MasterCraft 055-6705-8 User manual

CHOP SAW
INSTRUCTION
MANUAL
IMPORTANT:
Please read this manual carefully before
using this chop saw and save it for reference.
model no. 055-6705-8
model no. 055-6705-8

3
IMPORTANT:
Read and understand this instruction manual thoroughly before using the product. The manual
contains important information for your safety as well as operating and maintenance advice.
Keep this instruction manual for future use. Should this product be passed on to a third party, then
this instruction manual must be included.
250100
NOTE:
If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline
at 1-800-689-9928.
TABLE OF CONTENTS
Specications 4
Safety guidelines 5–13
Key parts diagram 14
Operating instructions 15–24
Maintenance 25–26
Exploded view 27
Parts list 28–29
Warranty 30–31
TABLE OF CONTENTS
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

4
SPECIFICATIONS
Motor 120V AC, 60 Hz
Amperage 15A
Speed 3500 RPM
(no load)
Disc size 14" (35.5 cm)
Arbor 1" (2.5 cm)
Cutting capacity 4 3/4" (12 cm) round
4 3/8" (11 cm) square
6 7/8" (17.5 cm) rectangular
Pivoting fence (0–45º, right & left)
Weight 37 lb 8 oz
(17 kg)
GENERAL SAFETY WARNINGS
WARNING: Before using this tool or any of its accessories, read this manual
and follow all safety rules and operating instructions. The important precautions,
safeguards and instructions appearing in this manual are not meant to cover all
possible situations. It must be understood that common sense and caution are factors
that cannot be built into the product.
This instruction manual includes the following:
• General safety rules • Operation
• Specic safety rules and symbols • Maintenance
• Functional description • Accessories
• Assembly
EYE, EAR & LUNG PROTECTION
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA
Z94.3 OR ANSI SAFETY STANDARD Z87.1.
FLYING DEBRIS can cause permanent eye damage.
Prescription eyeglasses ARE NOT a replacement for proper eye
protection.
WARNING: Non-compliant eyewear can cause serious injury if broken while
operating a power tool.
WARNING: Use hearing protection, particularly during extended periods of
operation of the tool, or if the operation is noisy.
WARNING: Wear a dust mask that is designed to be used when operating a
power tool in a dusty environment.
SAVE THESE INSTRUCTIONS FOR REFERENCE
!
!
!
5
SPECIFICATIONS
SAFETY GUIDELINES
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

WARNING: Dust that is created by power sanding, sawing, grinding, drilling, and
other construction activities may contain chemicals that are known to cause cancer, birth
defects, or other genetic abnormalities. These chemicals include:
• Lead from lead-based paints
• Crystalline silica from bricks, cement, and other masonry products
• Arsenic and chromium from chemically treated lumber
The level of risk from exposure to these chemicals varies, according to how often this type of
work is performed. In order to reduce exposure to these chemicals, work in a well-ventilated
area, and use approved safety equipment, such as a dust mask that is specically designed to
lter out microscopic particles.
ELECTRICAL SAFETY
WARNING: 
proper circuit protection.
This tool is wired at the factory for 120V AC operation. It must be connected to a 120V AC,
15 A circuit that is protected by a time-delayed fuse or circuit breaker. To avoid shock or re,
replace power cord immediately if it is worn, cut or damaged in any way.
POWER TOOL SAFETY
WARNING: Read all safety warnings and all instructions. Failure to follow the
.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
-
mable liquids, gases or dust. Power tools create sparks, that may ignite the dust or fumes.
SAVE THESE INSTRUCTIONS FOR REFERENCE
!
!
Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching
outlets will reduce risk of electric shock.
Avoid bodily contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Using a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a supply protected by
ground fault circuit interrupter (GFCI). Use of a GFCI reduces the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a power

or medication. A moment of inattention while operating power tools may result in serious
personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate
conditions will reduce personal injuries.
SAVE THESE INSTRUCTIONS FOR REFERENCE
6 7
SAFETY GUIDELINES
SAFETY GUIDELINES
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

Prevent unintentional starting. Ensure the switch is in the Off-position before

Carrying power tools with your nger on the switch or energizing power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection of dust-extraction and dust-collection
facilities, ensure these are connected and properly used. Dust collection can reduce dust-
related hazards.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for your job. The correct power
tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it On and Off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.

