Maxon DE-25 User manual

Figure1-3.3Figure 1-3.2Figure 1-3.1
Automatic bolts* 4
particles*4
Expanded colloidal
M4x20 screws* 4
Screws*5
Inner-Hexag on
M5x15 screws*4
449
long
Extended
E
Wall hanging
(No accessories for
non wall hanging )
special
C款
B款E款
H
200＋LA
820＋LA
H
131.5
241+160
H
D款
45+LA
H
Figure1-3.4
160 226 319 223 184
—
316
D
Wall hanged
226 319 223 316 267 427 160
226 319 223 316
112
130 18
226 319 223 316 887 1047 160
115 180
315
±15°
±5°
LC
LB
it aside for future use.
mount , pls read the manual carefully before using. Keep
Dear custo m ers: Thanks for choosing our DE-25 projector,
DE-25 projector mount user manual
Figure 1-1 Main View Left View Top View
Max Load ：40Kg
Product Appearance
size
Product
Type
Short Pole
C
Long Pole
Width W （mm ）
Length L（mm ） Height H （mm ）
LA (mm)
Tube stretch length
Min Max Min Max Min Max
Installation hole distance
4 holes LC（mm ）
3 holes LB（mm ）
Min left/ri ght adjustable an gle
MA X ±3°
tilt adjustable an g le
up/down
adjustable
an gle Figure 1-2
Accessories
Mounting Board Tube Mounting feet
Allen Key
Gloves
type B

Installation Steps
Figuer1-4
1 2 3
Ceiling expanded colloidal particles
Electric drill
Borehole site
Ceiling
Mounting board
ceiling
Outer tube
Cables
Axial screws
adjusting
1
2
Hoisting
1
2
Step1: Take out the mounting board and
tube, then screw out 3 bolts on the tube
mounting board (be aware of direction)
Align the hole position of tube and
and screws the boits in the hole. Refer figure 1-4
Figuer1-6 Figuer1-7
Figuer1-5
Step2:Take out the mounting feet refer figure 1-5
Separate component ① and ② among the guide
chute. Refer figure 1-6.
Figure 1-4 part. Then screw the bolts.
Step 3: Align the hole of component ② and
Refer figure1-7
Figuer1-8 Figuer1-9
Step 4-1: Align the assembly ① with the assembly in Figur1-4
and screw in the screw. Refer figure 1-8
Step4-2: Determine the mounting position in the ceiling, then stick
Refer figure 1-9.(Suitable for ceiling hoisting and installation)
expanded colloidal particles, mount the mounting board in the ceiling.
stickers on the drill holes, use drilling tool drill 4Φ10holes, insert
handle
Figuer1-11Figuer1-10
adjusting handle
adjust tilt inner hexagon screws adjust screws (2 sides)
adjust screws (horizontal, left,right)
(2 sides)
Step4-3: Thread the cable of projector in the inner tube
insert the inner tube into the outer tube that mount it in
Refer figure 1 - 1 0.(Suitable for ceiling hoisting and installation)
guide chute and lock 4 adjusting screws on left&right
installing projector) hang it on the axial screws among the
the ceiling, lift the mounting feet with 2 hands (finish use allen key looses bolts on 2 sides, rotate the part of mounting feet and tighten
then adjust the height and tighten the screw, projector tilt angle adjustment:
1-2 bolts in case angle tilt, tighten other bolts after confirming angle. Refer figure 1-11
Step4-4: Adjust projector:Height adjustment:loose screw of adjusting handle

！
！
Figuer1-16
Figuer1-15Figuer1-14
Figuer1-12 Figuer1-13
Please ensure the ceiling/wall can load 50KG to
prevent accident from happening.
Don'ttilttheprojectortoomuch,antifalling,
screws shouldbetighten.
Don't take apart any components after hanging.
No dismantle
Attention
Warning
Step 5-4: reference for wall mounting commissioning (hoisting step 4.4)
adjusting handle
adjust screws (2 sides)
adjust tilt inner hexagon screws
(2 sides)
adjust screws (horizontal, left,right)
Safety precautions before
installation and use
Electric drill
Borehole site
Wall mounting
Step 5-1 wall mounting assembly: pay attention to the direction
when installing the elbow. Install the elbow with M5 * 16 screws
(Refer figure 1-12 )
Step 5-2: determine the position of hanger to be installed on the wall,
paste the label of drilling position, align the hole location with drilling tool,
drill 4 Φ 10 holes, knock in expanded rubber particles,
and screw in ST6 * 45 self tapping screw to install the top mounting plate
assembly on the wall. Refer figure 1-14 (suitable for wall mounting)
Step 5-3: after passing the corresponding wire rod of the projector
through the inner tube, lift the octopus with both hands
(with the projector installed) and hang it on the axial screw along
the guide chute, and lock the left and right four adjusting screws,
Refer figure 1-15 (suitable for wall mounting)