Max Rebartier RB398S Operator's manual

㻌
㻌㻌
㻌
RB398S(CE) RB518(CE) RB218(CE)
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
MODE D'EMPLOI ET CONSIGNES DE SÉCURITÉ
MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD
BEDIENUNGSANLEITUNG UND SICHERHEITSANWEISUNGEN
MANUALE D'USO E ISTRUZIONI PER LA SICUREZZA
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ И ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ
REBAR TYING TOOL
OUTIL DE LIGATURE DE BARRES
ATADORA DE ARMADURAS DE REFUERZO
BEWEHRUNGSSTAHL-BINDEWERKZEUG
UTENSILE PER LA LEGATURA DEI FERRI D'ARMATURA
ИНСТРУМЕНТ ДЛЯ ОБВЯЗЫВАНИЯ АРМАТУРНЫХ СТЕРЖНЕЙ
INDEX ENGLISH Page 6 to 17
SOMMAIRE FRANÇAIS Page 18 à 30
ÍNDICE ESPAÑOL Página 31 a 43
INHALTSVERZEICHNIS DEUTSCH Seite 44 bis 56
INDICE ITALIANO Pagina 57 a 69
СОДЕРЖАНИЕ РУССКИЙ Страница 70 - 83
RB398S RB518 RB218
Before using the tool, read and understand tool labels and manual. Failure to follow warnings could result
in serious injury. Keep these instructions with the tool for future reference.
Veillez à lire et bien comprendre les étiquettes et le manuel avant d'utiliser cet outil. Tout manquement au
respect des avertissements peut entraîner des blessures graves. Conservez ces instructions avec l'outil
pour toute consultation ultérieure.
Lea y comprenda las etiquetas y el manual de la herramienta antes de usarla. El incumplimiento de las
advertencias puede provocar lesiones graves. Conserve estas instrucciones junto con la herramienta para
futuras consultas.
Lesen Sie vor der Verwendung des Werkzeugs alle Beschriftungen von dem Werkzeug und die Anleitung
sorgfältig durch. Das Nichtbefolgen der Warnungen kann zu schweren Verletzungen führen. Bewahren
Sie diese Anweisungen zum späteren Nachschlagen mit dem Werkzeug zusammen auf.
Prima di utilizzare l'utensile, leggere e comprendere le etichette e il manuale dell'utensile. La mancata
osservanza delle avvertenze potrebbe risultare in gravi lesioni personali. Conservare queste istruzioni
insieme all'utensile per consultazioni future.
Перед эксплуатацией инструмента внимательно прочитайте данное руководство инаклейки на
инструменте; убедитесь, что Вы их правильно понимаете. Игнорирование приведенных
предупреждений может привести кполучению серьезных травм. Храните эти инструкции вместе с
инструментом для обращения кним вбудущем.
WARNING
AVERTISSEMENT
ADVERTENCIA
WARNUNG
AVVERTENZA
ОСТОРОЖНО
All manuals and user guides at all-guides.com

Fig.4 Fig.5
Fig.7 Fig.8 Fig.9
⑱
⑩
②③
Fig.2 Fig.3
Fig.1
⑭
⑬⑯
⑮
⑫
①
②
③④⑤⑥
⑦
⑧
⑪⑨
⑩
⑱
⑲
Fig.6
⑧
⑦
⑩
⑪
⑧
⑲
⑳
⑰
2
All manuals and user guides at all-guides.com

⑤
23
⑧
22
②
③
Fig.10 Fig.11 Fig.12
Fig.13 Fig.14 Fig.15
Fig.16 Fig.17 Fig.18
Fig.19 Fig.20 Fig.21
⑯
⑭
⑯
⑭
23
24
22
45°
Fig.22 Fig.23 Fig.24
⑬
⑬
⑬
⑬
⑬
3
All manuals and user guides at all-guides.com

a
①
25
Fig.25 Fig.26
26
29
27
28
Fig.27
Fig.28 Fig.29 Fig.30
Fig.31 Fig.32 Fig.33
Fig.34 Fig.35 Fig.36
30
27
26
28
29
24
30 32
33
29
31
28
26
27
25
25
b
c
4
All manuals and user guides at all-guides.com

Fig.37 Fig.38 Fig.39
Fig.40 Fig.41 Fig.42
Fig.43 Fig.44 Fig.45
Fig.46
41
35
⑤⑤
110
34 34
35
36
37 39 38
40
36
42
38
40
39
39
40
44
43
35
41
38 38
5
All manuals and user guides at all-guides.com

6
INDEX
1. NAME OF PARTS ............................................................................................................................................. 6
2. LIST OF CONTENTS......................................................................................................................................... 7
3. GENERAL POWER TOOL SAFETY WARNINGS............................................................................................7
4. RB398S/RB518/RB218 SAFETY FEATURES.................................................................................................. 8
5. TOOL SPECIFICATIONS AND TECHNICAL DATA ...................................................................................... 10
6. TECHNICAL DATA ......................................................................................................................................... 11
7. PRODUCTION YEAR ...................................................................................................................................... 11
8. WIRE SPECIFICATION ................................................................................................................................... 12
9. APPLICATIONS .............................................................................................................................................. 12
10. APPLICABLE REBAR SIZE ........................................................................................................................... 12
11. BATTERY INSTRUCTIONS ............................................................................................................................ 13
12. OPERATING INSTRUCTIONS........................................................................................................................ 14
13. MAINTENANCE............................................................................................................................................... 15
14. CLEANING MANUAL...................................................................................................................................... 15
15. STORAGE ....................................................................................................................................................... 15
16. TROUBLE SHOOTING/REPAIRS................................................................................................................... 16
DEFINITIONS OF SIGNAL WORDS
WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates a property damage message.
1. NAME OF PARTS
Fig.1 Fig.2 Battery pack
Fig.3 Battery charger
Refer to the JC925A operating and maintenance manual.
Fig.13 to Fig.46
ENGLISH
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
1Arm
2Release stopper
3Release lever
4Window
5Torque dial (RB398S)
Torque and wrap dial (RB518)
Feed dial (RB218)
6LED
7Main switch
8Trigger lock
9Grip
0Battery pack
aTrigger
bCurl guide
cTiewire
dReel stopper
eProduction year and number
fReel holder
gBelt hook
hLatch
iPack cap
jTerminal
lFeeding gear
mWire Guide
nPipe
oHexagon socket head bolts M3 × 6
pCutter
qWire guide A
rFixed cutter
sCutter plate unit
Original instructions
All manuals and user guides at all-guides.com

7
2. LIST OF CONTENTS
• MAX REBAR TYING tool
• Lithium ion Battery pack / JPL91440A
• Lithium ion Battery charger / JC925A
• Power cord
• INSTRUCTION MANUAL AND SAFETY
INSTRUCTIONS (This book)
3. GENERAL POWER TOOL SAFETY
WARNINGS
1. Work area safety
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
• Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
•Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
•Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
•Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
•Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
•Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
•Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
tArm B
uCutter connecting rod hole
vgroove
wWire guide B
xedge
yHexagon socket head bolts M3 × 5
zArm B
AWire guide A
BStep pin
CFixed cutter
DCutter
EWasher
FConnecting rod
GLarge hole
HSmall hole
READ ALL SAFETY WARNINGS AND ALL
INSTRUCTIONS.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury. Save all warnings
and instructions for future reference. The term "power
tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WARNING
All manuals and user guides at all-guides.com

