Mattel BOOMco Rapid Madness User manual

CAUTION: Do not aim at eyes or face.
TO AVOID INJURY: Use only darts
designed for this product.
Do not modify darts or dart blaster.
Please keep these instructions for future reference as they contain important information.
GAUNTLET
INSTRUCTIONS
CONTENTS
1
SHIELDS
2
ATTACHING TARGETS
6
CLEANING DARTS
8
REPLACING TARGETS
& SHIELDS
9
1
4
WARNING: Do not aim at eyes or face. Only use
projectiles supplied with this toy.
Do not fire at point blank range.
Always wear appropriate eye-wear,
sold separately.
x 30
INSTRUCTION SHEET
SPECIFICATIONS
Toy:
Toy No.:
Part No.:
Trim Size:
Folded Size:
Type of Fold:
# colors:
Colors:
Paper Stock:
Paper Weight:
EDM No.:
DATE:
REV. DATE:
Y8618
RAPID MADNESS
0920
A4
A5
70 gsm
One
black
FSC recycled paper
10.22.13
11.15.13
REMOVING DARTS
7
IMPORTANT:
Always remove darts from target after play.
Keep one hand pressed on target, hold dart
by the tip and gently peel dart off.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations
1-800-524-8697. Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty.,
Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th
Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia. Tel:[phone], Fax:[phone].
Y8618-0920
✖ Do not stick target to walls or furniture as
it may cause damage to the surface.
Peel backing off target before sticking it to surface.
Dust, dirt, and other debris can cause darts to lose
their adhesiveness.
To clean darts, rinse darts’tips with tap water or use
tape to remove excess debris.
NOTE: Dry darts before using again.
Y8620/BBY17
Replace time-worn targets and shields with
Y8620/BBY17 SMART STICK REFILLS.
Each sold separately, subject to availability.
a
b
Click!
Detach shields as desired.
B. To close shields.
A. Activate shields.

A. Fully load clip with darts.
PERFORMANCE TIPS
3
2
E. Pull and hold trigger for rapid fire.
B. Insert the fully loaded clip from the left
side of the blaster with the arrowheads
pointing right.
Pump sliding handle all the way forward and all the
way back up to 18 times for maximum fire power.
C.
D. Pull trigger and release quickly for single fire.
A. Remove empty clip from blaster. B. Press RESET button and trigger.
Hold to release all air from blaster
IMPORTANT:
Release all air from
blaster when not in use.
Check if the remainder of the clip is loaded. Rapid fire will stop at empty slots. Press and release
RESET button to advance to loaded slots, then pull and hold trigger to continue firing.
A.
Pump sliding handle again until there is resistance, then pull and hold trigger to continue firing.
B.
3
TO FIRE
4
RESET
If rapid fire suddenly stops, try doing the following:
Click!
TOP VIEW
abAlign to blaster as shown.
18x
a
IMPORTANT INFORMATION
Read Carefully!
IMPORTANT INFORMATION
Read Carefully!
5
b
RESET BUTTON