before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
SAVE THESE INSTRUCTIONS FOR REFERENCE
8
Store idle power tools out of the reach of children and do not allow people unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other conditions that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
Hold power tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord. Contact with a “live”wire will
make exposed metal parts of the tool “live” and shock the operator.
SERVICE

replacement parts. This will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
WARNING: Know your chop saw. Do not plug the chop saw into the power
source until you have read and understood this manual. Learn the tool’s uses and
 Following these
rules will reduce the risk of electric shock, re, or serious injury.
Always wear eye protection. Any power tool can throw foreign objects into your eyes and
cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with
ANSI safety standard Z87.1. Everyday glasses have only impact-resistant lenses. They ARE
NOT safety glasses.
SAVE THESE INSTRUCTIONS FOR REFERENCE
!
9
SAFETY GUIDELINES
SAFETY GUIDELINES
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

WARNING: Glasses or goggles not in compliance with CSA Z94.3 or ANSI Z87.1
could cause serious injury when they break.
WARNING: Always wear hearing protection and a dust mask. Use the tool
only in a well-ventilated area. Using personal safety devices and working in a safe
environment reduces the risk of injury.
DANGER: Always unplug the tool from the power source before changing the
cutting disc or when cleaning the tool.
DANGER: 
is running. Severe injury will result.
DANGER: Never install a saw blade on this tool. It is designed ONLY for use with
abrasive cut-off discs.
WARNING: Use only cut-off discs that are recommended for this chop saw and
are rated for speeds of at least 3500 RPM. Follow the instructions that accompany the
cut off discs. The use of improper cut-off discs may result in injury to the operator or
damage to the chop saw.
WARNING: If any part is missing or damaged, do not plug the tool into the
power source until the missing or damaged part is replaced.
Before using any cut-off disc, carefully read the instructions or the owner's manual for the
cut-off disc.
Use this chop saw for cutting steel only. Cutting ceramic materials will create excessive dust
and cause damage to the motor.
Always use a dust mask and safety goggles when operating the chop saw.
Always use hearing protection when operating the chop saw.
Do not wear gloves, neckties or loose clothing.
SAVE THESE INSTRUCTIONS FOR REFERENCE
!
!
!
!
!
11
Do not cut material too small to be securely held in the vise.
Always keep your hands out of the path of the cut-off disc. Avoid awkward hand positions
where a sudden slip could cause your hand to move into the path of the cut-off disc.
Secure the workpiece. Use the clamping system provided with the chop saw. It is safer than
using your hand.
Make sure there are no foreign objects in the part of the workpiece to be cut.
The cut-off disc must be securely attached as described in this manual before connecting the
tool to the power source. Failure to do so will increase the risk of serious injury if the cut-off
disc shatters or comes loose.
Make sure the guard is installed and in proper working order before operating the chop saw.
Cut-off discs must be stored in a dry location to prevent deterioration.
Before attaching the cut-off disc, inspect it for visible defects. If cracked, chipped or warped,
do not install it.
Do not over tighten the clamp nut on the cut-off disc. Excessive tightening may cause the disc
to crack, and possibly shatter, during operation.
Never turn the chop saw on with the cut-off disc touching the work surface.
Use only cut-off discs in compliance with ANSI Standard B7.1 and rated for a speed greater
than 3500 RPM.
Do not use the chop saw if the disc anges or cap screw are missing or improperly installed.
Dust and abrasive materials should not be allowed to build up in the workshop. Hot metal
sparks could start a re.
Do not remove the soft paper in the centre of the cut-off disc.
Do not alter or enlarge the centre hole of the cut-off disc, as this could result in the
disc shattering.
SAVE THESE INSTRUCTIONS FOR REFERENCE
10
!
!
SAFETY GUIDELINES
SAFETY GUIDELINES
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