8
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
•Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
•Do not use the power tool in the rain, where water is
splashing, in a wet place, or in a damp place. Using the tool
in these or similar conditions will increase the risk of electric
shock, dangerous malfunction, and overheating.
•DO NOT DISPOSE OF BATTERY PACKS/BATTERIES
INTO FIRE OR WATER. Battery packs/batteries should be
collected, recycled or disposed of in an environmental-friendly
manner.
•PROTECT THE BATTERY AGAINST HEAT, ALSO
AGAINST CONTINUOUS SUN IRRADIATION AND FIRE.
There is danger of explosion.
•CHARGE THE BATTERY PACK IN A TEMPERATURE
RANGE 5°C (41°F) TO 40°C (104°F).
•DO NOT DISPOSE OF POWER TOOLS INTO HOUSEHOLD
WASTE. According to the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are no
longer usable must be collected separately and disposed of in
an environmentally correct manner.
•DEFFECTIVE OR DEAD OUT BATTERY PACKS/
BATTERIES MUST BE RECYCLED ACCORDING TO THE
GUIDELINE 2006/66/EC.
4. RB398S/RB518/RB218 SAFETY
FEATURES
1. INSPECT THE PARTS BEFORE MOUNTING THE
BATTERY PACK
•Examine the screws to make sure they are securely
tightened.
Incomplete tightening may result in an accident or
breakage. If a screw is loose, retighten it completely.
•Inspect parts for damage.
Parts will wear over periods of use. Look also for missing
and defective parts and for parts of poor quality. If a part
must be replaced or repaired, purchase the replacement
part at the dealer where the tool was purchased or MAX
CO., LTD. authorized distributors.
Use only genuine authorized replacement parts.
2. SET THE MAIN SWITCH (FIG.6.7) AT "OFF", THE
TRIGGER LOCK (FIG.6.8) AT "LOCK" AND
REMOVE THE BATTERY PACK (FIG.6.0), WHEN
CHANGING THE BATTERY PACK, REPLACING OR
ADJUSTING THE TIEWIRE, ABNORMALITIES
OCCUR, AND THE TOOL IS NOT BEING USED
Leaving the tool switched on in these situations may cause
breakdowns or damage.
3. KEEP FINGERS AND BODY PARTS CLEAR
BETWEEN THE ARM AND CURL GUIDE AT ALL
TIMES (FIG.16)
Failure to do so may result in serious injury.
4. KEEP FINGERS AND BODY PARTS AWAY FROM
THE TIEWIRE WHEN TOOL IS IN OPERATION
Failure to do so may result in serious injury.
5. DO NOT POINT THE TOOL AT ANYONE
Personal injury may result if the tool catches an operator or
anyone working near him/her. While working with the tool, be
extremely careful not to bring hands, legs, and other body
parts near the arm of the tool.
6. WHEN THE TOOL IS NOT IN OPERATION KEEP
YOUR FINGERS OFF THE TRIGGER
Failure to do so may cause accidental tying, leading to
serious injury.
7. NEVER OPERATE THE TOOL UNDER ANY
ABNORMAL CONDITION
If the tool is not in good working order, or if any abnormal
condition is noticed, switch it off immediately (set the Main
switch at "OFF"), lock the Trigger and have it examined and
repaired.
8. AFTER BATTERY INSTALLATION IF THE TOOL
OPERATES WITHOUT THE TRIGGER BEING
PULLED OR THE OPERATOR NOTICES UNUSUAL
HEAT, SMELL, OR SOUND, DISCONTINUE
OPERATION
Failure to do so may lead to serious injury. Return to dealer
for safety inspection.
9. NEVER MODIFY THE TOOL
Modifying the tool will impair performance and operating
safety. Any modification may lead to serious injury and void
the tool warranty.
10. MAINTAIN THE TOOL IN GOOD OPERATING
CONDITION
To secure operating safety and ensure top performance,
keep the tool free of wear and damage. Also keep the tool's
hand grip dry and clean, especially free of oil and grease.
All manuals and user guides at all-guides.com

9
11. USE ONLY THE AUTHORIZED BATTERY PACK
If the tool is connected to a power supply other than the
authorized pack, such as a rechargeable battery, a dry cell,
or a storage battery for use in automobiles, the tool may be
damaged, break down, overheat, or even catch on fire. Do
not connect this tool to any power supply except the
authorized battery pack.
12. TO ENSURE MAXIMUM PERFORMANCE, FULLY
CHARGE THE BATTERY BEFORE USE
A new battery pack or one not used for extended periods
may have self-discharged and thus may need recharging to
restore it to a fully charged condition. Before operating the
tool, make sure to charge the Battery pack with the
designated MAX Battery charger.
13. BATTERY CHARGING PRECAUTION
13-1 Use only MAX Battery charger and MAX
Battery pack.
Failure to do so may cause the Battery to overheat or
catch fire leading to serious injury.
13-2 Charge the Battery from AC between 100V
and 240V wall sockets.
Failure to do so may result in overheating, or
inadequate charging possibly causing serious injury.
13-3 Never use a transformer.
13-4 Never connect the Battery charger to an
engine generator direct-current power
supply.
The charger will break down or be damaged from
burning.
13-5 Avoid charging the Battery pack in the rain,
in a damp place, or where water is
splashing.
Charging a damp or wet Battery pack will cause an
electric shock or a short circuit that may lead to
damage from burning and even the tool catching on
fire.
13-6 Do not touch the power cord or plug with a
wet hand or glove.
This may cause injury from electric shock.
13-7 Do not put a cloth or any other cover on the
Battery charger while the Battery pack is
being charged.
This will cause overheating and damage from burning,
or the Charger may even catch fire.
13-8 Keep the Battery pack and Battery charger
away from heat and flames.
13-9 Do not charge the Battery pack near
flammable materials.
13-10 Charge the Battery pack in a well ventilated
place.
Avoid charging the Battery pack where it will be in
direct sunlight.
13-11 Charge the Battery pack in a temperature
range of 5°C (41°F) to 40°C (104°F).
13-12 Avoid continual use of the Battery charger.
Rest the Charger for 15 minutes between charges to
avoid functional trouble with the unit.
13-13 Any objects that block the ventilation holes
or Battery pack receptacle may cause
electric shock or functional troubles.
Operate the charger free of dust or other foreign
materials.
13-14 Handle the power cord carefully.
Do not carry the Battery charger by its power cord. Do
not use the power cord to disconnect it from a wall
socket; this will damage the cord and break the wires
or cause a short circuit. Do not let the power cord
contact sharp edged tools, hot materials, oil, or
grease. A damaged cord must be repaired or
replaced.
13-15 Do not charge non rechargeable batteries
with this charger.
13-16 This charger is not intended for use by
children or disabled persons without
supervisor.
13-17 Children should be supervised to ensure
that they do not play with the charger.
13-18 Put a Pack cap (Fig.2.i) on the Terminal
(Fig.2.j) of the Battery pack.
When the Battery pack is not in use, put a Pack cap on
its Terminal to prevent short circuits.
13-19 Do not let the Terminal (metal component)
of the Battery pack short-circuit.
A short circuit in the Terminal will generate a large
current, causing to overheat the Battery pack and
become damaged.
13-20 Do not leave or store the tool in a vehicle or
in direct sunlight during summer. Leaving
the tool in high temperature conditions
may cause the Battery pack to deteriorate.
13-21 Do not store a fully discharged Battery
pack. If a fully discharged Battery pack is
removed from the system and left for a
long period of time, it may become
damaged. Recharge the Battery
immediately when it has been discharged.
14. WEAR SAFETY GLOVES WHILE OPERATING THE
TOOL
The finish tie has sharp edges. To avoid serious injures, be
careful not to touch the sharp edges. MAX recommends
wearing safety gloves while operating the tool.
15. PRIOR TO USING THE TOOL
(Fig.4 and 5) Make sure that the safety features function
properly. If they do not, avoid using the tool.
All manuals and user guides at all-guides.com

