Martin Yale Industries CHECKSIGNER 930A Datasheet

CHECKSIGNER 930A
OPERATING INSTRUCTIONS
&
PARTS LIST
FEATURES
•TRACTOR FEED DRIVE FOR ACCURACY •TRI-COLOR INK ROLL (Optional)
•L.C.D. COUNTER WITH MEMORY •KEY-LOCK SECURITY
•DUAL SIZE SELECTOR SWITCH •IMPACT-PROOF LEXAN HOOD
•POWER-ON INDICATOR LAMP •SILENT BELT MOTOR DRIVE
•FULLY ADJUSTABLE IMPRESSION LOCATION •FAN-COOLED MOTOR
•FULLY FUSED ELECTRICAL COMPONENTS
SPECIFICATIONS
DIMENSIONS: Height 12 9/16”
Width 23”
Depth 7 5/8”
WEIGHT: 30 lbs.
ELECTRICAL RATING: 115 Volts, 60 Hz., 2.0 Amps.
FORM SIZE: Length Width
3 1/2” or 7” 16” Max - 3 1/2” Min.
SPEED: 14,280 3 1/2” Forms per Hour
Part No. Description Qty
W-O008572 Base 1
W-O008607 L.S. Extrusion 1
M-S045039 L.C.D. Counter 1
W-O008649 LS Bottom Trim 1
W-O008573 End Cover 2
W-O008616 Top/Signature Shaft 1
W-O008730 Interlock Sw. Block 1
M-O008729 LH Ink Roller Sup Block 1
M-S013001 Tractor Shaft Bushing 2
M-O008623 Cover Stop 2
M-S001077 6-32X1/4 Phil Flat Head 2
M-S033038 Hood Interlock Switch 1
M-S019021 3/4" Set Collar 2
W-O008601 Left Side Main Frame 1
W-O008735 B/O LS Hood Bracket 1
M-S013039 Print Shaft Bushing 4
M-S005001 Ink Roller Thumb Screw 1
WRA008530 Black Ink Roller Asm. 1
WRA008575 3 Color Ink Roller Asm. 1
W-O008652 Ink Roller Shaft 1
M-O008728 RH Ink Roller Sup Block 1
W-A008610 Hood Assembly 1
M-O008613 1/2 Tie Rod 1
W-O008734 B/O RS Hood Bracket 1
M-S015150 Arrow Label 1
M-S015169 2 Arrow Sticker 1
W-O008590 RS Extrusion 1
M-S033064 On/Off/Momentary Switch 1
W-O008602 RS Main Frame 1
M-S033069 Spdt Rocker Switch 1
W-A008576 3 Pos Key Sw 1
M-S037020 115V USA Line Cord 1
M-S004029 8X1 Phil Mach Screw 8
W-A008656 RS Tractor Feed, Assy 1
W-O008614 B.O. 5/16 Tie Bar 1
W-O008615 Bottom/Platen Shaft 1
W-A008726 3.5-7 Sig.Plt.Holdr,Asm 1
M-O008516 Back-Up Roller 1
*See Note*
M-O008621 5/16 Square Drive Shaft 1
M-S037054 LH Tractor Feed 1
M-O008571 RS Bottom Extrusion 1
M-S021024 115vac Motor 1
M-S045027 2 Amp Fuse,3ag 1
M-S030021 Rubber Foot 4
M-S035015 Strain Relief #Sr-5p-4 1
W-O008606 Bottom Cover 1
M-S025008 144xl037 Timing Belt 1
M-S045040 Battery For Counter 2
M-O008543 Nylon Gear 1
M-S013040 Oilite Bushing 3/4X1X3/4 1
M-S022024 Pulley 32x312 Bore 1
M-S022025 28t Pulley,1/4"ID 1
M-S022026 10xl037 G Pulley 1
M-S033040 Microswitch 2
M-S035006 Snap Bushing 2
M-S035022 Panel Bushing,UB-625 1
M-S045016 Fuse Block 1
W-O008654 Nylon Gear 1
40 38
1
32
35
37 33
36
2
11
7
6
5
13
3
22
4
20
25
26
10
27
29
30
31
18 19
24
17
12
34
39
8
21
16
9
14
PARTS LIST & DIAGRAM
28
36 W-A008726 3.5-7 Sig.Plt.Holdr,Asm
A M-S010013 5100-100 Ext Snap Rg 1
B M-O008538 Sig Plt Spring 1
C M-O008670 Signtr Plate Holder 1
D M-S023016 #224 O-Ring Epdm 1
E M-S018001 1/8d X 1/2 Rollpin 2
F M-S002055 10-32x3/16 Brass Tip 2
G M-O008611 Retainer-Sign.Plate 1
H W-A008617 Turn,Spring Retainer 1
36B
36H
36A
36C
36D
36E
36F
36G
15
23
251 Wedcor Avenue lWabash, Indiana 46992
Phone [phone] lFax [phone]
Email: [email protected] lWebsite: www.martinyale.com
Rev. 5 07/17/2014
M-S027200
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Not Shown
* Signature plates ordered seperately, see enclosed order form.
ProSource Packaging, Inc.
