Matrix Telecom SETU VTEP User manual

SIP Trunking with Elastix
Configuration Guide for Matrix SETU VTEP

SETU VTEP configuration guide for Elastix Page | 2
Contents
Setup Diagram 3
SIP Trunk Configuration in Elastix for SETU VTEP 4
Outgoing Call configuration in Elastix 7
Incoming call configuration in Elastix 9
SIP Trunk Configuration in SETU VTEP for Elastix 11
E1 to SIP Routing Configuration in SETU VTEP 18
FAX Configuration in SETU VTEP 20
FAX Configuration in Elastix 21
Viewing SIP Trunk Status in SETU VTEP 21

SETU VTEP configuration guide for Elastix Page | 3
Set Up Diagram:
(Note : PRI line from PBX is terminated to VTEP as per above setup diagram)
Host Server Environment Details
Description
Server OS
CentOS release 5.7 (Kernel 2.6.18-274.e15 on an i686)
Software Type
Elastix 2.4.0
Software version
Elastix (2.4.0)
Elastix-2.4.0-Stable-i386-bin-04Feb2013
Test Setup Equipment:
Equipment
Model
Version
SETU VTEP
N/A
V1R9
Analog Telephone
N/A
N/A

SETU VTEP configuration guide for Elastix Page | 4
SIP Trunk configuration in Elastix for SETU VTEP
Open the Web GUI of Elastix server in web browser as shown below (IP of server will be
same as IP of System on which Elastix is installed).
http://192.168.51.6/admin/config.php# (here, 192.168.51.6 IP is allocated for Elastix WEB
GUI access)
Enter username & password as entered while installing Elastix.
Default username: admin, Password: admin
On Successful login home Page opens
On the top of the screen, click on PBX Configuration menu. To add a Trunk select Add
SIP Trunk in Trunk menu

SETU VTEP configuration guide for Elastix Page | 5
In Trunk Name field configure Type as VTEP
In CID Options field configure as Allow Any CID
Configure Maximum Channels as 8
In Dialed Number Manipulation field configure desired number pattern which has to be
routed via VTEP ( 1. Used in this example, all Outgoing numbers with prefix 1 has to be
routed via VTEP)
In Outgoing Settings, configure Trunk Name as vtep.
Configure PEER Details
ohost=***provider ip address***
provider ip address is the IP address of VTEP. (i.e. 192.168.51.238)
otype=peer
Peer to Peer trunk between VTEP and Elastix
odtmfmode=rfc2833
DTMF detection and Out-dial mode is set to rfc2833(OUTBAND)
Click on Submit changes.

SETU VTEP configuration guide for Elastix Page | 6
Click on Apply Configuration Changes Here
New configuration setting will be saved and Elastix will be reloaded

SETU VTEP configuration guide for Elastix Page | 7
Outgoing Call Configuration in Elastix:
Open Outbound Routes.
In Route Name field configure any desired Rule Name ( interop name used in this
Example)
In Dial Pattern field configure desired number pattern which has to be routed via VTEP
(_1. Used in this example, all Outgoing numbers with prefix 1 has to be routed via VTEP)
Prefix can be used before dialing the desired number. ( 9 used in this example)
Configure desired caller id in Caller ID field
In Trunk Sequence for Matched Routes configure the SIP trunk which we created.(In
this example, we have created VTEP)
Click on Submit Changes and Apply Configuration Changes Here as well.

SETU VTEP configuration guide for Elastix Page | 8

SETU VTEP configuration guide for Elastix Page | 9
Incoming Call Configuration in Elastix:
Open PBX Configuration. Click on Inbound Routes
Configure Description field as name of Incoming route. (In this example it is configured
as Incoming_VTEP )
Set Destination for Incoming call Router ( selected 7700 extension in Example)
Click on Submit
Click on Apply Configuration Changes Here.

SETU VTEP configuration guide for Elastix Page | 10