10
5. TOOL SPECIFICATIONS AND TECHNICAL DATA
<BATTERY CHARGER>
<BATTERY PACK>
PRODUCT DESCRIPTION MAX Rebar Tying tool
PRODUCT NO. RB398S(CE) RB518(CE) RB218(CE)
DIMENSIONS (Battery pack included) (H)305mm (12'')
(W)105mm (4-1/8'')
(L)290mm (11-3/8'')
(H)305mm (12")
(W)105mm (4-1/8")
(L)305mm (12")
(H)305mm (12")
(W)105mm (4-1/8")
(L)270mm (10-5/8")
WEIGHT (Battery pack included) 2.4kg / 5.3lbs
BATTERY Li-ion 14.4V/(JPL91440A)
OPERATING TEMPERATURE -10°C to 40°C / 14°F to 104°F
HUMIDITY 80% RH or less
PRODUCT DESCRIPTION Lithium ion Battery charger
PRODUCT NO. JC925A
INPUT AC100-240V 50/60Hz 2.2A
OUTPUT DC14.4V 4A, DC18V 4A, DC25.2V 2.8A
WEIGHT 0.7kg / 1.6lbs
OPERATING TEMPERATURE RANGE 5°C to 40°C / 41°F to 104°F
OPERATING HUMIDITY RANGE 80% RH or less
PRODUCT DESCRIPTION Lithium ion Battery pack
PRODUCT NO. JPL91440A
NOMINAL VOLTAGE DC14.4V(3.6V x 4cells)
NOMINAL CAPACITY 3.9Ah (3,900mAh)
CHARGING TIME Approx. 50min.(Approx. 80% of capacity)
Approx. 65min.(100% of capacity)
ACCESSORIES Pack cap (For preventing short circuit)
WEIGHT 0.5kg / 1.1lbs
CHARGING TEMPERATURE 5°C to 40°C / 41°F to 104°F
OPERATINGTEMPERATURE RANGE 0°C to 40°C / 32°F to 104°F
OPERATING HUMIDITY RANGE 80% RH or less
TIES PER CHARGE
(*under the following conditions: normal
temperature, unused, full-charged battery)
RB398S(CE) RB518(CE) RB218(CE)
Approx. 3,500 ties (3 Wraps/tie) Approx. 2,400 ties
(4 Wraps/tie) Approx. 2,200 ties Approx. 3,000 ties
All manuals and user guides at all-guides.com

11
6. TECHNICAL DATA
1NOISE
Measured value according to EN 60745:
A-weighted sound pressure level (LpA): 79 dB
Uncertainty (KpA): 3 dB
A-weighted sound power level (LWA): 90 dB
Uncertainty (KWA): 4.5 dB
2VIBRATION
Measured value according to EN 60745:
Vibration total values (ah): 2 m/s2
Uncertainty (K): 1.5 m/s2
The following information:
• The declared vibration emission value has been measured in accordance with the standard test method and may be used for
comparing one tool with another.
• The declared vibration emission value may also be used in a preliminary assessment of exposure.
• The vibration and noise emissions during actual use of the power tool can differ from the declared values depending on the ways
in which the tool is used especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of
use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in
addition to the trigger time).
3 RADIATED EMISSION 30-1000 MHZ Class A
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
4 Overvoltage category - category 1 according to IEC 60664-1
5 Pollution degree - degree 4 according to IEC 60664-1
6 Design guidelines – Machinery directive annex 1, EN60745-1, EN60745-2-18
7. PRODUCTION YEAR
This product bears production number in the body. The two digits of the number from left indicates the production
year. The next digit indicates the month.
WARNING
WARNING
(Example)
1 9 5 2 6 0 3 5 D
Year 2019
Example of month notation:
1 --- January
2 --- February
•
•
•
A --- October
B --- November
C --- December
May
All manuals and user guides at all-guides.com

12
8. WIRE SPECIFICATION
* RB398S/RB518/RB218 are not compatible with TW1061T series or TW1525 series.
9. APPLICATIONS
• Precast concrete panel
• Building foundation
• Commercial building
• Road & Bridge
• Floor heating pipe
10. APPLICABLE REBAR SIZE
MODEL RB398S(CE) RB518(CE) RB218(CE)
TIEWIRE TW898 TW898-PC TW898-EG TW898 TW898-PC TW898 TW898-EG
TYPE OF WIRE Annealed wire Poly-coated
wire
Electro-
galvanized
wire
Annealed wire Poly-coated wire Annealed wire Electro-
galvanized wire
DIAMETER 0.8mm 0.9mm 0.8mm 0.8mm 0.9mm 0.8mm 0.8mm
TIES/COIL Approx.
120 ties
Approx.
105 ties
Approx. 110
ties
(3 Wraps/tie)
Approx. 90 ties
(4 Wraps/tie)
Approx. 75 ties
(3 Wraps/tie)
Approx. 80 ties
(4 Wraps/tie)
Approx. 65 ties
Approx.
170-210 ties
Approx.
155-190 ties
Minimum Maximum
RB398S(CE) 10mm ×10mm (#3 ×#3) 16mm ×19mm (#5 ×#6)
RB518(CE) 16mm ×16mm (#5 ×#5) 22mm ×25mm (#7 ×#8)
RB218(CE) Mesh ×Mesh 10mm ×10mm (#3 ×#3)
Minimum Maximum
RB398S(CE) 10mm ×10mm ×10mm (#3 ×#3 ×#3) 13mm ×13mm ×13mm (#4 ×#4 ×#4)
RB518(CE) 13mm ×13mm ×10mm (#4 ×#4 ×#3) 16mm ×16mm ×25mm (#5 ×#5 ×#8)
Minimum Maximum
RB398S(CE) 10mm ×10mm ×10mm ×10mm
(#3 ×#3 ×#3 ×#3) 13mm ×13mm ×13mm ×13mm (#4 ×#4 ×#4 ×#4)
RB518(CE) 10mm ×10mm ×10mm ×10mm
(#3 ×#3 ×#3 ×#3) 13mm ×13mm ×16mm ×16mm (#4 ×#4 ×#5 ×#5)
All manuals and user guides at all-guides.com

13
11. BATTERY INSTRUCTIONS
About the Battery Level Indicator
(1) To check the battery level (excluding while charging or while operating the charging tool), press the Battery level
check button.
(2) The Battery level gauge is on according to the battery level.
Service Life of the Battery pack
If any condition described below is observed, the Battery pack is at the end of its service life. Replace it with a new one.
Although the Battery pack has been properly charged (fully charged), a great drop in tying time has been noticed.
•Do not charge the Battery pack when this happens. If the motor’s rotational speed slows down, the power of the Battery pack
is considered to be nearly depleted. Using the tool more will cause it to overdischarge, resulting in a shortened service life of
the Battery pack and also in functional trouble of the tool’s main body.
•Do not use a Battery pack when its service life is finished.
This will cause functional trouble in the tool’s main body. Also charging a Battery pack that is out of service life will lead to
functional trouble in the Charger.
Recycling a Li-ion Battery
The MAX battery pack uses a Li-ion battery, it may be illegal to dispose of this Battery into the municipal waste system. Check with your
local solid waste officials for details in your area for recycling options or proper disposal.
When disposing of the Battery pack, make sure to put a Pack cap on its Terminal (with insulating tape securing
it) to prevent short circuits.
Battery level
gauge
Battery level:
0% Battery level: about 0 to 10% Battery level: about 10 to 40% Battery level: about 40 to 70%
Battery level:
about 70 to 100%
All indicators
OFF One red indicator blinks One red indicator ON Two red indicators ON Three red indicators ON
Battery level check button
Battery level gauge
NOTICE
CAUTION
All manuals and user guides at all-guides.com