EXTENSION CORD SAFETY
Make sure any extension cord used with this tool is in good condition. When using an
extension cord, be sure to use one of heavy enough gauge to carry the current the tool will
draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and
overheating.
The table below shows the correct size to use according to cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the
heavier the cord.
Be sure your extension cord is properly wired and in good condition. Always replace a
damaged extension cord or have it repaired by a qualied electrician before using it. Protect
your extension cord from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This circuit must not be less than 14
gauge wire and should be protected with either a 15A time-delayed fuse or circuit breaker.
Before connecting the power tool to the power source, make sure the switch is in the Off
position and the power source is the same as indicated on the nameplate. Running at lower
voltage will damage the motor.
SAVE THESE INSTRUCTIONS FOR REFERENCE
MINIMUM GAUGE (AWG) EXTENSION CORDS (120V USE ONLY)
Amperage rating Total length
More
than
Not more than 25’
(7.5 m)
50’
(15 m)
100’
(30 m)
150’
(45 m)
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not applicable
VVolts
AAmperes
Hz Hertz
WWatts
kW Kilowatts
Microfarads
LLitres
Kg Kilograms
HHours
2Newtons per square centimetre
Pa Pascals
OPM Oscillations per minute
Min Minutes
SSeconds
or AC
Alternating current
Three-phase current
Three-phase alternating current
with neutral
Read all safety instructions
Direct current
No load speed
Alternating or direct current
Class II construction
Splash-proof construction
Watertight construction
Protective grounding at grounding
terminal, Class I tools
Revolutions or reciprocations per
minute
Diameter
0 Off position
Directional arrow
Warning symbol
Wear safety glasses
Wear hearing protection
Wear dust mask
WARNING! Some of these symbols may appear on the chop saw. Study these symbols and learn

of this tool.
13
12
WARNING! Keep the extension cord clear of the working area. Position the cord so it
will not get caught on the workpiece, tools or any other obstructions while you are working
with the power tool.
SAFETY GUIDELINES
SAFETY GUIDELINES
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

No. Description No. Description
1 Carrying handle 8 Vise quick release nut
2Lock-off button 9 Vise adjustment crank
3 Trigger switch 10 Base
4 Arbor lock 11 Depth stop screw
5 Automatic guard 12 Swing arm locking screw
6 Cut-off disc 13 Swing arm
7 Vise mitre gauge
2
3
1
4
5
6
7
8
9
10
11
12
13
KEY PARTYS DIAGRAM
SELECTING THE WORK SURFACE
It is important to place the chop saw on a
solid, at work surface that will not shift
during operation of the chop saw. Locating
the chop saw near an electrical outlet will
eliminate the need for an extension cord.
SETTING THE DEPTH STOP
The maximum cut depth is controlled by
adjusting the depth stop.
1. Lift the swing arm (1) upward as far as
it will go.
2. Loosen the depth stop lock nut (2) by
turning it counter-clockwise using a 13
mm wrench.
3. Turn the depth stop screw (3) to raise
or lower it. Adjust until the cut-off blade
enters the base slot no more than 3/16"
(5 mm) when the swing arm is fully low-
ered and contacts the top of the depth
stop screw.
4. When the depth stop screw is correctly
set, lock it in place by tightening the
lock nut clockwise.
WARNING! Always disconnect your chop saw from the power source when replacing the cut-off
disc, clamping material in the vise, adjusting the guard, cleaning or when not in use. Disconnecting the
chop saw will prevent accidental starting that could cause serious personal injury.
WARNING! Never place the chop saw near any ammable liquids or items that can be damaged by the
sparks thrown by the chop saw during cutting. The hot sparks can ignite ammable liquids.
Hot metal sparks and sharp metal pieces will damage the work surface to some degree. Make sure you
consider this fact when selecting the work surface. A non-ammable surface, such as a metal bench, will be
less likely to be damaged during cutting.
OPERATING INSTRUCTIONS
15
14
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

CHECKING THE AUTOMATIC GUARD
The automatic guard must be checked to
ensure it is working properly.
1. Lift the guard (1) upward approximately
3" (7.5 cm) and then release it. If the
guard is functioning correctly, it will
freely drop down to its original position.
2. Lower the swing arm and cutting disc
assembly until the lower edge of the
guard (2) touches the chop saw base.
Continue to lower the swing arm and
cutting disc assembly. The automatic
guard should freely rise as the cutting
disc is lowered.
WARNING! Always disconnect your chop saw from the power source before checking
the automatic guard or the arbour cap screw.
NOTE:
The guard should always rise and fall freely when the swing arm is lowered and raised, as outlined in #1 & #2
above. If it does not, clean any cuttings out from around the guard mechanism (3).
CHECKING THE ARBOR CAP SCREW
It is important to check the arbor cap
screw to make sure the cut-off disc is fully
tightened.
OPERATING INSTRUCTIONS
1. Lift swing arm fully upward as far as it
will go.
2. Lift the disc guard (1) fully upward until
it will stay in the upright position.
3. Press and hold the arbor lock (2) to the
right while rotating the cut-off disc by
hand.
4. When the arbor lock engages the arbor,
tighten the arbor cap screw (3) by
turning it clockwise using the 8 mm hex
key supplied.
5. When the arbor cap screw is fully
tightened, remove the hex key, release
the arbor lock and lower the disc guard.
NOTE:
Only use the hex key supplied to tighten the arbor cap screw. Do NOT over tighten the arbour cap screw, as you could
crack the hub of the cutting disc.
SETTING THE MITRE VISE ANGLE
The mitre vise can be set for cutting at
angles from 90° to 45° either left or right.
1. Open the vise by turning the vise
adjustment crank (1) ve or six turns
counter-clockwise.
OPERATING INSTRUCTIONS
17
16
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

