Masport R5000 WOOD FIRE User manual

MODEL:
R5000 WOOD FIRE
INSTRUCTION FOR FAN INSTALLATION
58327115.11.2013

CAUTION:
YOU NEED A POWER POINT ON THE WALL, SO THAT YOU CAN PLUG IN THE
FAN. NO POWER POINT SHALL BE LOCATED IMMEDIATELY ABOVE THE
HEATER. IF ANY ELECTRICAL WORK IS REQUIRED, IT MUST BE CARRIED
OUT BY A LICENSED ELECTRICIAN. IN SOME REGIONS POWER POINTS ARE
NOT PERMISSIBLE WITHIN THE FLOOR PROTECTOR AREA, PLEASE CHECK
WITH YOUR LOCAL AUTHORITY.
FAN BOX INSTALLATION:
PEDESTAL VERSION (Figure 1)
Figure 1. Pedestal version installation
1. Break out the ‘knock out’ part on the left face of the pedestal (looking from the
front) to allow the switch to be inserted.
2. Remove the sharp tabs left in the hole with a file.
3. Stick the fan operation label next to this hole.
4. Fit the 1/4 brass spade terminal using fasteners in the same sequence at the
bottom of the pedestal, as shown in Figure 2. Ensure that is done tight (This
may have been already done in the factory).
5. Stick the earth decal next to the earth tab. (This may have been already done
in the factory).
6. Remove switch from wiring loom.
7. Feed the wiring loom up the cavity next to the ash box.
8. Feed the end through the knockout fan switch hole, shown in Detail A.
9. Refit the switch to the wiring loom.
10. Ensure wires to be connected in Figure 3, and then press the switch into the
rectangular knocked off rectangular hole, ‘II’ should be above ‘0’. It should
snap firmly into place.

Figure 2. Earth connection installation Figure 3. Fan switch
11. Connect the loose earth wire (green) to the brass tab at rear of the left side of
pedestal, this is a push-on connection.
12. Lift the fan assembly and secure to the back of the pedestal with 4 black
screws supplied. For ease of fitment, put the top screws first, then the bottom
ones as shown in Figure 1.
13. Plug the 3-pin plug into the wall outlet and test the operation of the fan.
LEG VERSION (Figure 4)
1. Break out the ‘knock out’ part on the left side of the leg (looking from the front)
to allow the switch to be inserted.
2. Remove the sharp tabs left in the hole with a file.
3. Stick the fan operation decal next to this hole. Remove the rear brace from the
back of the heater, as shown in Figure 4 and discard this part.
4. Fit the supplier 1/4 brass spade terminal using fasteners in the same sequence
at the back of the heater, as shown in Figure 2. Ensure that is done tight (This
may have already done in the factory).
Figure 4. Leg version installation

5. Remove switch from wiring loom.
6. Remove bottom heatshield by unfastening 6 black screws ref. Fig 4.
7. Lift and support the fan whilst feeding the wiring loom through square hole in
rear channel of the leg.
8. Continue to feed the end through the knockout fan switch hole, shown in Fig 4
Detail B.
9. Fasten fan assembly into position and fit to the back of the leg with 4 black
screws supplied. For ease of fitment, put the top screws first, then the bottom
ones as shown in Figure 4.
10. Refit the switch to the wiring loom.
11. Ensure wires to be connected in Figure 3, and then press the switch into the
knockout rectangular hole, ‘II’ should be above ‘0’. It should snap firmly into
place.
12. Connect the loose earth wire (green) to the brass tab at rear channel of the
leg, this is a push-on connection.
13. Refit the bottom heatshield by fastening 6 black screws ref. Fig 4.
14. Plug the 3-pin plug into the wall outlet and test the operation of the fan.
Circuit Diagram (Figure 5)
Figure 5. Circuit Diagram—Revision A
The circuit diagram is shown as follows in Figure 5.

Figure 5. Circuit Diagram—Revision B— 15.11.2013

AIRSLIDE REPLACEMENT (NZ MODEL ONLY):
Figure 6. Step one
Step One (Figure 6):
1. Remove the door from the heater.
2. Remove 2 x (M6X10) screws which
fasten the louver in position.
3. Remove the louver from the heater.
Figure 7. Step two
Step Two (Figure 7):
1. Remove 2 x M6 nuts from the back of
the air deflector, remove bolts and
spacers from front, hold air deflector in
place as you do this.
2. Remove the Airslide from the heater
and discard this part marked 983221.
Figure 8. Step three Step Three (Figure 8):
1. Discard Airslide part 983221 air and
replace it with Airslide part 983278.
In New Zealand, a special Airslide marked 983278 must be fitted if the fan is
installed. Procedure for replacing Air Slide is shown as follows:
983221

Figure 9. Step four
Step Four (Figure 9):
1. While holding the deflector in correct
position ref detail D of Fig 9, refit the
new Airslide (983278) to the front of
the heater.
2. Refit 2 spacers and 2 x (M6X50) bolts
back to the top front of the heater.
3. Tighten the 2 x M6 nuts to the back of
the air deflector to secure all the parts
together.
Figure 10. Step five
Step Five (Figure 10):
1. Refit the louver to the top of the
heater using the 2 x (M6X10) screws.

SAFETY:
THE APPLIANCE IS NOT INTENED FOR USE BY YOUNG CHILDREN OR
INFIRM PERSONS WITHOUT SUPERVISION.
SUPERVISE YOUNG CHILDREN TO ENSURE THEY DO NOT PLAY WITH THE
APPLIANCE.
IF A SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE
MANUFACTURER, ITS SERVICE AGENT OR A SUITABLY QUALIFIED
PERSON, IN ORDER TO AVOID ELECTRICAL HAZARD.
MAINTENANCE:
THE FAN SHOULD NEED LITTLE ATTENTION OTHER THAN OCCASIONALLY
(PERHAPS ONCE A YEAR) REMOVING IT TO CLEAN DUST AND LINT FROM
THE IMPELLER. FIRST UNPLUG THE MAINS LEAD FROM THE POWER POINT.
REMOVE THE FAN BY UNDOING THE 4 SCREWS HOLDING IT INPOSITION.
CLEAN THE IMPELLER BLADES CAREFULLY BY BLOWING OR VACUUMING.
DO NOT APPLY FORCE TO THE IMPELLERS. REINISTALL THE FAN.
OPERATING HINTS FOR CLEAN BURNING AND BEST EFFICIENCY:
SWITCH OFF THE CIRCULATING FAN WHEN THE FIRE IS BURNING AT LOW
HEAT OUTPUTS. USE ONLY THE SLOW FAN SPEED AT MEDIUM HEAT
OUTPUT, MOVING TO THE HIGHER SPPED ONLY WHEN FULL HEAT OUTPUT
HAS BEEN REACHED.
PLEASE REFER ALSO TO THE OWNERS MANUAL FOR THE FIRE FOR MORE
INFORMATION.