14
12. OPERATING INSTRUCTIONS
1. How to set the Tiewire
•Set the Main switch (Fig.6.7) at "OFF", the Trigger lock
(Fig.6.8) at "LOCK" and remove the Battery pack
(Fig.6.0), when changing the Battery pack, replacing or
adjusting the Tiewire, abnormalities occur, and the tool is
not being used
1-1 (Fig.9) Press the Release Lever (Fig.9.3) of this
equipment, and confirm that the Release Lever is caught in
the Release Stopper (Fig.9.2).
1-2 (Fig.10) Peel off the tape fixing Tiewire by about 5cm (2").
Stretch out the tip of the wound Tiewire.
Be sure to use only the specified Tiewire (MAX
TW898 Series).
The use of binding wire that has not been specified may cause
breakdown of this equipment. Therefore, be sure only to use the
specified MAX TW898. Do not use binding wire that has become
rusted, since the use of rusted wire will cause equipment
breakdown.
* TW897A, old wire reel cannot be used.
1-3 (Fig.11) Push the Reel stopper (Fig.11.d) to release the
Reel holder (Fig.11.f).
1-4 (Fig.12) Set the Tiewire (Fig.12.c) in the tool by matching
the side of the Tiewire as shown in the picture. Then push
the Reel holder (Fig.12.f) and fix it by sliding the Reel
stopper.
1-5 (Fig.13) Insert the tip of the stretched out Tiewire into the
Wire Guide (Fig,13.m). Then put it into the Pipe (Fig.13.n).
1-6 Put the Wire around 10cm (4") inside the Pipe.
1-7 The tip of the Tiewire should be straightened out to allow it
to pass through the wire feeding mechanism. When
mounting the Tiewire, the wire may become jammed inside
the machine if the wire tip is bent.
(Fig.14) If the window is dirty and the pipe position
can not be confirmed
Open the window and wipe off the dirt on the inside of the window
with a soft cloth, etc. Close the window again after cleaning to
ensure that foreign objects will not be able to enter the machine.
1-8 (Fig.14) Release the Release stopper (Fig.14.2), and
confirm that the Release lever (Fig.14.3) has returned to
its original position and that the Feeding gears (Fig.14.l)
are clamping the Tiewire (Fig.14.c). This completes the
Tiewire mounting operation.
1-9 Remove the tape from the Tiewire completely.
1-10 (Fig.15) Remove slack from wire spool. Make sure the
Tiewire does not get caught behind the wire spool .This
could lead to jamming.
•(Fig.16) When setting the main switch to ON, absolutely
do not bring your hand close to the binding part or rotat-
ing part of the tip of the tool.
•Do not touch the Tiewire during the tying work (while the
machine is operating).
•Do not switch the main switch ON and OFF in rapid suc-
cession, since this operation will cause machine break-
downs.
1-11 (Fig.17) Mount the Battery pack on the tool's main body
until a click is heard. Turn the Main Switch ON.
1-12 (RB518, RB218) (Fig.37) Tool feeds the wire about 150
mm (6") and cuts the wire automatically.Remove the cut
end of the wire with pliers.
1-13 (Fig.18) Set the Trigger lock (Fig.18.8) to the position of
UNLOCK before using the tool.
2. How to remove the Tiewire
•(Fig.6) Set the Main switch (Fig.6.7) at "OFF", the Trigger
lock (Fig.6.8) at "LOCK" and remove the Battery pack
(Fig.6.0).
2-1 (Fig.9) Press the release lever (Fig.9.3), and confirm that
the release lever is caught in the release stopper(Fig.9.2).
2-2 (Fig.19) Remove the Tiewire (Fig.19.c) from the wire guide
(Fig.19.m).
2-3 (Fig.12) Slide the Reel stopper (Fig.12.d) to release the
Reel holder (Fig.12.f) and remove theTiewire (Fig.12.c)
2-4 Mount the new Tiewire. (Refer to the Tiewire mounting
method explanation.)
3. When the Tiewire runs out of binding wire
There should be around 300 mm (12") of the Tiewire left at end
of the spool. This should be discharged with the old spool and be
replaced with a new one.
4. (RB398S) Tension adjustment
(Fig.20) This dial (Fig.20.5) allows you to adjust wire tension
torque slightly. To increase the tension, turn it in the
counterclockwise. To decrease the tension, turn it in the
clockwise.
4. (RB518) Tension and wrap adjustment
(Fig.38) Torque and wrap dial (fig.38.5) allows you to set 3
wraps / tie or 4 wraps / tie and also you can adjust the torque.
To increase the tension, turn it in the counterclockwise.
To decrease the tension, turn it in the clockwise.
4. (RB218) Wire length adjustment
(Fig.40) The Feed dial (Fig.39.5) is a mechanism to adjust feed
rate of the Tie-Wire. When the edge part (Fig.40.x) length is not
appropriate after binding, use this dial to adjust it.
5. Auto Power-off feature
This tool has "Auto Power-off" feature, which saves the power
consumption of the Li-ion battery when the tool is not operated. If
the tool is not operated for 30 minutes, the tool is automatically
turned off. This is "Auto Poweroff". When the power is turned off
automatically, turn the Main switch OFF, then turn ON the switch
again to operate the tool.
6. For proper tightness
6-1 (Fig.22) Tilt the tool 45° angle to the crossed rebars.
6-2 (Fig.23) Apply the tool perpendicularly to the surface of the
crossed re-bars.
During tool operation
•Do not move the tool during tying operation until the tool
stops tying automatically.
6-3 (Fig.24) Tie in alternate direction.
6-4 (Fig.25) Cross tie.
Bend the tail of the first tie before making the second tie.
6-5 (Fig.26) When you need extra tightness, place rebars
(Fig.26.a) at the top of the Arm part (Fig.26.1).
WARNING
NOTICE
WARNING
NOTICE
All manuals and user guides at all-guides.com

15
13. MAINTENANCE
1-1 Regularly inspect the tool
In order to maintain the performance of the tool, periodically
clean up and inspect the tool.
1-2 Do not lubricate the equipment
Absolutely do not lubricate this equipment. Applying
lubrication will remove the grease inside of the tool, and
cause problem on the tool.
1-3 (Fig.27) Regularly clean the feeding mechanism
In order to maintain the performance of the tool, periodically
clean up the mechanism around the feed gear. Using the Air
Duster or like, blow the dust and the iron sand off around the
feed gear.
14. CLEANING MANUAL
When the machine operates for long hours, dust and wire
cuttings may adhere to the cutter section. In such a case,
disassemble and clean the machine according to the following
procedure. (If a wire is caught in the cutter section or wire guide
A, the wire can be removed according to the same procedure.)
(RB398S)
Disassembling
•Do not remove the 2 uncoated bolts.
1-1 Loosen the 2 (plated) Hexagon socket head bolts M3 × 6
(Fig.28.o)
1-2 Remove Arm B (Fig.29.t) and the 2 (plated) Hexagon
socket head bolts M3 × 6 (Fig.29.o).
1-3 Remove the Cutter (Fig.30.p) and the Fixed cutter
(Fig.30.r), and clean them. (The removable parts are the
Cutter (Fig.30.p), Fixed cutter(Fig.30.r), Wire guide A
(Fig.30.q) and Cutter plate unit.(Fig.30.s).)
Assembling
•(Fig.31) Assemble the Fixed cutter (Fig.31.r) so that the
Large hole (Fig.31.b) is set to the rear side and the Small
hole (long hole) (Fig.31.c) is set to the top side.
1-4 Put the pin of the cutter plate unit (Fig.31.s) through the
Cutter connecting rod hole (Fig.31.u) and assemble the
fixed cutter (Fig.31.r) to the unit.
1-5 Fit the Cutter (Fig.32.p) and assemble Wire guide A
(Fig.32.q).
1-6 Align the groove (Fig.33.v) of Wire guide B (Fig,33.w)
attached to Arm B (Fig.33.t) with the Pipe (Fig.34.n), and
assemble Arm B.
1-7 (Fig.35) Make sure that Arm B is securely assembled and
tighten the 2 (plated) Hexagon socket head bolts M3 × 6.
(Fig.35.o) (Tightening torque: 175 cN·m (15.5 lbf·in))
•(Fig.36) Are there any loosening parts?
Make sure that the outer parts are aligned and the parts are
securely assembled without any gap between them.
(RB518) (RB218)
Disassembling
1-1 (Fig.41) Loosen the 2 (plated) Hexagon socket head bolts
M3 × 5 (Fig.41.y).
1-2 (Fig.42) Remove Arm B (Fig.42.z) and the 2 (plated)
Hexagon socket head bolts M3 × 5 (Fig.42.y).
1-3 (Fig.43) Remove the Cutter (Fig.43.D) and the Fixed cutter
(Fig.43.C), and clean them. (The removable parts are the
Cutter, Fixed cutter and Step pin (Fig.43.B).)
Assembling
•(Fig.44) Assemble the Fixed cutter (Fig.44.C) so that the
Large hole (Fig.44.G) is set to the Rear side and the Small
hole (Fig.43.H) is set to the Top side.
1-4 (Fig.45) Insert the step pin (Fig.45.B) into the hole and then
into the Connecting rod (Fig.43.F) hole. Make sure the
Step pin is fully inserted.
1-5 (Fig.46) Make sure that Arm B (Fig.41.z) is securely
assembled and tighten the 2 (plated) Hexagon socket head
bolts M3 × 5 (Fig.46.y). (Tightening torque: 175 cN·m
(15.5 lbf·in))
•The (right) bolt (Fig.46.y) should have the Washer
(Fig.46.E). Install the washer first and then tighten the
bolt.
15. STORAGE
Do not store the tool in a cold weather environment. Keep the tool
in a warm area. When not in use, the tool should be stored in a
warm and dry place. Keep out of reach of children. All quality
tools will eventually require servicing or replacement of parts
because of wear from normal use.
(Fig.21) Remove reel of Tiewire
When you have finished the Tiewire, remove the Tiewire from the
tool.
Store the tool
When you have finished tying work or when the tool will not be
used for a while, switch off the tool, make sure the motor has
stopped, lock the trigger, and remove the battery pack. Tool,
attachments and accessories should be stored in a well-
ventilated dry place where the temperature will not exceed 40°C
(104°F). The battery pack, with a pack cap installed on the pack's
terminal to prevent short circuits, should be stored in a well-
ventilated dry place where the temperature will not exceed 30°C
(86°F).
NOTICE
NOTICE
Rear side Top side
NOTICE
NOTICE
Rear side Top side
NOTICE
All manuals and user guides at all-guides.com