2. Loosen the mitre gauge cap screws
(2) by turning them counter-clockwise
using the 8 mm hex key (3) supplied.
3. Rotate the mitre gauge to the left or
right until the desired cutting angle (4)
lines up with the alignment mark (5).
4. Tighten both mitre gauge cap screws to
lock the mitre gauge in place.
NOTE:
Always make a test cut on a scrap workpiece to verify the mitre angle setting.
CUTTING UP TO 5" (12.7 CM) WIDE
WORKPIECES
The vise is set up at the factory for cutting
workpieces up to 5" (12.7 cm) in width. This
is the preferred set-up. If it is necessary to
cut workpieces between 5" (12.7 cm) and 7"
(17.8 cm) in width, the mitre gauge will have
to be relocated on the chop saw base.
1. Remove the front and rear mitre gauge
cap screws (1) using the 8 mm hex key
supplied.
2. Move the mitre gauge (2) back
approximately 1½" (3.8 cm) until the
hole and slot in the mitre gauge line up
with the next two holes (3) in the chop
saw base.
3. Reinstall and tighten the mitre gauge
cap screws in the two new holes.
NOTE:
To cut workpieces between 7" (17.8 cm) and 9" (22.8 cm) in width, locate the mitre gauge in the back
two holes of the chop saw base.
OPERATING THE VISE QUICK-
RELEASE
The vise has a quick-release feature that
allows for making major adjustments much
quicker.
1. To operate the quick-release system,
turn the vise crank (1) counter-
clockwise two or three turns to loosen
the vise jaws.
2. Lift upward on the front of the quick-
release nut (2) to release the vise screw
(3).
3. While holding the quick-release nut
upward in the released position, pull the
vise crank toward you to quickly open
the vise.
4. To quickly close the vise, release the
quick-release nut and push the crank
away from you.
5. Use the crank to completely tighten the
vise on the workpiece.
WARNING! 
in the vise before turning the saw On.

1. To turn the chop saw On, slide and hold
the lock-off button (1) toward you.
2. While holding the lock-off button toward
you, squeeze the trigger switch (2) until
the chop saw starts.
19
18
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

3. Once the chop-saw starts, release the
lock-off button while continuing to
squeeze the trigger switch. The motor
will stay running.
4. To turn the chop saw Off, release the
trigger switch.
REPLACING THE CUT-OFF DISC
The cut-off disc must be replaced if it
becomes damaged in any way or it has worn
down to a diameter of less than 10"
(25.4 cm).
1. Lift the swing arm fully upward.
2. Lift the guard (1) fully upward until it
exposes the arbor cap screw (2).
3. Press and hold the arbor lock (3) to the
right while rotating the cut-off disc by
hand.
4. When the arbor lock engages the arbor,
loosen the arbor cap screw by turning it
counter-clockwise using the 8 mm hex
key supplied.
5. Remove the arbor cap screw, the small
outer washer (4), the large outer washer
(5), the cut-off disc (6) and large inner
washer (7) from the arbor (8).
WARNING! Always make sure the cut-off disc is NOT touching the workpiece when
the switch is being turned On. Let the motor get to full speed before beginning to cut.
WARNING! Disconnect your chop saw from the power source before attempting to
change the cut-off disc.
6. Use a clean, dry brush or cloth to
carefully remove all cuttings from the
arbor and the motor housing.
7. Reinstall the washers, new cut-off disc
and arbor cap screw in the same order
in which they were removed.
8. Engage the arbor lock and tighten the
arbor cap screw using the 8 mm hex
key supplied.
9. Carefully rotate the cut off disk by hand
to make sure it is rmly tightened, that
it is not damaged and that it does not
wobble.
10. With depth stop properly set and the
guard in the down position, turn the
switch On.
WARNING! Reset the depth stop as shown on Page 15. The new blade will be larger and will damage
the work surface if the depth stop is not readjusted.
NOTES:
a) Make sure the LARGE outer surfaces of the large and small washers are facing the cut-off disk.
b) Make sure the ats of the washer holes slide over the matching ats of the arbor.
NOTE:
If the cut-off disc wobbles or vibrates, turn the switch Off immediately. Recheck to make sure the cut-off disc is installed
correctly and that the disc is not damaged.
21
20
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

