDIOAUDIO
OFF
ON
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
CH/CH/
A/D
HT-EQ
MEMO
BAND
SR6001UDFU1ENG14.indd13SR6001UDFU1ENG14.indd13 06.12.214:14:00PM06.12.214:14:00PM
ENGLISH
14
CONTROLLING A MARANTZ CD RECORDER (CDR MODE)
SOURCE ON / OFF Turns the CD recorder on and off
POWER OFF Turns the CD recorder off
POWER ON Turns the CD recorder on
0-9 Inputs the numeric
CL Clears the inputting
MEMO Programs
INFO Scrolls the disc information
MENU Switches the display information
REC Record
Pause Pause
Play Play
Stop Stop
Previous / Next Skips forward or previous track
Rewind / Forward Searchs forward or backward
CONTROLLING A MARANTZ MD DECK (MD MODE)
SOURCE ON / OFF Turns the MD deck on and off
POWER OFF Turns the MD deck off
POWER ON Turns the MD deck on
0-9 Inputs the numeric
CL Clears the inputting
MEMO Programs
MENU Switches the display information
REC Record
Pause Pause
Play Play
Stop Stop
Previous / Next Skips forward or previous track
Rewind / Forward Searchs forward or backward
CONTROLLING A MARANTZ TAPE DECK (TAPE MODE)
SOURCE ON / OFF Turns the TAPE deck on and off
POWER OFF Turns the TAPE deck off
POWER ON Turns the TAPE deck on
0-9 Inputs the numeric
CL Clears the inputting
MEMO Programs
REC Record
Pause Pause
Play Play
Stop Stop
Previous / Next Skips forward or previous track
Rewind / Forward Searchs forward or backward
TAP E
CAT
P.SCAN
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
+10
CAT
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TO NET. TON E
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUME
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
RECREC
AUX1
LEARN
LIP SYNC/
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
CLCL
SOURCESOURCE
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
OFFOFF
ONON
A/D
HT-EQ
MEMO
CH/
AUDIO
BAND
TAP E
CAT
P.SCAN
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
+10
CAT
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TO NET. TON E
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUME
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
RECREC
AUX1
LEARN
LIP SYNC/
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
CLCL
SOURCESOURCE
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
OFFOFF
ONON
A/D
HT-EQ
MEMO
CH/
AUDIO
CAT
P.SCAN
T.MODE
-
T.DISPT.DISP
F.DIRECTF.DIRECT
PTYPTY
TUNING
PRESET
-
++
TAP E
REMOTE CONTROLLER
RC5001SR
112233
445566
778899
00
+10
CAT
MENUMENU
ENTERENTER
EXITEXIT
INFOINFO
T.TO NET. TON E
/SET UP/SET UP
MULTI/
SEND
SPKR A/B
INPUT
M-SPKR
MUTE
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
VOLUM E
BASS
TREBLE
P.DIRECT
SET
SURROUND
SLEEP
DISPLAY
RECREC
AUX1
LEARN
LIP SYNC/
EX/ESEX/ES
VIRTUALVIRTUAL
CSCS
dtsdts
l/l/
7.1CH IN7.1CH IN
STEREOSTEREO
NIGHTNIGHT
M-CH STM-CH ST
AUTOAUTO
CLCL
SOURCESOURCE
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
OFFOFF
ONON
A/D
HT-EQ
MEMO
CH/
AUDIO
SR6001UDFU1ENG14.indd14SR6001UDFU1ENG14.indd14 06.12.214:14:00PM06.12.214:14:00PM
ENGLISH
15
RESETTING THE CODE
123
SEND
INPUT
dts
P.DIRECT
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LEARN
LIP SYNC/
l/
SOURCE
1.
CAT
P.S C A N
CAT
T.MODE
123
456
789
0
+10
HT-EQ
MULTI/
SEND
MENU
SPKR A/B
INFO
CH/
INPUT
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUM E
dts
P.DIRECT
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LEARN
LIP SYNC/
MEMO
CL
l/
SOURCE
2.
REMOTE CONTROLLER
RC5001SR
TAPE
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVDDVD VCRVCR
DSSDSS
TVTV
1.
