Matrox Monarch User manual

Matrox Monarch Device Setup
Step 1 -- Powering up the Monarch and setting the IP mode
On initial power up, Monarch automatically boots in DHCP IP mode to connect to a DHCP-enabled network, but
you can force Monarch to boot in Static IP mode (169.254.1.11)* if there is no DHCP network available.
Power up the Monarch by connecting the external power supply to an AC outlet. The following will occur:
Note When you power off the Monarch, the device maintains the previously-selected IP mode.
Step 2 -- Connecting to a network and finding the IP address
Option 1 -- Connecting to a network with a DHCP server
A DHCP-enabled network will assign the Monarch an IP address. Use one of these methods to find the address:
•HDMI Monitor Connect an HDMI monitor to the Monarch’s HDMI output, and then power up the
device. The IP address is displayed on-screen for 30 seconds before the passthrough signal is displayed.
•USB device Connect a USB device to the Monarch’s USB 2 port, and then reboot the device. The device’s
current IP address and status will be automatically copied to the USB device as a .txt file.
•Matrox Monarch Utils Use the Monarch Utils application (available for HD, HDX, and LCS on both
Mac OS and Windows). This is useful when you are not physically near the device:
aConnect an Ethernet cable from the Monarch’s LAN port to a network port.
bDownload the appropriate Matrox Monarch Utils (HD, HDX, or LCS) from the Matrox website at
www.matrox.com/video/support, and then copy it to a computer on the same subnet as your Monarch device.
cRun the Utils application file to open the application. If Universal Plug and Play (UPnP) is enabled on your
network, Utils will automatically scan for Monarch devices. To scan manually, click the Find All button.
•Matrox Monarch LCS Radar Matrox Monarch LCS users can download the Matrox Monarch LCS
Radar monitoring application and its accompanying documentation from www.matrox.com/video/support.
DHCP
(Default behavior)
*To set to Static IP
(Optional)
Monarch is ready
to use when...
If you have a
Monarch HD All LEDs illuminate
After the Record LED flashes
for three (3) seconds, press the
RECORD button on the device.
All LEDs are off except for
Power ( ), Stream,
Record, and USB 1
If you have a
Monarch HDX
Various LEDs, including
the Warning ( )LED,
flash on and off
After the Encoder 2 LED flashes
for three (3) seconds, press the
ENCD 2 button on the device.
The Warning ( ) LED
stops flashing. If the
Warning LED remains
on, consult the user
guide for your Monarch
device for information.
If you have a
Monarch LCS
Various LEDs, including
the Warning ( )LED,
flash on and off
After the ENCD LED flashes
for three (3) seconds, press the
ENCD button on the device.

Matrox is a registered trademark and Monarch is a trademark of Matrox Electronic Systems Ltd. Windows is a registered trademark of
Microsoft Corporation. Mac OS is a registered trademark of Apple Inc.
F11383-501-0200 Copyright © 2018 by Matrox Electronic Systems Ltd. All rights reserved. Printed in Canada.
Option 2 -- Connecting to a network without a DHCP server
A network without a DHCP server does not assign an IP address to the Monarch device. You must assign the
Monarch a static IP address, and then configure your computer’s network to allow it to connect to the Monarch.
The default Monarch IP address in Static IP mode is 169.254.1.11.
1Connect the Monarch to your computer using one of the following methods:
$Connect an Ethernet cable from the Monarch’s LAN port to your computer’s Ethernet port.
$Connect an Ethernet cable from the Monarch’s LAN port to your computer’s network switch.
2Change your computer’s IP address and subnet mask to the following:
$IP address 169.254.1.10
$Subnet mask 255.255.0.0
Your computer will now be able to connect to the Monarch using the default static IP address 169.254.1.11. For
more information on how to change these settings on your computer, see your operating system’s documentation.
If you have multiple Monarch devices on the same network, they must each have unique IP addresses. You can
change the IP address from the Command Center.
Step 3 -- Accessing the Command Center
You configure and control Monarch devices from the Command Center.
1Access the Command Center by using one of the following methods:
$From your web browser, enter the Monarch device IP address in the address field, and then press ENTER.
$If you have Utils open, double-click any of the listed devices to open the Command Center for that device.
$(Monarch LCS only) You can use the Matrox Monarch LCS Radar application to access the Command
Center of any Monarch LCS device on the network. Download the application and its accompanying
documentation from www.matrox.com/video/support.
2Log in to the Command Center. Click a menu item on any Command Center page other than the Status
page, and then enter the default Username (admin) and Password (admin).
3Connect your input/output devices to the Monarch, then configure it as needed (see the documentation for
your Monarch device available at www.matrox.com/video/support).
Getting the latest firmware, documentation, and utilities
To ensure that you have the latest firmware for your Monarch device, firmware updates are available on our
website at www.matrox.com/video/support. You can view the current firmware version of your Monarch device
in the Command Center (Device > About).