LOCKING THE SWING ARM FOR
CARRYING
To safely carry the chop saw, it is important
to lock the swing arm and carry the tool with
the appropriate carrying handle.
1. Lower the swing arm (1) as far as it will
go.
2. Push inward on the swing arm locking
pin (2) until it engages the hole in the
swing arm.
3. Release the swing arm. It will be locked
in the DOWN position if the swing arm
locking pin is properly engaged.
4. Lift the chop saw using the rear handle
(3).
CUTTING METAL
1. Lift the swing arm fully upward as far as
it will go.
2. Adjust the mitre gauge as required.
3. Firmly lock the metal workpiece to be
cut in the vise.
4. Make sure you are wearing your
safety goggles, dust mask and hearing
protection.
5. Lower the cut-off disc until it is about 1"
(2.5 cm) above the workpiece.
WARNING! Have you read GENERAL SAFETY WARNINGS, POWER TOOL SAFETY, SPECIFIC SAFETY
RULES, EXTENSION CORD SAFETY and SYMBOLS on Pages 5 through 14 of this Instruction Manual? If
not, please do it now, before you operate this chop saw. Your safety depends on it!
Every time you use the chop saw you should verify the following:
1. Cord is not damaged.
2. Cut-off disc is correct for the type of material being cut.
3. Cut-off disc is in good condition and securely tightened onto the arbor.
4. Safety glasses, dust mask and hearing protection are being worn.
5. Guard is in good working order.
6. 
Failure to adhere to these safety rules can greatly increase the chances of injury.
23
22
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

6. While holding the chop saw handle
rmly in your right hand, turn the motor
switch On.
7. Wait for motor to get up to full speed.
Carefully lower the cut-off disc until it
contacts the workpiece.
8. Apply only slight pressure to the chop
saw handle as it begins to cut through
the workpiece. DO NOT apply too much
pressure to the handle, as this will
cause the motor to slow down, slow the
cutting action and damage the motor.
9. When the cut-off disc has completely
cut through the workpiece, release the
trigger switch immediately. Wait for
the motor to come to a complete stop
before lifting the cut-off disc away from
the workpiece.
WARNING! Never touch the workpiece immediately after a cut is completed. The metal
in the cutting area will be red hot and will cause severe burns to your skin.
NOTE:
Many sparks will be generated as soon as the cut-off disc touches the workpiece.
MAINTENANCE
REPLACING CARBON MOTOR
BRUSHES
The carbon motor brushes will wear down
and require replacing. The time intervals
between replacements will vary depending
upon the type of materials being cut and the
hours of use. It is recommended that the
brushes be checked after each 10 hours of
use. When the length of the carbon brush
reaches 1/4" (6.35 mm), the brushes should
be replaced.
1. Use a #2 screwdriver and remove
four screws (1) from the motor end cap
(2).
2. Pull the motor end cap from the motor
housing (3).
3. Use needle nose pliers to pull the spade
connector (4) from the spade.
4. Use needle nose pliers to pull the brush
retainer spring (5) away from the carbon
brush (6).
5. While holding the brush retainer spring
off the carbon brush, pull the carbon
brush out of the brush bolder (7).
6. To install a new motor brush assembly,
reverse steps 3 through 6.
Replace the second carbon brush located on
the opposite side of the motor housing using
the procedure noted above. When new motor
brushes have been installed, reinstall the
motor end cap.
WARNING! Unplug the tool from the power source before removing the motor end cap.
25
24
OPERATING INSTRUCTIONS
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I
NOTE:
The cut-off disc MUST NOT be touching the workpiece when the motor switch is turned On.

