MaxLite SEC Series User manual

Operating Instructions SEC Series
• To reduce the risk of death, personal injury or property damage from
fire, electric shock, falling parts, cuts/abrasions, and other hazards
read all warnings and instructions included with and on the fixture
box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• For Residential installation: f you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code.
• DO NOT NSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
WA NING:
ISK OF ELECT ICAL SHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring
fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire
label information.
• Make all electrical and grounded connections in accordance with the
National Electrical Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
ISK OF INJU Y
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
ISK OF FI E
• Keep combustable and other materials that can burn away from luminaire and lamp/lens
• MIN 90°C SUPPLY CONDUCTO S.
This instruction manual applies to the SEC Series
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 1
REV: 10/02/18
General Safety Information
Photos are for illustration purposes
only. Your model may vary.
MaxLite GuardMax Entry Wall Pack
®

General Wiring Diagram
CAUTION: Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
(+) LINE
(-) COMMON
GROUND GREEN
WHITE
BLACK
Li ht
Fixture
SPD
LED Driver
House Grounding
V-(Black)
V+(Red)
AC NPUT
120-277VAC
N
L
GNDGND
L
N
GNL
photocell sensor
Brown
(L / Li)
Blue
(N)
Red
(Load/Lo)
(Surge Protection Device)
Standard product with surge protector and photo control
Operating Instructions SEC Series
MaxLite GuardMax Entry Wall Pack
®
Page: 2
REV: 10/02/18
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
208/240V Connections
LINE 1
LINE 2
GROUND
BLACK
WHITE 120-277V Driver
Sur e Protection Device
WHITE
BLACK
GREEN

Diffuser
Reflector Sheet
Sensor Cap
Back Plate
Bolt
DC
AB
Back Plate
Main Power
Screw
Water-proof J-Box
Reflector Sheet
Diffuser
Main
Power
Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the
fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
1. Begin by removing the diffuser using 6 screws and reflector sheet by squeezing tabs on its side.
Note: Remove sensor cap if using photocontrol otherwise leave it in place. (Fig. 1)
2. Unscrew bolt, make note of the 4 holes (A, B, C and D in Fig. 2)
3. Junction Box Mounting: Feed main power wires through back plate and mount back plate to water-proof J-box. (Fig. 3)
Conduit Mounting: Feed main power wires through ½” threaded conduit hole on the bottom of the back plate and mount
back plate against the wall. (Fig. 3)
4. Wire main power (see wiring diagram on page 2) and put reflector sheet back on by squeezing the toolless tabs on each
side. Connect ground to grounding screw. Lock diffuser firmly to back plate. Make sure top and bottom are oriented
correctly by referring to the marking on the shield. (Fig. 4)
Note: This fixture is wet location rated. n order to ensure that moisture does not enter the outlet box and cause a short
circuit, clear caulking should be used to seal the space between the fixture mounting bracket and the wall. Ensure that a
space is left at the bottom to allow for the escape of moisture. t is recommended that outdoor silicone sealant be used for
that purpose.
Back Plate
Bolt
DC
AB
Back Plate
Main Power
Screw
Wall
Reflector Sheet
Diffuser
Main
Power
Junction Box Mounting:
Mounting Instructions
Conduit Mounting:
Junction Box Mounting: Conduit Mounting:
Junction Box Mounting: Conduit Mounting:
Operating Instructions SEC Series
MaxLite GuardMax Entry Wall Pack
®
Page: 3
REV: 10/02/18
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]

MaxLite nc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from
MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: f a Product fails to operate during the
Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with
the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete
terms and conditions of our warranty.
Limitation of Liability
THE FOREGO NG WARRANTY S EXCLUS VE, AND S THE SOLE REMEDY FOR ANY AND ALL CLA MS,
WHETHER N CONTRACT, N TORT OR OTHERW SE AR S NG FROM THE FA LURE OF PRODUCT AND S N
L EU OF ALL OTHER WARRANT ES, EXPRESS OR MPL ED, NCLUD NG ALL WARRANT ES OF
MERCHANTAB L TY OR F TNESS FOR A PART CULAR PURPOSE, WH CH WARRANT ES ARE HEREBY
EXPRESSLY D SCLA MED TO THE EXTENT PERM TTED BY LAW AND, N ANY EVENT, SHALL BE L M TED TO
THE WARRANTY PER OD SPEC F ED ABOVE. THE L AB L TY OF MAXL TE SHALL BE L M TED TO THE TERMS
OF THE EXPRESS WARRANTY SET FORTH HERE N. N NO EVENT W LL MAXL TE BE L ABLE FOR ANY
SPEC AL, NC DENTAL OR CONSEQUENT AL DAMAGES NCLUD NG, W THOUT L M TAT ON, DAMAGES
RESULT NG FROM LOSS OF USE, PROF TS, BUS NESS OR GOODW LL, LABOR COSTS, REMOVAL OR
NSTALLAT ON COSTS, DECREASE N THE L GHT OUTPUT OF THE LAMP, AND/OR DETER ORAT ON N THE
LAMP’S PERFORMANCE, WHETHER OR NOT MAXL TE HAS BEEN ADV SED OF THE POSS B L TY THEREOF.
UNDER NO C RCUMSTANCES SHALL MAXL TE’S ENT RE L AB L TY FOR A DEFECT VE PRODUCT EXCEED
THE PURCHASE PR CE OF THAT PRODUCT. WARRANTY SERV CES PROV DED UNDER THESE TERMS AND
COND T ONS DO NOT ENSURE THE UN NTERRUPTED OPERAT ON OF PRODUCTS; MAXL TE SHALL NOT BE
L ABLE FOR DAMAGES CAUSED BY ANY DELAYS NVOLV NG WARRANTY SERV CE.
This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to
state. Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or
incidental damages, this limitation may not apply to you.
Warranty Information
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Operating Instructions SEC Series
MaxLite GuardMax Entry Wall Pack
®
Page: 4
REV: 10/02/18