16
16. TROUBLE SHOOTING/REPAIRS
The troubleshooting and/or repairs shall be carried out only by the MAX CO., LTD. authorized distributors or by other specialists.
This tool alerts you to the following conditions by means of a warning sound and warning lamp. The warning lamp is illuminated or blinks,
and is interlocked with the warning sound. Take a countermeasure according to the following table.
•If any of the following conditions occur, be sure to set the Main switch (Fig.1.7) to OFF before carrying out the countermeas-
ures.
•When setting the Main switch to ON, do not touch the tying part of rotating part of the tool's tip.
If the problem is not solved by carrying out the following countermeasures, be sure to set the Main switch to OFF and then
contact the dealer where the equipment was purchased or MAX CO., LTD. authorized distributors.
No. Normal Operation Problem Warning
Sound Cause What to Check Solution
1. Power ON →The
Tip Axis is initialized
and the wire-cutter
operates automati-
cally.
No operation
takes place. No sound emitted. Dead battery (Com- pletely empty) Confirm the battery is charged. Perform normal charge.
Electrode plate has
been oxidized. Taking out the battery, see if electrode has been
browned.
Polish terminal part of
battery pack with dry
cloth, etc.
A long beep
(Piii...) Curl guide (Fig.1.b) is left open. Open/close curl guide Fully close curl guide.
Continuous
short beeps
(Pi, pi, pi, ...)
Binding wire has
been entangled
around Twist sec-
tion.
Turn off power and take
out battery to confirm if
binding wire has been
entangled inside curl
guide.
Turning off power, re-
move binding wire inside
curl guide.
Two short
beeps repeat-
ed for 10 sec-
onds (Pipi,
Pipi, ...), then
power off au-
tomatically
Battery is empty. Confirm the battery is
charged. Perform normal charge.
The Battery pack is
inserted when the
Main switch is ON.
Make sure to insert the
Battery pack, only when
the Main switch is OFF.
Set the Main switch to
OFF, then ON.
2. Power On →LED
lamp is lit. →No op-
eration over 30 min-
utes →LED lamp
goes off. →Al-
though pulling the
trigger, no opera-
tion takes place.
No operation
takes place, al-
though pulling
the trigger
No sound
emitted Normal operation. Set the Main switch to OFF, then ON. Set the Main switch to OFF, then ON.
3. Trigger ON →Wire
sent out. No sending of wire takes place. A long beep (Piii...) Curl guide is left open. Open/close curl guide Fully close curl guide.
Three short
beeps repeat-
ed
(Pipipi,
pipipi, ...)
Tiewire has been run
out. Check if the Tiewire has been run out or not. Set the new Tiewire.
Wire caught inside
reel. Check if wire inside reel has been loosened and
caught.
Remove fray on reel.
Cutter section
(Fig.29) is blocked
with foreign sub-
stance.
Confirm functioning of
Cutter section. Either wipe Cutter sec- tion with dry cloth orblow
it with air.
A wire is caught in
the cutter section or
wire guide A
(Fig.29.q).
Check if any wire is
caught. Disassemble the cutter section and remove the
caught wire. (Fig.28~36)
Five short
beeps
(Pipipipipi,
pipipipipi)
Motor has been
heated. Warning sound does not go continuously. It occurs
only when trigger is
pulled.
Halt Machine and cool it
down.
3. Trigger ON →Wire
sent out. Sending of wire is stopped half-
way.
Four short
beeps repeat-
ed
(Pipipipi,
pipipipi, ...)
Tiewire is not set in
the tool. Check if the Tiewire has been set in the tool. Set the Tiewire.
Binding wire not of
designated types
has been used.
Confirm reel side face. Use MAX Tiewire
TW898.
Three short
beeps repeat-
ed
(Pipipi,
pipipi, ...)
Binding wire has
been entangled in-
side reel.
Confirm reel winding Remove fray on reel.
4. Binding wire draws
a circle. Curl is disor- dered and steps
out of curl guide.
No sound
emitted. Wire, by hitting Rein- forcing bars, was re-
pelled.
Check if wire hits Rein-
forcing bars at binding. Pay attention so that wire does not hit Rein-
forcing bars at binding.
5. Wire is subject to
cutting. No wire cutting takes place. Continuous short beeps.
(Pipipipipipi...)
Cutter section is
blocked with foreign
substance.
Confirm function of Cut-
ter section. Either wipe Cutter sec- tion with dry cloth orblow
it with air.
WARNING
All manuals and user guides at all-guides.com

17
6. Wire twisting takes
place. Wire gets entan- gled. No sound emitted. Wire, by hitting Rein- forcing bars, was re-
pelted.
Check if wire hits Rein-
forcing bars at binding. Pay attention so that wire does not hit Rein-
forcing bars at binding.
A short beep
and a long
beep, repeat-
edly.
(Pipipipipipi...)
Binding wire has
been entangled
around Twist sec-
tion.
Turn off power and take
out battery to confirm if
binding wire has been
entangled inside curl
guide.
Turning off power, re-
move binding wire inside
curl guide.
Binding power is
weak. No sound emitted. Reinforcing bars is not of designated
size.
Confirm size of Reinforc-
ing bars to be bound.
(SEE PAGE 12)
Use appropriate diame-
ter scope.
Erroneous handling
such as improper ap-
plication of Machine.
Confirm how to apply Ma-
chine to Reinforcing bars. Turning Torque dial (Fig.1.5) in + and insert-
ing in vertical direction,
use as tilting at 45°.
(Fig.22)
Function of curl
guide switch Check if curl guide is left open at binding. Do not operate Machine until binding is complet-
ed.
Twisting-off
takes place. No sound emitted. Reinforcing bars is not of designated
size.
Confirm size of Reinforc-
ing bars at binding.
(SEE PAGE 12)
Use appropriate diame-
ter scope.
Erroneous handling
such as improper ap-
plication of Machine.
Confirm how to apply Ma-
chine to Reinforcing bars. Turning Torque dial in – (minus) and inserting in
vertical direction, use as
tilting at 45°. (Fig.22)
Works properly Two short
beeps.
(Pipi)
Low power remains
in the Battery pack. Confirm the battery is ful- ly charged. Perform normal charge after the tying speed
slows down considera-
bly.
The tool is used at
low temperature. Check the temperature at the job site. Leave the tool and the Battery pack at normal
temperature in the room
for some time, and then
continue the operation.
No. Normal Operation Problem Warning
Sound Cause What to Check Solution
All manuals and user guides at all-guides.com