GENERAL
DO NOT use solvents when cleaning plastic
parts. Plastics are susceptible to damage
from various types of commercial solvents
and may be damaged by their use. Use a
clean cloth to remove dirt, dust, oil, grease
etc.
Keep the air vents cleared of any built-up
dust to prevent the motor from overheating.
Remove accumulated dust and debris
regularly using a soft DRY brush.
DO NOT abuse power tools. Abusive practices
can damage the tool and the workpiece.
LUBRICATION
All of the bearings in this tool are lubricated
with a sufcient amount of high-grade
lubricant for the life of the unit under normal
conditions. Therefore, no further lubrication
is required.
WARNING! DO NOT attempt to modify this chop saw or create accessories. Any such

condition leading to possible serious injury. It will also void the warranty.
WARNING! Use safety goggles when using an air jet to blow dust out of the chop saw.
WARNING! 
oils, etc. to come into contact with plastic parts. These substances contain chemicals that
can damage, weaken or destroy plastic.
WARNING! When servicing, use only identical replacement parts. The use of any other
part may create a hazard or cause damage to the product.
MAINTENANCE
EXPLODED VIEW
27
26
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

Always order by PART NUMBER, not by key number.
Key Part # Part Name Qty
19 J1G355C-019 Knob 1
20 J1G355C-020 Pin 6X32 1
21 J1G355C-021 Threaded vise shaft 1
22 J1G355C-022 Vise handle 1
23 J1G355C-023 Handle shaft 1
24 J1G355C-024 Nut base 1
25 J1G355C-025 Nut cap 1
26 J1G355C-026 Spring washer 8 2
27 J1G355C-027 Bolt M8x25 2
28 J1G355C-028 Small vise plate 1
29 J1G355C-029 Large vice plate 1
30 J1G355C-030 Pivot pin 1
31 J1G355C-031 Plain washer 16 2
32 J1G355C-032 Circlip 15 2
33 J1G355C-033 Plain washer 8 1
34 J1G355C-034 Roll pin 2.5X25 1
35 J1G355C-035 Bolt M10x20 2
36 J1G355C-036 Spring washer 10 2
Key Part # Part Name Qty
1 J1G355C-001 Inner hex head screw M8x12 1
2J1G355C-002 Nut M6 4
3J1G355C-003 Spark guard Q235 1
4J1G355C-004 Screw M6x12 2
5J1G355C-005 Plain washer 6 1
6J1G355C-006 Nut M8 4
7J1G355C-007 Spring washer 5 8
8J1G355C-008 Plain washer 5 2
9J1G355C-009 Screw M6x25 3
10 J1G355C-010 Rubber foot 3
11 J1G355C-011 Base assembly 1
12 J1G355C-012 Locating block 1
13 J1G355C-013 Bolt M8x45 1
14 J1G355C-014 Screw 1
15 J1G355C-015 Screw M5x10 6
16 J1G355C-016 Lock pin 1
17 J1G355C-017 "O" ring 6X1 2
18 J1G355C-018 Circlip 8 2
WARNING! When servicing, use only Mastercraft®replacement parts. The use of any
other parts may create a safety hazard or cause damage to the chop saw.
Any attempt to repair or replace electrical parts on this chop saw may create a safety

