MaxLite GuardMax SECS Series User manual

Operating Instructions SECS Series
• To reduce the risk of death, personal injury or property damage from
fire, electric shock, falling parts, cuts/abrasions, and other hazards
read all warnings and instructions included with and on the fixture
box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
• Consult a qualified electrician to ensure correct branch circuit conductor.
WAR I G:
RISK OF ELECTRICAL SHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring
fixture to the power supply.
• Do not install fixture in the rain to reduce risk of electrical shock.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire
label information.
• Make all electrical and grounded connections in accordance with the
ational Electrical Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTIO :
RISK OF I JURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTIO :
RISK OF FIRE
• Do not use electric generator to test LED fixture.
• Keep combustable and other materials that can burn away from luminaire and lamp/lens
• MI 75°C SUPPLY CO DUCTORS.
Model:
SECS20UCSBPC
SECS26UCSBPC
SECS15UCSBPC
© Copyright 2020. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, N 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 1
REV: 4/16/20
General Safety Information
MaxLite GuardMax Small Profile Wall Pack
®
Picture is for illustration
purposes only.
Your model may vary.

Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the
fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
ote: There is an “UP” label on the fixture’s backplate to indicate proper orientation.
2 - Direct J-Box/Wall Installation
Page: 2
REV: 4/16/20
2. Loosen the four screws shown in
diagram below.
3. Remove the 1/2 end cap.
4. Peel off the yellow sticker
and apply it to the round
area of the bottom plate.
5. Fix the bottom plate to the
round plate.
6. Make your wiring connections.
7. If you do not wish to use the
photocell, unplug connector
located at the top of fixture
housing.
9. Turn on the power after
making sure all screws are
tightend and the wire
connections are properly made.
1 - General Wiring Diagram
CAUTIO : Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
(+) LINE
(-) COMMON
GROUND GREEN / YELLOW-GREEN
WHITE / BLUE
BLACK / BROWN
Light
Fi ture
1. Turn off the power.
© Copyright 2020. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, N 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
8. Replace bottom plate and
tighten the four screws.
Operating Instructions SECS Series
MaxLite GuardMax Small Profile Wall Pack
®

3 - Surface Conduit Installation
© Copyright 2020. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, N 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 3
REV: 4/16/20
2. Loosen the four screws shown in
diagram below.
3. Place the black sponge pad on
the bottom plate.
4. Screw the bottom
plate into the
wall.
5. Remove one of the 1/2 end caps
and pull wires through.
6. Make your wiring
connections.
8. Replace bottom plate and
tighten the four screws.
9. Turn on the power after making
sure all screws are tightend
and the wire connections are
properly made.
1. Turn off the power.
Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the
fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
ote: There is an “UP” label on the fixture’s backplate to indicate proper orientation.
ote: Adjust DIP switch on the back
of the fixture to select the
desired CCT.
7. If you do not wish to use the
photocell, unplug connector
located at the top of fixture
housing.
Operating Instructions SECS Series
MaxLite GuardMax Small Profile Wall Pack
®

MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the earlier of the actual installation date
or 90 days after the original date of purchase from a MaxLite authorized distributor/dealer (the “Warranty Period”), as
follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship,
MaxLite will, at its option, repair it, replace it with the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete coverage details as well
as the terms and conditions of our warranty. Please note that it is NOT a requirement to register your warranty in order
to initiate a warranty claim unless a Ten Year warranty has been purchased separately, or when applicable and/or
purchased separately, your warranty contains a replacement labor allowance.
Limitation of Liability
THIS WARRANTY IS EXCLUSIVE, AND IS THE SOLE REMEDY FOR ANY AND ALL CLAIMS, WHETHER IN
CONTRACT, IN TORT OR OTHERWISE ARISING FROM THE FAILURE OF PRODUCT AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, WHICH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED TO
THE EXTENT PERMITTED BY LAW AND, IN ANY EVENT, SHALL BE LIMITED TO THE WARRANTY PERIOD
SPECIFIED ABOVE. THE LIABILITY OF MAXLITE SHALL BE LIMITED TO THE TERMS OF THE EXPRESS
WARRANTY SET FORTH HEREIN. IN NO EVENT WILL MAXLITE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES RESULTING FROM LOSS OF
USE, PROFITS, BUSINESS OR GOODWILL, LABOR COSTS, REMOVAL OR INSTALLATION COSTS, WHETHER
OR NOT MAXLITE HAS BEEN ADVISED OF THE POSSIBILITY THEREOF. UNDER NO CIRCUMSTANCES SHALL
MAXLITE’S ENTIRE LIABILITY FOR A DEFECTIVE PRODUCT EXCEED THE PURCHASE PRICE OF THAT
PRODUCT (EXCLUDING LABOR WARRANTY COVERAGE WHERE SPECIFCALLY OFFERED BY MAXLITE).
WARRANTY SERVICES PROVIDED UNDER THESE TERMS AND CONDITIONS DONOT ENSURE THE
UNINTERRUPTED OPERATION OF PRODUCTS; MAXLITE SHALL NOT BE LIABLE FOR DAMAGES CAUSED
BY ANY DELAYS INVOLVING WARRANTY SERVICE.
This Warranty gives you specific legal rights and you may also have other rights that may vary from state to state.
Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental
damages, such limitation may not apply to you.
Warranty Information
© Copyright 2020. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, N 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 4
REV: 4/16/20
Operating Instructions SECS Series
MaxLite GuardMax Small Profile Wall Pack
®