1. Press and hold down the SOURCE button
for appliance which should be controlled and
press SET button until the SEND indicator
blinking twice.
Then back light flushes.
2. Press the below codes to reset.
TV : 1000
DVD : 2000
VCR : 3000
DSS : 4000
The indicator will blink twice.
Note:
After this procedure, the selected SOURCE button is
set initial code.
2. Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking
twice.Then back light flushes.
3. Aim the remote control at the appliance and
slowly alternate between pressing CH+ button
and the
SOURCE ON/OFF
button for the
appliance.
4. Stop when the appliance turns off.
5. Press ENTER button once to lock in the code.
CHECKING THE CODE
123
SEND
INPUT
dts
P.DIRECT
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LEARN
LIP SYNC/
l/
SOURCE
1.
CAT
P.S C A N
CAT
T.MO DE
123
456
789
0
+10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
INPUT
T.TO NE
/SET UP
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
P.DIRECT
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
l/
SOURCE
2.
4.
3.
REMOTE CONTROLLER
RC5001SR
TAPE
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OF F
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVDDVD VCRVCR
DSSDSS
TVTV
1.
1. Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light flushes.
2. Press the INFO button.
The SEND indicator will blink twice.
3. To view the code for first digit, press 1once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note:
If a code digit is “0”, the SEND indicator will not
blink.
4. Repeat step
3three more times for remaining
digits. Use 2for the second digit, 3for the third
digit, and 4for the fourth digit.
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
TAPE
-
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
AMP
AUX2
TUNER
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
DVDDVD VCRVCR
DSSDSS
TVTV
1.
P.SCAN
CAT
T.MODE
+10
112233
445566
778899
00
HT-EQ
SPKR A/B
CH/
INPUT
MUTE
EX/ES
VIRTUAL
CS
VOLUM E
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
SOURCE
2.
1.
1. Press and hold down the SOURCE button for the
appliance which should be controlled and press
SET button until the SEND indicator blinks twice.
Then back light flushes.
2. Press the 4-digit code for appliance (code table
at the end of this book)
When the procedure is successful, the
SEND
indicator will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SCANNING THE CODE TABLE
T.MODE
123
456
SEND
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LEARN
LIP SYNC/
l/l/
SOURCESOURCE
2.
REMOTE CONTROLLER
RC5001SR
TAPE
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVDDVD VCRVCR
DSSDSS
TVTV
2.
CAT
P.SCAN
CAT
T.MO DE
123
456
789
0
+10
HT-EQ
MULTI/
MENU
SPKR A/B
EXIT
INFO
CH/
INPUT
T.TO NE
/SET UP
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUM E
dts
P.DIRECT
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
l/
SOURCE
ENTER
3.
3.
5.
1. Switch on the appliance which should be
controlled.
BASIC OPERATION
NORMAL MODE
(
When operating Marantz AV equipment products
)
This remote control is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, MD, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifier).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1. Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifier on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifier source
changes to DVD.
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2
seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote control is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
control.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote control
source name
Corresponding preset
code
Device name
TV TV Television
DVD DVD DVD player
VCR VCR Video deck
DSS SATELLITE Satellite broadcasting
tuner equipment
SR6001UDFU1ENG14.indd15SR6001UDFU1ENG14.indd15 06.12.214:14:00PM06.12.214:14:00PM
ENGLISH
16
LEARN MODE
This remote control is capable of learning and storing
codes used by other remote controls that you already
own.
For codes which are not learned, the remote control
will transmit either the Marantz preset codes from
the initial settings, or remote codes from another
manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control signals is
located at the top of the remote control.
Notes:
• This remote control is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
1. Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 0.05 m (2 inches).
SYSTEMREMOTECONTROLLER
RC5500SR
0.05 m
2. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
SET
CAT
MULTI/
ENTER
INFO
M-SPKR
MENU
3. Select the SOURCE button to select the
SOURCE.
REMOTE CONTROLLER
RC5001SR
TAP ETA PE
BASS
TREBLE
MDMD
CDRCDR
CDCD
DVDDV D
AMPAMP
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
4. Select the button to be learned.
• LEARN indicator lights up.