the toll-free helpline, at 1-800-689-9928.
PARTS LIST
Key Part # Part Name Qty
63 J1G355C-063 Bearing 80201(6201) 1
64 J1G355C-064 Rotor 1
65 J1G355C-065 Bearing 80202(6202) 1
66 J1G355C-066 Middle cover 1
67 J1G355C-067 Bearing 80029(629) 1
68 J1G355C-068 Circlip 20 1
69 J1G355C-069 Gear 1
70 J1G355C-070 Front cover 1
71 J1G355C-071 Bearing 80204(6204) 1
72 J1G355C-072 Woodruff key 4x13 1
73 J1G355C-073 Small ange washer 1
74 J1G355C-074 Screw M6x10 1
75 J1G355C-075 Nut M4 4
76 J1G355C-076 Left handle 1
77 J1G355C-077 Nut M5 3
78 J1G355C-078 Plain washer 9 1
79 J1G355C-079 Switch 1
80 J1G355C-080 Tapping screw st4.2x15 2
81 J1G355C-081 Cord anchor 1
82 J1G355C-082 Cord strain relief 1
83 J1G355C-083 Cord & plug 1
84 J1G355C-084 Screw M4x35 4
85 J1G355C-085 Right handle 1
86 J1G355C-086 Screw M5x50 2
87 J1G355C-087 Screw M5x35 1
Key Part # Part Name Qty
37 J1G355C-037 Plain washer 10 2
38 J1G355C-038 Side cover assembly 1
39 J1G355C-039 Inner hex head screw M10x20 1
40 J1G355C-040 Outer ange washer 1
41 J1G355C-041 Cut-off disc 355x3.2 1
42 J1G355C-042 Inner ange washer 1
43 J1G355C-043 Screw M5x54 4
44 J1G355C-044 Safety guard assembly 1
45 J1G355C-045 Arbor 1
46 J1G355C-046 Spindle locking pin spring 1
47 J1G355C-047 Spindle locking pin 1
48 J1G355C-048 Screw M5x85 2
49 J1G355C-049 Brush holder 1
50 J1G355C-050 Carbon brush 1
51 J1G355C-051 Brush cap 1
52 J1G355C-052 Rear cover 1
53 J1G355C-053 Screw M4x10 1
54 J1G355C-054 Plain washer 4 1
55 J1G355C-055 Washer 4 1
56 J1G355C-056 Motor cover 1
57 J1G355C-057 Torsion spring 1
58 J1G355C-058 Circlip 24 2
59 J1G355C-059 Pivot pin 1
60 J1G355C-060 Limiting block 1
61 J1G355C-061 Stator 1
62 J1G355C-062 Fan housing 1
PARTS LIST
29
28
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I

This Maste
This Mastercraft product is guaranteed for a period of 3 years from the date of original retail
purchase against defects in workmanship and materials, except for the following component:
Component A: Accessories, which are guaranteed for a period of 1-year from the date of
original retail purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with
proof of purchase within the stated warranty period and if covered under this warranty, will
be repaired or replaced (with the same model, or one of equal value or specication), at our
option. We will bear the cost of any repair or replacement and any costs of labour relating
thereto.
These warranties are subject to the following conditions and limitations:
a) a bill of sale verifying the purchase and purchase date must be provided;
b) this warranty will not apply to any product or part thereof which is worn or broken or which
has become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper
installation, operation or maintenance (as outlined in the applicable owner’s manual or
operating instructions) or which is being used for industrial, professional, commercial or rental
purposes;
c) this warranty will not apply to normal wear and tear or to expendable parts or accessories
that may be supplied with the product that are expected to become inoperative or unusable
after a reasonable period of use;
d) this warranty will not apply to routine maintenance and consumable items such as, but not
limited to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, uids, tune-ups or
adjustments;
WARRANTY
e) this warranty will not apply where damage is caused by repairs made or attempted by
others (i.e. persons not authorized by the manufacturer);
f) this warranty will not apply to any product that was sold to the original purchaser as a
reconditioned or refurbished product (unless otherwise specied in writing);
g) this warranty will not apply to any product or part thereof if any part from another
manufacturer is installed therein or any repairs or alterations have been made or attempted by
unauthorized persons;
h) this warranty will not apply to normal deterioration of the exterior nish, such as, but not
limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive
and chemical cleaners; and
i) this warranty will not apply to component parts sold by and identied as the product of
another company, which shall be covered under the product manufacturer’s warranty, if any.
Additional Limitations
This warranty applies only to the original purchaser and may not be transferred. Neither the
retailer nor the manufacturer shall be liable for any other expense, loss or damage, including,
without limitation, any indirect, incidental, consequential or exemplary damages arising in
connection with the sale, use or inability to use this product.
Notice to Consumer
This warranty gives you specic legal rights, and you may have other rights, which may
vary from province to province. The provisions contained in this warranty are not intended to
limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any
applicable provincial or federal legislation.
This product is not meant for industrial or commercial purposes. This product is for
household projects, read manual carefully.
Made in China
Imported by Mastercraft Canada Toronto, Canada M4S 2B8
WARRANTY
31
30
model no. 055-6705-8 contact us 1.800.689.9928
model no. 055-6705-8 contact us 1-800-689-9928
I
Rev 1.12 11/06/2014