Maxon DE-50 User manual

Installment Instruction
Projector Mount
Model: DE-50
Thanks so much for your purchase, please read this instruction before installment.

Ceiling Mount Ceiling Mount Procedure
DE-50 composition
ceiling mounting plate
outer tube
inner tube
projector mounting foot
worm knob
side knob
combination knob
plastic wire cover
standard 4-foot image long pole height image
Max Height: 440mmMin Height: 290mm
short pole height image
Min Height: 136mm Max Height: 140mm
M6×25 inner hexagon screws 4pcs
M5×20 inner hexagon screws 4pcs
M4×20 inner hexagon screws 4pcs
expansion plastic screw socket 4pcs
inner hexagon screws wrench 4pcs
φ6 self-tapping screws 4pcs
(6)
(7) plastic gaskets 4pcs
installment instruction 1pc
glove 1 pair
customer owned tool φ10 percussion drill 1pc
Accessories
1. Max load: 35KG
2. Install it on the suitable position according to the height of projector mount
3. Install it into the concrete on the ceiling, make sure bear the weight of projector
and projector mount

Ceiling Mounting Procedure
M4 inner hexagon screws
Pic1
Pic2
φ6 self-tapping screws
expansion plastic screw socket
1. After projector mounting plate aligns at
the screws holes, use M4 inner hexagon
screws to fix it.
2. Mark the screws holes position after putting the projector mounting
plate at the suitable position, punch with percussion drill, fix with
screws finally.
Pic5
Notice: In order to avoid falling and hurting somebody, must make
sure the position is so strong that can bear the weight of
projector and projector mount.
wormknob
Pic3
Pic4
Pic6
3. Align the auxiliary rod with the holes of the adapter, and screw in the M5 inner hexagon screws from the bottom to the up.
If the screw holes are blocked and the screws cannot be screwed in, the projector mount can be rotated horizontally to
stagger the screw holes by rotating the worm knob to achieve screws-in.
Notice: The adapter and the foot have been installed for the customer before delivery, in order to make the installation
steps clearer, just omit the foot in Pic 3, please do not remove the foot when installation.
M5 inner hexagon screw
4. Fix the projector mounting foot to the projector according to the distance of the holes of the
projector, see Pic 5. The Pic takes the standard four feet projector mount as an example. If
the projector just has 3 holes, can remove one of the feet, then install it.
height screw lock
6.Afterfinishingprojector’sinstallment,insertthewholeunitintothemainpolethroughthe
auxiliary pole, see Pic 6, insert into the main pole with a height screw lock, tighten it, and
the installation is complete.
Notice:Pleasebecarefulwheninstallment,orinstallitbyaprofessional,toavoidinjury.

Ceiling Mount Procedure
DE-50 side mount standard pole length
Max Length: 410mm
Min Length: 324mm
Max Load: 35KG
Notice: In order to avoid falling and hurting somebody, must make
sure the position is so strong that can bear the weight of
projector and projector mount.
M4innerhexagonscrew φ6 self-tapping screws
expansionplasticscrewsocket
screwholecap
1. After projector mounting plate aligns at
the screws holes, use M4 inner hexagon
screws to fix it.
2. Mark the screws holes position after putting the projector mounting
plate at the suitable position, punch with percussion drill, fix with
screws finally.
Notice: In order to avoid falling and hurting somebody, must make
sure the position is so strong that can bear the weight of
projector and projector mount.
6×10 round flat screw
plastic cap
side mount head
adapter
worm knob
3. Insert the auxiliary pole into the side mount head, tighten them with 6×10 round flat screws then
insert the plastic cap into the side mount head, see Pic 9. After completion, put the adapter into
the side mount head, and tighten. If the screw holes are blocked and the screws cannot be screwed
in, the projector mount can be rotated horizontally to stagger the screw holes by rotating the worm
knob to achieve screws-in.
Pic9
4. Put the auxiliary pole into main pole, tighten the height
screw lock, side mounting completes
M5×10
Pic10
Angle Adjustment
①-sideknob
②-rear foot knob
③-front foot knob
Loose to move the center distance of
the front and rear feet back and forth
Twist to move the rear feet back and forth
Twist to move the front feet back and forth
Pic11-1 Pic11-2

Combination Knob: loose the 2 bottom knobs to unlock, then twist the 2 top
knobs to adjust the inclination angle of projector mount
loose this knob to adjust the angle
Notice: The knobs on both sides need to be twisted at the same time to adjust the height of
the projector mount uniformly, if just twist one side, the height will be inconsistent.
Worm Knob:twistthisknobtorotate
horizontally
Feet Size
Max: φ527 Min: φ230
Installment and Use Safety Precautions
Notice
Warn
NO
For safaty, the ceiling must bear 4 times of weight of projector and
projector mount at least
Please don’t incline the projector extremely
Please don’t remove the parts of projector mount
This installation instruction is written for dealers and installers, please do not
install by yourself, and be sure to hire qualified professional installer to install and
strictly follow the contents of this installation instruction.