123
456
T.MODE
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
5. Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
• When the SEND indicator blinks once,
repeat this step.
• When the memory of the RC5001SR is
full, the LEARN and SEND indicators blink
once. If you want to learn the code, you
should erase other learned button.
6. Repeat steps
4and 5to learn other buttons in
same SOURCE.
7. Repeat steps
3to 6to learn other SOURCE.
8. When you have finished programming the
remote controller, press the SET button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
SEND
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
SOURCE
INPUT
LIP SYNC/
LEARN
Notes:
• When the SEND indicator blinks once again, the
transmitting code is unavailable for RC5001SR, or
the transmitting signal is intercepted by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
ERASING PROGRAMMED CODES
(RETURNING TO INITIAL SETTINGS)
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
Erasing the code by buttons
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
MENU
ENTER
INFO
M-SPKR
2. Select the SOURCE button to select the button
to be erased.
REMOTE CONTROLLER
RC5001SR
TAP ETA PE
BASS
TREBLE
MDMD
CDRCDR
CDCD
DVDDV D
AMPAMP
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
3. Press and hold down the SLEEP button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
4. To return the NORMAL mode, press the SET
button.
Erasing the code by SOURCE
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
ENTER
INFO
M-SPKR
MENU
2. Press and hold down the SLEEP button and
press the learned SOURCE button twice to be
erased.
• LEARN indicator lights.
TAPETAPE
AMP
BASS
TREBLE
CH
-
SEL
V
-
OFF
ATT
.
MDMD
CDRCDR
CDCD
DVDDV D
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TO NE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Erasing the all SOURCES
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
MENU
ENTER
INFO
M-SPKR
2. Press and hold down the SLEEP button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TO NE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
SR6001UDFU1ENG14.indd16SR6001UDFU1ENG14.indd16 06.12.214:14:01PM06.12.214:14:01PM
ENGLISH
17
CONNECTIONS
SPEAKER PLACEMENT
The ideal surround speaker system for this unit is 7-
speaker systems, using front left and right speakers,
a center speaker, surround left and right speakers,
a surround back left and right speakers, and a
subwoofer.
For best results we recommend that all front speakers
be of the same type, with identical or similar driver
units. This will deliver smooth pans across the front
sound stage as the action moves from side to side.
Your center channel speaker is very important as
over 80 % of the dialog from a typical motion picture
emanates from the center channel.
It should possess similar sonic characteristics to the
main speakers. Surround channel speakers need not
be identical to the front channel speakers, but they
should be of high quality.
The surround center speaker is useful for playback
of Dolby Digital Surround EX or DTS-ES. One of
the benefits of both Dolby Digital and DTS is that
surround channels are discrete full range, while they
were frequency limited in earlier “Pro Logic” type
systems.
Bass effects are an important part of home theater.
For optimal enjoyment a subwoofer should be used
as it is optimized for low frequency reproduction. If
you have full range front speakers, however, they
may be used in place of a subwoofer with proper
setting of the switches in the menu system.
90°
110°
22°
30°
135°
150°
0°
Front left and right speakers
We recommend to set the front L and R speakers
with 45-60 degrees from the listening position.
Center speaker
Align the front line of the center speaker with the front
L/R speakers. Or place the center speaker a little
backward from the line.
Surround left and right speakers
When the SR6001 is used in surround operation,
the preferred location for surround speakers is on
the side walls of the room, at or slightly behind the
listening position.
The center of the speaker should face into the
room.
Surround back left and right speakers
Surround back speakers are required when a full 7.1-
channel system is installed.
Speakers should be placed on a rear wall, behind the
listening position.
The center of the speaker should face into the
room.
Subwoofer
We recommend using a sub-woofer to have maximum
bass effect. Sub-woofer bears only low frequency range
so you can place it any where in the room.
HEIGHT OF THE SPEAKER UNITS
Front left and right speakers, and a center speaker
Align the tweeters and mid-range drivers on the
three front speakers at the same height, as best as
possible.
Surround left and right speakers, and surround
back speaker
Place the surround left, right and surround back
speakers higher than your ears by about 70cm–1m.