84
RB398S(CE)
EXPLODED
VIEW AND SPARE
PARTS LIST
EINZELTEILDAR-
STELLUNG UND
ERSATZTEILLISTE
SCHEMA ECLATE ET
LISTE DES PIECES
DE RECHANGE
ESPLOSO DEI
COMPONENTI ED
ELENCO DELLE
PARTI DI RICAMBIO
DESPIECE DE LA
MAQUINA Y LISTA
DE RECAMBIOS
BB
34
5
678
9
13
12
14 151617
18
19
21
10 60
22
24
26
27
28
29
30
31
32
33
33
34 35
35
36
37
383940
41
42
43
44 45
46
48
47
47 49
51
52
53
54
55
56
57
58 59
63
64
66
66
69
70
68
72
73
75
76
74
88
78
81
80
82
83
85
89
84
86
87
174
109
91
92
93 94
98
96
106
104
26
105
107
95
115
128
129 131
133
134
135
136
137
130
144
103
61
103
103
103
141
142 66
142
149
143
148
154
153
155
147
142
103
103
116 117 118
26
123
121 122
94
125 126
160
163
120
165
166
167
169
171
142 173
B
C
C
D
G
E
F
E
FG
J
J
b
cw
e
g
k
s
k
n
e
m
99
108
Dr
v
94
99
100
156
161
162
159
A
142
66
66
142
8
n
p
d
d
b
h
s
ua
a
c
wx
x
i
i
t
j
f
j
t
p
103
103
103
u
f
h
v
gr
150
151
144
144
120
144
144
145
176
110
111
111
113
113
112
94
94
114
I
K
II
A
K
H
H
1
A
2
11
20
62
23
65
67 71
65
65
77
90
97
102
103
124
132
127
138
62
79
146
62
146
62
62
B
C
C
D
G
E
F
E
FG
J
J
b
cw
e
g
k
s
k
n
e
m
Dr
v
152
K
A
n
p
d
d
b
h
s
ua
a
c
wx
x
i
i
t
j
f
j
t
p
u
f
h
v
gr
152
65
152
140
67
103
103
II
K
H
H
All manuals and user guides at all-guides.com

85
RB398S(CE)
ITEM
NO.
PART
NO. MATERIAL ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL
1 BB40112 Steel BOLT 3X6 SCHRAUBE 3X6 BOULON 3X6 BULLONE 3X6 PERNO 3X6
2 BB86701 Steel TORX BOLT 3X5 TORX-BOLZEN 3X5 BOULON TORX 3X5 BULLONE DI TORSIONE 3X5 PERNO TORX 3X5
3 RB70404 Steel ARM B UNIT(397) ARMEINHEIT B(397) UNITE DE BRAS “B”(397) UNITA DEL BRACCIO “B”(397) UNIDAD DE BRAZO “B”(397)
4 RB11999 Steel WIRE GUIDE B (397) DRAHTFÖRUNG B (397) GUIDE DE FIL “B” (397) GUIDA Dl CAVO “B” (397) GUIA DE ALAMBRE “B” (397)
5 RB12000 Steel CUTTER MESSER COUTEAU COLTELLO CORTADORA
6 JJ10109 Steel E-RING 2 E-RING 2 CF BAGUE 2 CF E-RING 2 CF ANILLO EN E2 CF
7 RB12090 Steel CUTTER LEVER B (397) MESSERHEBEL B (397) LEVIER DE COUTEAU “B”
(397) LEVA Dl COLTELLO “B” (397) PALANCA DE CORTADORA “B” (397)
8 JJ10514 Steel E-RING 3 CF E-RING 3 CF BAGUE 3 CF ANELLO A "E" 3 CF ANILLO EN "E" 3 CF
9 RB12005 Steel CUTTER LEVER A (397) MESSERHEBEL A (397) LEVIER DE COUTEAU “A”
(397) LEVA Dl COLTELLO “A” (397) PALANCA DE CORTADORA “A”(397)
10 FF51647 Steel HOLLOW PIN 1647 HOHLSTIFT 1647 GOUPILLE CREUSE 1647 PERNO CAVO 1647 PERNO DE ALAMBRE 1647
11 RB12710 Steel SHAFT WELLE ARBRE ALBERO ÁRBOL
12 RB12004 Steel CONNECTING ROD (397) VERBINDUNGSSTANGE (397) BIELLE DE CONNEXION (397) BIELLA (397) BIELA (397)
13 RB12780 Steel PIN STIFT GOUPILLE PERNO PERNO
14 RB11998 Steel WIRE GUIDE A (397) DRAHTFÖRUNG A (397) GUIDE DE FIL “A” (397) GUIDA Dl CAVO “A” (397) GUIA DE ALAMBRE “A” (397)
15 RB12121 Steel FIXED CUTTER (N) UNBEWEGLICHES MESSER (N) COUTEAU FIXE (N) COLTELLO FISSO (N) CORTADORA FIJA (N)
16 RB70493 Steel CUTTER PLATE UNIT MESSERPLATTEN-EINHEIT UNITE DE PLAQUE DE COUTEAU UNITÀ PLACCA COLTELLO UNIDAD DE DISCO DE CORTE
17 RB12781 Stainless steel PLATE PLATTE PLAQUE PLACCA PLACA
18 RB81304 Steel ARM A UNIT ARMEINHEIT A UNITE DE BRAS “A” UNITA DEL BRACCIO “A” UNIDAD DE BRAZO “A”
19 RB11997 Stainless steel LEAF SPRING (397) OBERE BLATTFEDER (397) RESSORT A FEU LLES
SUPER EUR (397) MOLLA A BALESTRA SUPERIORE (397) MUELLE DE HOJAS SUPERIOR (397)
20 AA25113 Steel PAN-HEAD SCREW 2X4 FLACHKOPFSCHRAUBE
2X4 VIS A TETE PLATE 2X4 VITE A TESTA PIATTA 2X4 TORNILLO DE CABEZA LLANA 2X4
21 RB70741 Steel,stainless steel ARM ASSY(398S) ARM-BAUGRUPPE (398S) ENSEMBLE DE BRAS (398S) GRUPPO BRACCIO (398S) CONJUNTO DEL BRAZO (398S)
22 KK33413 Steel SPRING 3413 FEDER 3413 RESSORT 3413 MOLLA 3413 MUELLE 3413