14911 Stuebner Airline Suite A
Houston, TX 77069
800-203-0233
www.Machine-Solution.com

INTRODUCTION
Thank you for purchasing a Martin Yale Model 930A Check Signer. This signer has been designed and developed for easy
operation and maintenance. However, we recommend that you familiarize yourself with the machine and carefully read
these instructions.
OPERATOR SWITCH WITH INDICATOR LIGHT: (fig. 1)
The purpose of this switch is to jog the machine and put it in the off and
on position. The red indicator light with the switch shows that the
machine is in the “ON” position. When the switch is in the “on” position,
the machine will automatically operate and sign forms.
FORM SIZE SWITCH:
This switch has 2 positions for form sizes: 3 1/2” and 7”. To operate the
machine, the form size switch must be in one of the two form size posi-
tions.
SELECTOR SWITCH:
The selector switch provides the functions of resetting the counter and
turning the machine off. To operate the machine, the selector switch
must be in the sign position.
ARROW ON MAINFRAME AND 2 ARROW COLLAR:
These are situated on the right side mainframe of the machine and on the 3/4” set collar (fig 1). The purpose of these
arrows is for aligning the forms on the machine.
TRACTOR ADJUSTMENT PROCEDURE
NOTE: DISCONNECT POWER SUPPLY.
1. Open the hinged covers on the right & left tractor feeds.
2. Release the lock lever on the left tractor feed by pulling the tractor feed
release lever forward.
3. Place the appropriate width form over the right tractor feed index pins. Close
the cover.
4. To adjust for form width, slide the left tractor feed to align with the form holes
on the opposite side of the form. Align the tractor feed index pins and close
the hinged cover.
5. Slide the tractor feed as far left as possible. Avoid excessive side tension on
the form. Push the tractor feed release lever toward the rear of the machine.
6. Open the hinged covers and remove the form.
SIGNATURE PLATE INSTALLATION
(CONNECT THE POWER SUPPLY CORD TO 110-115V.
OUTLET.)
1. Insert the key into the selector switch and rotate to sign position.
2. Jog the machine using the operator switch until one of the index pins
on the signature plate retainer is on top.
3. Raise the hood by lifting upwards in center.
4. Slide the retainer collar to the left. Install the signature plate over the
rollpin. Release the retainer collar.
NOTE: Signature plate(s) must be indexed on the rollpin prior to
machine operation.
5. Close the hood and jog the machine to the next rollpin.
Form size:
3 1/2” - 2 signature plates required
7” - 1 signature plate required
IMPRESSION LOCATION ADJUSTMENT
To adjust the location of the signature, a 2 arrow collar and start arrow (fig. 1) have been installed on the machine. Jog
the machine to line up the proper collar arrow with the mainframe arrow. Select the proper size form on the form size
switch. Place the form over the tractor feed index pins exposing 3 holes past the end of the tractor feed (fig. 2).
NOTE 1:
Jogging to remove the last form will be necessary when in the run position on the last check.
NOTE 2:
Before the next step, always jog the machine to align the form on the 2 arrow collar with the mainframe arrow.
IMPORTANT:
DO NOT LOAD THE FORM INTO THE MACHINE WHILE THE RED LIGHT IS ON. THE
MACHINE WILL RUN IF THE OPERATOR SWITCH IS ON AND THE TRACTOR FEED SWITCH
IS ACTIVATED.
If the signature is off, loosen the 2 set screws on the signature plate retainer (fig. 3) and 1 set screw on the back-up
roller. Rotate the signature plate retainer or if necessary move the signature plate retainer side to side (keep the back-
up roller in alignment with the signature plate retainer at all times). Lock the set screws and test run forms thru the
machine.
INK ROLLER ADJUSTMENT
Before operating the machine, the ink roller must be aligned to contact the signature plates. There are two adjustments
on the ink roller. A thumb screw is provided next to the roller itself to move it across the shaft. In addition there are four
(4) adjustment screws in the hood which adjusts it up or down to contact the signature plate (fig. 4).
NOTE: Avoid excessive pressure on the signature plate.
MAINTENANCE
OIL PERIODICALLY WITH LIGHT MACHINE OIL:
1. Signature plate shaft bushings.
2. Back up roller bushings.
3. Tractor drive shaft bushings.
4. Belt adjuster eccentric bushing. (Requires removal of left side cover).
CHECK DRIVE BELT TENSION ANNUALLY. (Requires removal of left side cover).
CLEAN TRACTOR DRIVE MICRO SWITCH OF PAPER DUST. (As required).
REPLACE BATTERIES IN COUNTER EVERY 3-5 YRS. (Requires removal of bottom cover plate).
On/Off/Momentary
Switch
2 Arrow
Collar
Arrow on RS
Main Frame
Tractor Feed Assembly
3 Position
Key Switch
SPDT Rocker
Switch
Tractor feed release lever
Tractor feed
index pin
Fourth hole
Feed
Hinged
cover
Figure 2
Figure 1
Retainer collar
Set screw
Signature Plate Holder
Rollpin
Signature
plate retainer
Set screws
Back-up
roller
Figure 3
Ink Roller
Ink Roller Thumb Screw
Support block
mounting screws
Figure 4