Also place the speakers at the same height, as best
as possible.
70cm
1m
Note:
• Use magnetically-shielded speakers for front left,
right and the center speakers when the speakers are
installed near the TV and the TV is a monitor type.
CONNECTING SPEAKERS
FM (75)GND AM
DC OUT
OUTPUT
COMPONENT
VIDEO
IN OUT
PRE
OUT
SLL
RSR
FLASHER
IN
SPEAKER
SYSTEMS
INPUT1(DVD)
COAX.
DIGITALIN
DIGITALOUT
3
54
21
SURROUND
BACK
OUT
R
OUT
L
RS-232C
OUTPUT
TAPE CD/CD-R
OUTOUTIN
MULTI
R
L
DSS
(AUX2)
AUDIO
TV
7.1CH
IN
IN
OPT.
DVD(2)DSS(4)
TV(1)
VIDEO
OUT
VCR(3)
OUTIN
RC-5 MULTI RC
INPUT1(TV)
INPUT4(DSS)
IN
SR
VCR
IN
INPUT3(VCR)
DVD SL
INPUT2(DSS)
ANTENNA
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
YYY
DVD(2)
DSS(4)
VCR(3)
TV(1)MONI.OUT
MONITOR
OUT
SBR
SBL
SBR
SBL
C
SW
SW
C
R
L
R
R
R
L
LL
AC IN
INPUT2(DVD)
S-VIDEO
MODELNO. SR6001
FRONT
B
SURR
OUND
CEN
TER
FRONT
A
ON
OFF
MULTISPEAKER
/
SPEAKER C
FRONTA OR B.CENTER.SURR.
SURR BACK : 6 - 8 OHMS
FRONT A+ B :8 OHMS
HDMI
Ver1.2
UNSWITCHED
1.25A150W
SWITCHED
1.25A150W
AC OUTLETS
120V 60Hz
XM
INVERT
OUTPUT
INPUT
LEVEL
BTL REMOTECONT.EXT.CONT.IN
VIDEO/
+5~13VDC
SYSTEMOUT OUT
INPUT
MASTERSLAVE
MIN MAX
IN
F
U
S
E
SPEAKERSYSTEM
MINIMUM4 OHMS
Powered
subwoofer
Power
Amplifier
Passive
subwoofer
Surround
Right Left
FRONT A
Surround
BACK
Center
Right Left
CONNECTING SPEAKER WIRE
1. Strip away approx. 3/8 inch (10 mm) of wire
insulation.
2. Twist the bared wire ends tight, to prevent short
circuits.
3.
Loosen the knob by turning it counterclockwise.
4. Insert the bare part of the wire into the hole in
side of each terminal.
5. Tighten the knob by turning it clockwise to
secure the wire.
1. 2.
3. 4. 5.
3/8 inch
(10 mm)
Front Right
Front Left
Front Center
Surround Left Subwoofer
Surround Back
Left
Surround Right
Surround Back
Right
Right Left
FRONT B
Right Left
SR6001UDFU1ENG14.indd17SR6001UDFU1ENG14.indd17 06.12.214:14:02PM06.12.214:14:02PM
Other manuals for SR-6001
2
Table of contents
Other Marantz Receiver manuals
Marantz
Marantz SR4002 User manual
Marantz
Marantz SR5004 User manual
Marantz
Marantz 19 User manual
Marantz
Marantz SR5400 User manual
Marantz
Marantz SR5002 User manual
Marantz
Marantz NR1602 User manual
Marantz
Marantz SR-14EX Manual
Marantz
Marantz NR1605 User manual
Marantz
Marantz SR5003 User manual
Marantz
Marantz SR4200 User manual
Marantz
Marantz SR4300 User manual
Marantz
Marantz SR9300 User manual
Marantz
Marantz SR8300 User manual
Marantz
Marantz M-CR510 User manual
Marantz
Marantz SR5007 User manual
Marantz
Marantz AV7005 User manual
Marantz
Marantz 1530 User manual
Marantz
Marantz SR7008 User manual
Marantz
Marantz SR5008 User manual
Marantz
Marantz SR-7001 Reference manual