23 BB40839 Steel SCREW 4X16 SCHRAUBE 4X16 VIS 4X16 VITE 4X16 TORNILLO 4X16
24 RB12007 Rubber PIPE SPONGE ROHR-SCHAUMGUMMI EPONGE TUYAU SPUGNA TUBO ESPONJA DE TUBO
26 JJ10101 Steel E-RING 4 E-RING 4 BAGUE 4 E-RING 4 ANILLO EN E4
27 RB81136 Steel,rubber PIPE ASSY RÖHRE ASSY TUYAU ASSY TUBO ASSY TUBO ASSY
28 RB70565 Steel CURL GUIDE UNIT (399A) RÖELFÜRUNG UNIT (399A) DE GUIDE DE BOUCLE UNIT
(399A) Dl GUIDA Dl SPIRA UNIT (399A) DE GUÍA DE ONDULACIÓN UNIT (399A)
29 RB12010 Stainless steel CURL GUIDE COVER WINDEFÜRUNG-
ABDECKUNG COUVERCLE DE GUIDE DE BOUCLE COPERCHIO Dl GUIDA Dl SPIRA CUBIERTA DE GUÍA DE ONDULACIÓN
30 KK33365 Steel TORSION SPRING TORSIONSFEDER RESSORT DE TORSION MOLLA Dl TORSIONE MUELLE DE TORSIÓN
31 RB11708 Steel STOPPER SHAFT ANSCHLAGWELLE ARBRE DE RESSORT ALBERO Dl MOLLA ÁRBOL DE MUELLE
32 RB70567 Steel,stainless
steel CURL GUIDE ASSY (399A) RÖELFÜRUNGS- BAUGRUPPE (399A) ENSEMBLE DE GUIDE DE BOUCLE (399A) GRUPPO DI GUIDA Dl SPIRA (399A) GRUPO DE GUÍA DE ONDULACIÓN (399A)
33 RB11816 Steel HOOK HAKEN CROCHET GANCiO GANCHO
34 RB81113 Steel WS PIN 2.5X10 WS-STIFT 2.5X10 GOUPILLE WS 2.5X10 PERNO WS 2.5X10 PERNO WS 2.5X10
35 RB12014 Steel KEY SCHLÜSEL CLAVETTE CHIAVETTA CHAVETA
36 RB12017 Steel SLEEVE A MANSCHETTE A MANCHON “A” FODERO “A” MANGUITO “A”
37 RB12279 Steel SLEEVE GUIDE MANSCHETTENFÜRUNG GUIDE DE MANCHON GUIDA Dl FODERO GUÍA DE MANGUITO
38 RB70675 Steel TIP AXIS B SPITZACHSE B AXE DE BOUT “B” ASSE Dl ESTREMIT À “B” EJE DE EXTREMIDAD “B”
39 FF31599 Steel PARALELL PIN 1599 ZYLINDERSTIFT 1599 GOUPILLE PARALLELE 1599 PERNO PARALLELO 1599 PERNO PARALELO 1599
40 KK23730 Steel COMP. SPRING 3730 DRUCKFEDER 3730 RESSORT PRESS. 3730 MOLLA COMPR. 3730 MUELLE DE COMP. 3730
41 RB12708 Steel TIP AXIS A SPITZACHSE A AXE DE BOUT “A” ASSE Dl ESTREMITA “A” EJE DE EXTREMIDAD “A”
42 RB12015 Steel SLEEVE B MANSCHETTE B MANCHON “B” FODERO “B” MANGUITO “B”
43 RB12789 Steel CUTTER RING SCHNEIDRING BAGUE DE COUTEAU ANELLO DELLA TRONCHESINA ANILLO DE CORTADORA
44 RB12091 Steel CUTTER RING GUIDE MESSERRING-FÜRUNG GUIDE DE BAGUE DE
COUTEAU GUIDA Dl ANELLO D COLTELLO GUÍA DE AN LLO DE CORTADORA
45 JJ21011 Steel C-RING 14 C-RING 14 BAGUE EN “C” 14 ANELLO IN “C” 14 ANILLO EN “C” 14
46 RB81314 Steel, PA TIP AXIS ASSY SPITZENACHSE-
BAUGRUPPE ENSEMBLE D’AXE DE BOUT GRUPPO DI ASSE DI ESTREMITA GRUPO DE EJE DE EXTREMIDAD
47 RB12020 Steel SPRING COLLAR FEDERHÜLSE COLLIER A RESSORT COLLARE MOLLA COLLAR DE MUELLE
48 KK29026 Steel COMP. SPRING 9026 DRUCKFEDER 9026 RESSORT PRESS. 9026 MOLLA COMPR. 9026 MUELLE DE COMP. 9026
49 RB12019 Urethan rubber BUMPER STOSSDÄMPFER AMORTISSEUR AMMORTIZZATORE AMORTIGUADOR
51 JJ21603 Steel C-RING 20 C-RING 20 BAGUE EN C 20 ANELLO A "C" 20 ANILLO EN “C” 20
52 RB10338 PA INTERNAL GEAR INNENGETRIEBE ENGRENAGES INTERNE INGRANAGGI INTERNl ENGRANAJES INTERNOS
53 RB12783 Steel RING RING BAGUE ANELLO ANILLO
54 RB70745 Steel PLANET CAGE UNIT PLANETENKÄFIG-EINHEIT UNITÉ DE CAGE
PLANÉTAIRE UNITÀ PORTASATELLITI UNIDAD DE JAULA PLANETARIA
55 FF31589 Steel PIN 1589 STIFT 1589 GOUPILLE 1589 PERNO 1589 PERNO 1589
56 RB10341 Steel PLANET GEAR PLANETENGETRIEBE ENGRENAGE PLANETAIRE INGRANAGGIO PLANETARIO ENGRANAJES PLANETARIOS
57 RB10484 Stainless steel GEAR PRESS WHEEL GETRIEBEANDRUCKRAD ROUE DE PRESSION D
ENGRENAGES RUOTA DI PRESSIONE DI INGRANAGGI RUEDA DE PRESIÓN DE ENGRANAJES
58 RB70736 Steel SUN GEAR UNIT SONNENRADEINHEIT UNITE DE PIGNON SOLEIL UNITÀ DI INGRANAGGIO
CENTRALE UNIDAD CENTRAL DE ENGRANAJES
59 RB70734 TWISTING MOTOR DREHMOTOR MOTEUR DE TORSION MOTORE Dl TORSIONE MOTOR DE TORSIÓN
60 EE31131 Steel WASHER 1-3 UNTERLEGSCHEIBE 1-3 RONDELLE 1-3 RONDELLA 1-3 ARANDELA 1-3
All manuals and user guides at all-guides.com

