AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZPAGE | 3 OF 6
A SLOPE of up to -15dB can be set between the beginning
of BIII and the end of UHF to compensate for cable losses.
0dBmeansallchannelshavethesameoutputlevel(see
previousdisplayreadout),-15dBmeansthebeginningofBIII
(174MHz) is 15dB weaker than the end of UHF.
DenetheOUTPUTLEVELoftheoutputsignal.Range
between 98dBµV and 118dBµV(defaultoutputlevelis
108dBµV).Checktheoutputviaanetworkanalyseron
the-30dBtestport.Note:Themorechannelsyouselect,
thelessinputpoweryoushouldgive(e.g.111dBµV for 10
channels).
To delete a (pair of) channel(s), position the arrow on the
channel and press the rotary button 3 seconds.
WhenyouhaveaddedallthechannelstoINPUTV/U1,and
you want to add channels to the other inputs, scroll up to
the top of the menu (to INPUT V/U 1), tap the button and
scroll to the next input.
Repeatthepreviousstepsforallinputchannels.
Output Settings
To add another (group of) channel(s), scroll down to ADD
CHANNELandtaptoconrm.
Topreventbadqualityorscrambledimages,makesurethat
only one input channel is assigned to one output channel. If
2 channels are assigned to the same output channel, a star
(*) will appear.
The same applies for adding multiple channels. Make sure
that each output channel is selected only once.
Afterthis,thecorrectLTElterwillbesetfortheUHF
inputs(possibleltersare694MHz,790MHzorOFF).Ifthe
channelsarelowerthan48,the694MHzlterisactivated.
The790MHzlterisactivatedforthechannelslowerthan
60.
Delete a (pair of) Channel(s)
Note1:Thevalue85dBµV (in the bottom right corner)
indicatestheincominglevelofthechannel.
Note2:ForEU,ItalyandNewZealandregion,Channel13
(230-240MHz)canbeused.CH13cannotbeconverted.
Note3:Astar(*)willappearwhenconvertingtoadifferent
channelbandwidth:e.g.froma7MHzchanneltoan8MHz
channel
For optimal performance we recommend to only add single
channels, unless you need to process a lot of channels.
VHFATTN:Tocompensateforcablelosses,anattenuator
ofupto15dBcanbeconguredtodecreasetheVHF(up
to300MHz)andDABoutputlevel(comparedtotheUHF
outputlevel(above300MHz)).
Note:IntheOUTPUTmenu,youdenetheoutputlevelin
dBµVoftheMUX’s.TheProlerRevolutionhasenoughgain
toguaranteethisoutputlevelunderallinputconditions.
Incaseaslopehasbeenset,theoutputlevelindicatedon
thedisplaywillbetheoutputlevelofthehighestfrequency
MUX.
Advanced Settings
ThelanguageoftheProlerRevolutioncanbesetto
English, Italian, Spanish or French.
TapREGIONtochecktowhichregion/countrytheProler
Revolutionisset.Tochangetheregion/country,ahardreset
is required. (see region/country settings)
DeneDCVOLTAGEfortheinputs,choosebetween12V
or 24V. This is a global setting for all inputs, each input can
thenbeswitchedbetweenOFForthisvalue.Allcountries
are set by default on 24V, except UK which is set by default
on 12V.
Thelterbandwidthcanbechangedfrom-2000kHzto
0 kHZ in steps of 250 kHz. This allows you to optimize
thebandwidthofyourlter.Forinstance,aEuropean8
MHz channel can be changed from 6 to 8 MHz. The default
setting is -750 kHz, which is an optimal setting in 95% of the
cases.
S-BandchannelscanbeactivatedinAdvancedMode.By
default,theyarenotactivated.
See NOTE below for more explanation.
