Mattel RoseArt Charminis Jewelry Studio User manual

Jewelry Studio
Please remove everything from the package and compare
to the contents list. If items are missing, please contact
Customer Service: 1-800-CRAYONS (US & Canada).
Keep these instructions for future reference as they
contain important information.
1 Jewelry Tree
1 Mini Brush
6 Nylon Cords
1 Glaze Pot
2 Safety Clasps
52 Charm Pieces
15 Jump Rings
ASSEMBLING THE CHARMINIS™JEWLERY TREE
BEFORE YOU BEGIN
Protect play surfaces before use
Make sure hands are dry before use
Wash hands with soap and water after play
Keep charm pieces from being exposed to high humidity or water while storing
Drain, rinse, clean and dry all items thoroughly before storing
STEP 1: Insert the Center Piece into
the Base.
STEP 2: Add Arms to Center Piece.
Ensure the hooks are facing down.
STEP 3: Align bottom of Heart
Topper with opening on top of
Center Piece. Snap together to
secure into place.
STEP 4: Open and remove charm pieces from bags and place in Base. Keep the bags to store un-used
pieces for future use. Place Glaze Pot in small circular space on Base. See fully assembled Jewelry Tree
Stand above.
Arms
Center Piece
Heart
Topper
Base
Mini Brush
Storage
Tray
Glaze Pot

INSTR-FHM92
GLAZING YOUR CHARM
STEP 1: Glazing your Charm: Open the Glaze
Pot. Using your nger hold your charm by
the jump ring. Brush glaze on ALL sides of
charm.
STEP 2: Place your charm on a piece of wax
paper and allow to dry for approximately
25 minutes.
TIPS
F
o
r
m
o
r
e
c
r
e
a
t
i
v
e
a
c
t
i
v
i
t
i
e
s
v
i
s
i
t
GLAZE CONFORMS TO ASTM D4236.
Keep this information. Colors and decorations may vary.
© 2017 & ® & ™, Mattel-MEGA Holdings (US), LLC.
All rights reserved. MADE IN CHINA.
Mattel Sales Corp., 333 Continental Boulevard, El Segundo, CA 90245, USA.
Consumer Services: 1-800-CRAYONS (US & Canada).
CONFORMS TO THE SAFETY REQUIREMENTS OF ASTM F963 & F2923.
CREATING YOURCHARM
STEP 1: When handling charm pieces
make sure your hands are dry. Select
the pieces you want to use to build
your charm. Using the water bottle
and brush, apply a small amount of
water to the area you want to add a
piece. Hold pieces together for approxi-
mately 30 seconds and watch them
magically fuse!
STEP 2: Repeat step 1 for stacking and
fusing pieces together to complete your
charm.
TIP: For best adhesion strength between
two charm pieces, make sure to add water
and connect on the largest surface area
on each charm piece.
TIP: Create
unique combi-
nations of
stacked pieces
or refer to the
package for
design ideas.
STEP 3: To nish building your charm, add
the jump ring by applying a small amount
of water to the ring and hold it against
the charm for approximately 30 seconds.
Next, hang your charm on a hook of the
Jewelry Tree and allow charm to dry for
approximately 20 minutes. The charm is
dry when it is no longer sticky to the
touch.
Be creative! Braid or loom the cord before
adding any charm pieces.
Add as many charms as you desire by
lacing the cord through the jump rings of
your charms.
To make a bracelet, follow the same steps
as making a necklace, but use a shorter
piece of cord. Use a clasp or simply tie a
knot.
STEP 1: Cut a piece of the Cord to the
desired length and tie a knot on one
end. Next, using the un-knotted end,
thread the cord through one side of
the Safety Clasp and pull until the
knot you created is hidden inside the
clasp piece.
STEP 2: Once you have added your
charms onto the cord, thread and knot
the second half of the Safety Clasp on
the cord to complete your necklace.
Make sure the clasp “snaps” together
for secure closure. Now you are ready
to wear your Charminis™ necklace!
CREATING A CHARMINIS™NECKLACE
www.Charminis.com
service.mattel.com
?
Adhere
at side of
jump ring
to charm.
KEEP CHARMS AWAY FROM WATER.