86
61 FF51817 Steel HOLLOW PIN 1817 HOHLSTIFT 1817 GOUPILLE CREUSE 1817 PERNO CAVO 1817 PERNO HUECO 1817
62 BB40810 Steel BOLT 3X16 SCHRAUBE 3X16 BOULON 3X16 BULLONE 3X16 PERNO 3X16
63 RB70710 SENSOR CURCUIT BOARD
F UNIT SENSORSCHALTPLATINEN -EINHEIT F PLAQUETTE DE CIRCUIT DE SENSEUR F
UNITÀ SCHEDA ELETTRONICA
SENSORE "F"
PLACA DE CIRCUITO DE
SENSOR “F”
64 RB81347 Steel,Stainless
steel REEL GUIDE ASSY SPULEFÜHRERVERSAMML UNG ENSEMBLE DE GUIDE DE BOBINE GRUPPO DI GUIDA DI BOBINA CONJUNTO DE GUÍA DE CARRETE
65 AA09501 Steel SCREW 3X6 CF SCHRAUBE 3X6 CF VIS 3X6 CF VITE 3X6 CF TORNILLO 3X6 CF
66 FF51710 Steel HOLLOW PIN 1710 HOHLSTIFT 1710 GOUPILLE CREUSE 1710 PERNO CAVO 1710 PERNO HUECO 1710
67 BB41706 Steel BOLT 4X10 CF SCHRAUBE 4X10 CF BOULON 4X10 CF BULLONE 4X10 CF PERNO 4X10 CF
68 FF31563 Steel PIN 1563 STIFT 1563 GOUPILLE 1563 PERNO 1563 PERNO 1563
69 KK34089 Stainless steel SPRING 4089 FEDER 4089 RESSORT 4089 MOLLA 4089 MUELLE 4089
70 RB70719 Steel, stainless
steel, PC, etc. RATCHET COVER ASSY SCHALTKLINKE- ABDECKUNG BAUGRUPPE ENSEMBLE DE COUVERCLE DE RACHET GRUPPO DI COPERCHIO DEL CRICCO GRUPO DE CUBIERTA DEL TRINQUETE
71 BB40720 Steel BOLT 3X12 SCHRAUBE 3X12 BOULON 3X12 BULLONE 3X12 PERNO 3X12
72 RB12791 PET SPECIFICATION LABEL SCHILD MITTECHNISCHEN
DATEN ÉTIQUETTE DES SPÉCIFICATIONS
TARGHETTA DELLE
CARATTERISTICHE TECNICHE
ETIQUETA DE
ESPECIFICACIONES
73 RB70705 PET, PA MOTOR COVER ASSY
(398S) MOTORABDECKUNGS- BAUGRUPPE (398S) ENSEMBLE COUVERCLE DE MOTEUR (398S) GRUPPO COPERCHIO MOTORE (398S) CONJUNTO DE CUBIERTA DE MOTOR (398S)
74 FF41871 Steel STEP PIN 1871 STUFENBOLZEN 1871 BOULON À GRADINS 1871 PERNO SCALARE 1871 PERNO ESCALONADO 1871
75 KK34067 Stainless steel TORSION SPRING 4067 TORSIONSFEDER 4067 RESSORT DE TORSION
4067 MOLLA Dl TORSIONE 4067 MUELLE DE TORSION 4067
76 EE39609 Urethane rubber PLAIN RUBBER WASHER
1.8X6X2
GUMMI-UNTERLEGSCHEIBE
1,8X6X2
RONDELLE PLATE DE
CAOUTCHOUC 1,8X6X2 RONDELLA PIANA IN GOMMA 1,8X6X2 ARANDELA DE CAUCHO 1,8X6X2
77 BB40714 Steel BOLT 3X50 BOLZEN 3X50 BOULON 3X50 BULLONE 3X50 PERNO 3X50
78 RB12031 PA JOINT FUGE JOINT GIUNTO JUNTA
79 AA21419 Steel SCREW 3X8 CF SCHRAUBE 3X8 CF VIS 3X8 CF VITE 3X8 CF TORNILLO 3X8 CF
80 RB81305 PA, stainless steel,
steel REEL HOLDER ASSY ROLLENHALTER BAUGRUPPE ENSEMBLE DE PORTE- BOBINE GRUPPO DI PORTA- BOBINA GRUPO DE PORTA BOBINA
81 RB70715 PA, Steel, etc. REEL MAGAZINE HASPELMAGAZIN MAGASIN DE BOBINE ALLOGGIO Dl BOBINA ALOJAMIENTO DE BOBINA
82 RB12038 Stainless steel REEL STOPPER SPRING ROLLENANSCHLAG-FEDER RESSORT DE PIECE DE
RETENUE DE BOBINE MOLLA DI ARRESTO DI BOBINA MUELLE DE RETÉN DE CARRETE
83 EE39184 Steel WASHER 3.1X11.8X1 UNTERLEGSCHEIBE
3.1X11.8X1 RONDELLE 3,1X11,8X1 RONDELLA 3.1X11.8X1 ARANDELA 3.1X11.8X1
84 RB12035 POM REEL STOPPER ROLLENANSCHLAG PIECE DE RETENUE DE
BOBINE PARTE Dl ARRESTO Dl BOBINA PIEZA DE RETENClÓN DE BOBINA
85 FF21240 Steel PIN 2.5X6 STIFT 2.5X6 GOUPILLE 2.5X6 PERNO 2.5X6 PERNO 2.5X6
86 RB12036 Stainless steel STOPPER PLATE ANSCHLAGPLATTE PLAQUE DE PIéCE DE
RETENUE PIASTRA DI PARTE DE RITEGNO PLACA DE PARTE DE RETENCIîN
87 RB70427 POM, steel,
stainless steel REEL STOPPER ASSY SPULESTOPPERVERSAMM LUNG ENSEMBLE DE TAQUET DE BOBINE GRUPPO DI BLOCCO DI BOBINA CONJUNTO DEBLOQUE DE CARRETE
88 RB70770 PA, PC, POM, steel,
stainless steel, etc. REEL MAGAZINE ASSY HASPELMAGAZIN ASSY MAGASIN DE BOBINE ASSY ALLOGGIO Dl BOBINA ASSY ALOJAMIENTO DE BOBINA ASSY
89 RB12772 Steel PLATE B PLATTE B PLAQUE “B” PLACCA “B” PLACA “B”
90 BB41707 Steel BOLT 4X16 BOLZEN 4X16 BOULON 4X16 BULLONE 4X16 PERNO 4X16
91 EE11103 Steel SPRING WASHER 2-4 UNTERLEGFEDER 2-4 RONDELLE DE RESSORT 2-4 RONDELLA ELASTICA 2-4 ARANDELA DE MUELLE 2-4
92 EE39825 Steel WASHER 4.5X7.4X0.8 UNTERLEGSCHEIBE
4,5X7,4X0,8 RONDELLE 4,5X7,4X0,8 RONDELLA 4,5X7,4X0,8 ARANDELA 4,5X7,4X0,8
93 KK24175 Steel COMP. SPRING 4175 DRUCKFEDER 4175 RESSORT PRESS. 4175 MOLLA COMPR. 4175 MUELLE DE COMP. 4175
94 JJ10113 Steel E-RING 2.5 E-RING 2,5 BAGUE 2,5 ANELLO A "E" 2,5 ANILLO EN "E" 2,5
95 RB10359 Steel FEEDING GEAR B2 ZUFÜRRAD B2 B2 DENGRENAGES
DAVANCE B2 Dl INGRANAGG DI ALIMENTACI ONE B2 DE ENGRANAJES DE ALIMENTACIÓN
96 RB10362 Aluminum RELEASE LEVER LÖEHEBEL LEVIER DE DECLENCHEMENT LEVA Dl SCATTO PALANCA DE DISPARO
97 FF41809 Steel STEP PIN 1809 STUFENBOLZEN 1809 BOULON À GRADINS 1809 PERNO SCALARE 1809 PERNO ESCALONADO 1809
98 RB12852 Steel HOLLOW PIN HOHLSTIFT GOUPILLE CREUSE PERNO CAVO PERNO DE ALAMBRE
99 EE32104 Stainless Steel WASHER 2-3 UNTERLEGSCHEIBE 2-3 RONDELLE 2-3 RONDELLA 2-3 ARANDELA 2-3
100 RB10357 Steel FEEDING GEAR B1 ZUFÜHRGETRIEBE B1 ENGRENAGES DAVANCE
B1 INGRANAGGIO DI ALIMENTAZIONE B1 B1 DE ENGRANAJES DE ALIMENTACIÓN
102 RB12766 Steel WIRE GUIDE C DRAHTFÜRUNG C GUIDE DE FIL “C” GUIDA Dl CAVO “C” GUÍA DE ALAMBRE “C”
103 CC41104 Steel HEX NUT 1-3 SECHSKANTMUTTER 1-3 ÉCROU HEXAGONAL 1-3 DADO ESAGONALE 1-3 TUERCA HEXAGONAL 1-3
104 RB12761 PA PARTITION PLATE TEILPLATTE PLAQUE DE DIVISION PLACCA Dl DIVISIONE PLACA DE DIVISlÓN
105 RB12765 Rubber PARTITION SPONGE UNTERTEILUNGS-
SCHAUMGUMMI EPONGE DE DIVISION SPUGNA DIVISIONE ESPONJA DE DIVISIÓN
106 EE31133 Steel WASHER UNTERLEGSCHEIBE RONDELLE RONDELLA ARANDELA
107 RB70509 Steel,PA FEEDING GEAR A ASSY ZUFÜRGETRIEBE-BG. A ENSEMBLE “A” D
ENGRENAGES DAVANCE
GRUPPO “A” DI INGRANAGGl
DI ALIMENTAZIONE GRUPO “A” DE ENGRANAJES DE ALIMENTACIÓN
108 RB70729 FEEDING MOTOR ASSY ZUFÜRMOTOR ASSY MOTEUR DAVANCE ASSY MOTORE Dl
ALIMENTAZIONE ASSY MOTORDEALIMENTACIÓN ASSY
109 RB81312 Steel, PA, etc. FEEDING ASSY ZUFÜHR-BAUGRUPPE ENSEMBLE D’AVANCE GRUPPO DI
ALIMENTAZIONE CONJUNTO DE ALIMENTACIÓN
110 RB10368 Steel JAW A BACKE A MACHOIRE “A” GRIFFA “A” QUIJADA “A”
111 KK33249 Steel TORSION SPRING 3249 TORSIONSFEDER 3249 RESSORT DE TORSION 3249 MOLLA Dl TORSIONE 3249 MUELLE DE TORSIÓN 3249
112 RB10370 Steel JAW BASE BACKENBASIS BASE DE MACHOIRE BASE Dl GRIFFA BASE DE QUIJADA
113 FF41822 Steel STEP PIN 1822 STUFENBOLZEN 1822 BOULON À GRADINS 1821 PERNO SCALARE 1822 PERNO ESCALONADO 1822
114 RB10369 Steel JAW B BACKE B MACHOIRE “B” GRIFFA “B” QUIJADA “B”
115 RB70495 Steel JAW BASE ASSY BACKENBASIS ASSY BASE DE MACHOIRE ASSY BASE Dl GRIFFA ASSY BASE DE QUIJADA ASSY
116 RB12769 Steel ROTARY PIN DREHSTIFT GOUPILLE ROTATIVE PERNO ROTANTE PASADOR GIRATORIO
RB398S(CE)
ITEM
NO.
PART
NO. MATERIAL ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL
All manuals and user guides at all-guides.com