DE-35 projector mount user manual
Product appearance Figure 1-2
Figure 1-1 Main view Left view Top view
Length L (mm) Width W (mm)Height H (mm)
(Long + short pole)
(Wall tiles)
(Long Pole)
(Short Pole)
Min Max MinMin Max Max
(Extended long)
(Long tube)
(Short tube)
Product
Type
Figure 1-3
Tube expansion
length
Rated load
(Bearing)
Min Max
Installation hole distance
(mm)
3 holes LB
4 holes LC
Mounting hole type
Section B Section ESection DSection C
Figure 1-3.1 Figure 1-3.2 Figure 1-3.3 Figure 1-3.4
Accessories
left/right adjustable angle
tilt adjustable angle
up/down adjustable angle
Mounting Board Tube Allen Key Gloves
Inner-Hexagon
Screws*5
ST6*45Automatic
bolts*4
Wall hanging special
(No accessories for
non wall hanging)
Plastic pad for hanger
installation*4
Installation Steps
Figure 1-8
Figure 1-4
Figure 1-9
Figure 1-6 Figure 1-7
Figure 1-10 Figure 1-11
Figure 1-5
Step 1: open the package, take out the
upper top plate, and pipe components, screw
out the three screws on the pipe, align the
round pipe with the upper top plate (pay
attention to the direction prompt), and then
screw in the screws for fastening connection.
Refer figure 1-4
Step 2: take the octopus out of the packing
box, as shown in Figure 1-5, and separate the
components and along the guide groove
by hand. Refer figure 1-6
Step 3: install the assembly with the
projector. According to the actual size
of the projector (the installation hole
position is different), each group of
connecting arms and movable arms
are fastened, and the distance locking
screw can be adjusted appropriately.
Refer figure 1-7
Hoisting
Step 4-1: align the assembly with the assembly
in Figure 1-4, and screw in the screw (Refer figure 1-8 )
Ceiling
Borehole site
Electric drill
expanded colloidal particles Ceiling
Mounting board
Step 4-2: determine the position of the hanger to be installed on the ceiling,
paste the label of the drilling position, use the drilling tool to align the hole
position, drill four Φ 10 holes, knock in the expanded rubber particles, and
screw in the st6x45 self tapping screw to install the upper roof assembly
on the ceiling. Refer figure 1-9 (Suitable for ceiling hoisting and installation)
Step 4-3: put the corresponding wire rod of the projector
through the inner tube, insert the inner tube into the pipe
on the fixed ceiling, lift the octopus (installed for speculation)
with both hands to hang the axial screw along the guide
chute, and lock the left and right four adjusting screws.
Refer figure 1-10 (suitable for ceiling hoisting and installation)
Step 4-4: debugging the projector: height adjustment: loosen the
adjusting handle screw, adjust the screw up and down by hand, and
then tighten the screw; debugging the projector inclination angle: first
loosen the screws on both sides with a hexagon wrench, turn the
octopus assembly by hand to make the projector obtain the required
inclination angle, tighten 1-2 screws to prevent angle deviation, and
then tighten the remaining screws after confirming the angle.
Refer figure 1-11
Axial screws
Cables
Adjusting handle
Ceiling
Outer tube Adjusting handle
Adjust tilt inner hexagon screws
(2 sides)
Adjust screws
(horizontal, left,right)
Adjust screws (2 sides)
1 2 3
12
1
±5°
±5°
±15°
200+LA
H
45+LA
H
LC
LB
W
L
820+LA
H
1
2
1
245 345 266 426 160
245 345 110 125 18
245 345 173 179 160 20
245 345 266 426 160
245 345 110 125 18
245 345 890 1050 160
LA（mm） KG
35
35
Please read it carefully before use.
Thank you for purchasing DE-35 fixed hanger.
Dear users:
DE-35
DE-20
DE-35
DE-35
DE-35
250 350
250 350
250 350
250 350
250 350
250 350
（ ）radius 112 205
（Diagonal hole）285 450
200+LA
H
2
size
Mounting feet
M5x15 screws*4 M4x20 screws* 4
Expanded colloidal
particles*4
2
